--------------------------------------------------------------------- GraphLCD driver library The AX 206 digital photoframe driver --------------------------------------------------------------------- Description ----------- The ax206dpf driver supports AX 206 based DPFs. For more information about these DPFs see: http://tech.section5.ch/news/?p=68 The driver was tested with this display: http://www.pearl.de/a-PX1184-5618.shtml or http://www.pearl.de/a-HPM1184-5618.shtml Important Notes --------------- This driver is experimental and not enabled by default. To use this driver uncomment the HAVE_AX206DPF_EXPERIMENTAL line in Make.config and recompile the library. The DPF does not work out of the box with this driver. It has to be modified with a custom firmware (see "Hacking your DPF"). If your DPF is already hacked, there is no need to install the "dpf-ax" package described in "Hacking your DPF". All necessary routines to access a hacked DPF are included in this driver. Non-root users -------------- The driver needs write access to /dev/proc/usb. So the calling user must be root or you have to modify the access rights for /dev/proc/usb. For Debian/Ubuntu this can be done with a custom udev rule like: SUBSYSTEM=="usb", ENV{DEVTYPE}=="usb_device", MODE="0664", GROUP="" Replace with a group the calling user belongs to. Put this rule in a new file "nn-usbuser.rules" in /etc/udev/rules.d. Replace "nn" by two digits that are lower than any existing usb rule. For my Ubuntu 10.04 system I used "/etc/udev/rules.d/35-usbuser.rules". Configuration Parameters ------------------------ The driver supports the following parameters in config file: Device Selects a specific display. 'dpf0' = first detected display, 'dpf1' = second detected display, ... Default value: 'dpf0' Width Sets the horizontal size of the display. If this parameter is not given, a default value according to the selected DPF is used. Default value: 320 or 240 (see 'Portrait') Height Sets the vertical size of the display. If this parameter is not given, a default value according to the selected DPF is used. Default value: 240 or 320 (see 'Portrait') UpsideDown Rotates the display output by 180 degrees. This might be useful, if the LCD is mounted upside-down. Possible values: 'yes', 'no' Default value: 'no' Portrait Select portrait or landscape mode. Rotate display output by 90 degrees if necessary. Possible values: 'yes' -> default size = 240 x 320 'no' -> default size = 320 x 240 Default value: 'no' Zoom Determines if pixels should be magnified. Possible values: 1, 2, 3, 4 Default value: 1 Hacking your DPF ---------------- For hacking your DPF you need this dpf-ax package: http://tech.section5.ch/files/dpfhack-0.12devel.tgz First of all, let me quote this from the dpf-ax README ((c) 4/2011, hackfin): [quote] Also note: NO SUPPORT! NO WARRANTY! FRIENDS DON'T MAKE FRIENDS HACK THEIR DPF! LET ALONE NON-FRIENDS! (Bottomline: Don't ask me if I can hack your DPF). If you wish to hack your DPF, please check the sites listed below. . . Find updates and documentation here: http://tech.section5.ch/news/?p=68 or here: http://picframe.spritesserver.nl/wiki/index.php/DPF_with_AppoTech_AX206 For our german users, a very good explanation is found here: http://geekparadise.de/2011/04/digitaler-bilderrahmen-von-pearl-als-statusdisplay-fur-dockstar/ [/quote] So if you are not sure if you have the right DPF or something goes wrong: don't ask me ether - I'm like you only a user and not involved in the development of the hack! A guide how to hack the Pearl display can be found here (in german): http://www.vdr-portal.de/board1-news/board2-vdr-news/p1015287-announce-graphlcd-base-vdr-plugin-touchcol-branch/#post1015287