From afc8f9ff30b9c026bd8b5b678748e6b23913d867 Mon Sep 17 00:00:00 2001
From: Andreas Auras <yak54@gmx.net>
Date: Wed, 10 Feb 2010 12:55:37 +0100
Subject: More modifications for public use of project

---
 usb_boot/usbconfig.h | 60 ++++++++++++++++++++++++++--------------------------
 1 file changed, 30 insertions(+), 30 deletions(-)

(limited to 'usb_boot/usbconfig.h')

diff --git a/usb_boot/usbconfig.h b/usb_boot/usbconfig.h
index e9899b7..70f76f1 100644
--- a/usb_boot/usbconfig.h
+++ b/usb_boot/usbconfig.h
@@ -183,17 +183,17 @@ section at the end of this file).
  * Please note that Start Of Frame detection works only if D- is wired to the
  * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
  */
-
-/* Save timestamp of sof */
 
-#ifdef __ASSEMBLER__
-macro customSofHook
-		ldi			YL, 0
+/* Save timestamp of sof */
+
+#ifdef __ASSEMBLER__
+macro customSofHook
+		ldi			YL, 0
     out     TCNT1H, YL
     out     TCNT1L, YL
 endm
 #endif
-
+
 #define USB_CFG_CHECK_DATA_TOGGLING     1
 /* define this macro to 1 if you want to filter out duplicate data packets
  * sent by the host. Duplicates occur only as a consequence of communication
@@ -206,15 +206,15 @@ endm
 /* define this macro to 1 if you want the function usbMeasureFrameLength()
  * compiled in. This function can be used to calibrate the AVR's RC oscillator.
  */
-#define USB_USE_FAST_CRC                1
-/* The assembler module has two implementations for the CRC algorithm. One is
- * faster, the other is smaller. This CRC routine is only used for transmitted
- * messages where timing is not critical. The faster routine needs 31 cycles
- * per byte while the smaller one needs 61 to 69 cycles. The faster routine
- * may be worth the 32 bytes bigger code size if you transmit lots of data and
- * run the AVR close to its limit.
- */
-
+#define USB_USE_FAST_CRC                1
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
 /* -------------------------- Device Description --------------------------- */
 
 #define  USB_CFG_VENDOR_ID       0xc0, 0x16
@@ -360,9 +360,9 @@ endm
  */
 #define USB_INTR_CFG            MCUCR
 #if defined(USB_COUNT_SOF) || defined(USB_SOF_HOOK) || 1
-#define USB_INTR_CFG_SET        ((1 << ISC11))
+#define USB_INTR_CFG_SET        ((1 << ISC11))
 #else
-#define USB_INTR_CFG_SET        ((1 << ISC10) | (1 << ISC11))
+#define USB_INTR_CFG_SET        ((1 << ISC10) | (1 << ISC11))
 #endif
 /* #define USB_INTR_CFG_CLR        0 */
 /* #define USB_INTR_ENABLE         GIMSK */
@@ -370,22 +370,22 @@ endm
 /* #define USB_INTR_PENDING        GIFR */
 #define USB_INTR_PENDING_BIT    INTF1
 #define USB_INTR_VECTOR         SIG_INTERRUPT1
-
-
-/* This is a new macro that is executed and the beginning of the usb irq handler.
- * This needs a patch in the corresponding clock dependend assembler file of VUSB!!!
- * It is save to use register YH here
- */ 
-/*#define USB_START_IRQ_HOOK	customTriggerHook*/
-
-
+
+
+/* This is a new macro that is executed and the beginning of the usb irq handler.
+ * This needs a patch in the corresponding clock dependend assembler file of VUSB!!!
+ * It is save to use register YH here
+ */ 
+/*#define USB_START_IRQ_HOOK	customTriggerHook*/
+
+
 /* Reinstall edge level interrupt triggering (after sleep) */
 #ifdef __ASSEMBLER__
-macro customTriggerHook
-    in     YH, USB_INTR_CFG
+macro customTriggerHook
+    in     YH, USB_INTR_CFG
 		ori 	 YH, USB_INTR_CFG_SET
     out    USB_INTR_CFG, YH
-endm
+endm
 #endif
-
+
 #endif /* __usbconfig_h_included__ */
-- 
cgit v1.2.3