diff options
Diffstat (limited to 'linux/Documentation/video4linux/v4l2-framework.txt')
-rw-r--r-- | linux/Documentation/video4linux/v4l2-framework.txt | 45 |
1 files changed, 42 insertions, 3 deletions
diff --git a/linux/Documentation/video4linux/v4l2-framework.txt b/linux/Documentation/video4linux/v4l2-framework.txt index accc376e9..a31177390 100644 --- a/linux/Documentation/video4linux/v4l2-framework.txt +++ b/linux/Documentation/video4linux/v4l2-framework.txt @@ -91,7 +91,13 @@ NULL, then you *must* setup v4l2_dev->name before calling v4l2_device_register. The first 'dev' argument is normally the struct device pointer of a pci_dev, usb_device or platform_device. It is rare for dev to be NULL, but it happens -with ISA devices, for example. +with ISA devices or when one device creates multiple PCI devices, thus making +it impossible to associate v4l2_dev with a particular parent. + +You can also supply a notify() callback that can be called by sub-devices to +notify you of events. Whether you need to set this depends on the sub-device. +Any notifications a sub-device supports must be defined in a header in +include/media/<subdevice>.h. You unregister with: @@ -99,6 +105,17 @@ You unregister with: Unregistering will also automatically unregister all subdevs from the device. +If you have a hotpluggable device (e.g. a USB device), then when a disconnect +happens the parent device becomes invalid. Since v4l2_device has a pointer to +that parent device it has to be cleared as well to mark that the parent is +gone. To do this call: + + v4l2_device_disconnect(struct v4l2_device *v4l2_dev); + +This does *not* unregister the subdevs, so you still need to call the +v4l2_device_unregister() function for that. If your driver is not hotpluggable, +then there is no need to call v4l2_device_disconnect(). + Sometimes you need to iterate over all devices registered by a specific driver. This is usually the case if multiple device drivers use the same hardware. E.g. the ivtvfb driver is a framebuffer driver that uses the ivtv @@ -280,6 +297,11 @@ e.g. AUDIO_CONTROLLER and specify that as the group ID value when calling v4l2_device_call_all(). That ensures that it will only go to the subdev that needs it. +If the sub-device needs to notify its v4l2_device parent of an event, then +it can call v4l2_subdev_notify(sd, notification, arg). This macro checks +whether there is a notify() callback defined and returns -ENODEV if not. +Otherwise the result of the notify() call is returned. + The advantage of using v4l2_subdev is that it is a generic struct and does not contain any knowledge about the underlying hardware. So a driver might contain several subdevs that use an I2C bus, but also a subdev that is @@ -359,8 +381,8 @@ This loads the given module (can be NULL if no module needs to be loaded) and calls i2c_new_device() with the given i2c_adapter and chip/address arguments. If all goes well, then it registers the subdev with the v4l2_device. It gets the v4l2_device by calling i2c_get_adapdata(adapter), so you should make sure -that adapdata is set to v4l2_device when you setup the i2c_adapter in your -driver. +to call i2c_set_adapdata(adapter, v4l2_device) when you setup the i2c_adapter +in your driver. You can also use v4l2_i2c_new_probed_subdev() which is very similar to v4l2_i2c_new_subdev(), except that it has an array of possible I2C addresses @@ -368,6 +390,14 @@ that it should probe. Internally it calls i2c_new_probed_device(). Both functions return NULL if something went wrong. +Note that the chipid you pass to v4l2_i2c_new_(probed_)subdev() is usually +the same as the module name. It allows you to specify a chip variant, e.g. +"saa7114" or "saa7115". In general though the i2c driver autodetects this. +The use of chipid is something that needs to be looked at more closely at a +later date. It differs between i2c drivers and as such can be confusing. +To see which chip variants are supported you can look in the i2c driver code +for the i2c_device_id table. This lists all the possibilities. + struct video_device ------------------- @@ -406,6 +436,15 @@ You should also set these fields: - ioctl_ops: if you use the v4l2_ioctl_ops to simplify ioctl maintenance (highly recommended to use this and it might become compulsory in the future!), then set this to your v4l2_ioctl_ops struct. +- parent: you only set this if v4l2_device was registered with NULL as + the parent device struct. This only happens in cases where one hardware + device has multiple PCI devices that all share the same v4l2_device core. + + The cx88 driver is an example of this: one core v4l2_device struct, but + it is used by both an raw video PCI device (cx8800) and a MPEG PCI device + (cx8802). Since the v4l2_device cannot be associated with a particular + PCI device it is setup without a parent device. But when the struct + video_device is setup you do know which parent PCI device to use. If you use v4l2_ioctl_ops, then you should set either .unlocked_ioctl or .ioctl to video_ioctl2 in your v4l2_file_operations struct. |