diff options
Diffstat (limited to 'linux/drivers/media/video/cx18/cx18-driver.h')
| -rw-r--r-- | linux/drivers/media/video/cx18/cx18-driver.h | 48 |
1 files changed, 4 insertions, 44 deletions
diff --git a/linux/drivers/media/video/cx18/cx18-driver.h b/linux/drivers/media/video/cx18/cx18-driver.h index 26359897d..66cb74887 100644 --- a/linux/drivers/media/video/cx18/cx18-driver.h +++ b/linux/drivers/media/video/cx18/cx18-driver.h @@ -38,7 +38,6 @@ #include <linux/i2c-algo-bit.h> #include <linux/list.h> #include <linux/unistd.h> -#include <linux/byteorder/swab.h> #include <linux/pagemap.h> #include <linux/workqueue.h> #include <linux/mutex.h> @@ -64,6 +63,9 @@ # error "This driver requires kernel PCI support." #endif +/* Default delay to throttle mmio access to the CX23418 */ +#define CX18_DEFAULT_MMIO_NDELAY 0 /* 0 ns = 0 PCI clock(s) / 33 MHz */ + #define CX18_MEM_OFFSET 0x00000000 #define CX18_MEM_SIZE 0x04000000 #define CX18_REG_OFFSET 0x02000000 @@ -177,6 +179,7 @@ struct cx18_options { int cardtype; /* force card type on load */ int tuner; /* set tuner on load */ int radio; /* enable/disable radio */ + unsigned long mmio_ndelay; /* delay in ns after every PCI mmio access */ }; /* per-buffer bit flags */ @@ -458,47 +461,4 @@ void cx18_read_eeprom(struct cx18 *cx, struct tveeprom *tv); /* First-open initialization: load firmware, etc. */ int cx18_init_on_first_open(struct cx18 *cx); -/* This is a PCI post thing, where if the pci register is not read, then - the write doesn't always take effect right away. By reading back the - register any pending PCI writes will be performed (in order), and so - you can be sure that the writes are guaranteed to be done. - - Rarely needed, only in some timing sensitive cases. - Apparently if this is not done some motherboards seem - to kill the firmware and get into the broken state until computer is - rebooted. */ -#define write_sync(val, reg) \ - do { writel(val, reg); readl(reg); } while (0) - -#define read_reg(reg) readl(cx->reg_mem + (reg)) -#define write_reg(val, reg) writel(val, cx->reg_mem + (reg)) -#define write_reg_sync(val, reg) \ - do { write_reg(val, reg); read_reg(reg); } while (0) - -#define read_enc(addr) readl(cx->enc_mem + (u32)(addr)) -#define write_enc(val, addr) writel(val, cx->enc_mem + (u32)(addr)) -#define write_enc_sync(val, addr) \ - do { write_enc(val, addr); read_enc(addr); } while (0) - -#define sw1_irq_enable(val) do { \ - write_reg(val, SW1_INT_STATUS); \ - write_reg(read_reg(SW1_INT_ENABLE_PCI) | (val), SW1_INT_ENABLE_PCI); \ -} while (0) - -#define sw1_irq_disable(val) \ - write_reg(read_reg(SW1_INT_ENABLE_PCI) & ~(val), SW1_INT_ENABLE_PCI); - -#define sw2_irq_enable(val) do { \ - write_reg(val, SW2_INT_STATUS); \ - write_reg(read_reg(SW2_INT_ENABLE_PCI) | (val), SW2_INT_ENABLE_PCI); \ -} while (0) - -#define sw2_irq_disable(val) \ - write_reg(read_reg(SW2_INT_ENABLE_PCI) & ~(val), SW2_INT_ENABLE_PCI); - -#define setup_page(addr) do { \ - u32 val = read_reg(0xD000F8) & ~0x1f00; \ - write_reg(val | (((addr) >> 17) & 0x1f00), 0xD000F8); \ -} while (0) - #endif /* CX18_DRIVER_H */ |