diff options
Diffstat (limited to 'linux/drivers/media')
18 files changed, 112 insertions, 75 deletions
diff --git a/linux/drivers/media/common/saa7146_i2c.c b/linux/drivers/media/common/saa7146_i2c.c index 68674799b..fa9d4f90a 100644 --- a/linux/drivers/media/common/saa7146_i2c.c +++ b/linux/drivers/media/common/saa7146_i2c.c @@ -294,7 +294,6 @@ static int saa7146_i2c_transfer(struct saa7146_dev *dev, const struct i2c_msg *m int i = 0, count = 0; __le32 *buffer = dev->d_i2c.cpu_addr; int err = 0; - int address_err = 0; int short_delay = 0; if (mutex_lock_interruptible(&dev->i2c_lock)) @@ -334,17 +333,10 @@ static int saa7146_i2c_transfer(struct saa7146_dev *dev, const struct i2c_msg *m i2c address probing, however, and address errors indicate that a device is really *not* there. retrying in that case increases the time the device needs to probe greatly, so - it should be avoided. because of the fact, that only - analog based cards use irq based i2c transactions (for dvb - cards, this screwes up other interrupt sources), we bail out - completely for analog cards after an address error and trust - the saa7146 address error detection. */ - if ( -EREMOTEIO == err ) { - if( 0 != (SAA7146_USE_I2C_IRQ & dev->ext->flags)) { - goto out; - } - address_err++; - } + it should be avoided. So we bail out in irq mode after an + address error and trust the saa7146 address error detection. */ + if (-EREMOTEIO == err && 0 != (SAA7146_USE_I2C_IRQ & dev->ext->flags)) + goto out; DEB_I2C(("error while sending message(s). starting again.\n")); break; } @@ -359,10 +351,9 @@ static int saa7146_i2c_transfer(struct saa7146_dev *dev, const struct i2c_msg *m } while (err != num && retries--); - /* if every retry had an address error, exit right away */ - if (address_err == retries) { + /* quit if any error occurred */ + if (err != num) goto out; - } /* if any things had to be read, get the results */ if ( 0 != saa7146_i2c_msg_cleanup(msgs, num, buffer)) { diff --git a/linux/drivers/media/dvb/dvb-usb/Kconfig b/linux/drivers/media/dvb/dvb-usb/Kconfig index 3e581409f..3763a9c68 100644 --- a/linux/drivers/media/dvb/dvb-usb/Kconfig +++ b/linux/drivers/media/dvb/dvb-usb/Kconfig @@ -96,6 +96,7 @@ config DVB_USB_UMT_010 select DVB_PLL if !DVB_FE_CUSTOMISE select DVB_DIB3000MC select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMIZE + select DVB_MT352 if !DVB_FE_CUSTOMISE help Say Y here to support the HanfTek UMT-010 USB2.0 stick-sized DVB-T receiver. diff --git a/linux/drivers/media/dvb/frontends/stv0900_core.c b/linux/drivers/media/dvb/frontends/stv0900_core.c index c86c3017e..9ff9744a1 100644 --- a/linux/drivers/media/dvb/frontends/stv0900_core.c +++ b/linux/drivers/media/dvb/frontends/stv0900_core.c @@ -34,8 +34,8 @@ #include "stv0900_priv.h" #include "stv0900_init.h" -int debug = 1; -module_param(debug, int, 0644); +static int stvdebug = 1; +module_param_named(debug, stvdebug, int, 0644); /* internal params node */ struct stv0900_inode { diff --git a/linux/drivers/media/dvb/frontends/stv0900_priv.h b/linux/drivers/media/dvb/frontends/stv0900_priv.h index 28350fbeb..762d5af62 100644 --- a/linux/drivers/media/dvb/frontends/stv0900_priv.h +++ b/linux/drivers/media/dvb/frontends/stv0900_priv.h @@ -62,11 +62,11 @@ #define dmd_choose(a, b) (demod = STV0900_DEMOD_2 ? b : a)) -extern int debug; +static int stvdebug; #define dprintk(args...) \ do { \ - if (debug) \ + if (stvdebug) \ printk(KERN_DEBUG args); \ } while (0) diff --git a/linux/drivers/media/video/au0828/Kconfig b/linux/drivers/media/video/au0828/Kconfig index 621ec043f..deb00e4ac 100644 --- a/linux/drivers/media/video/au0828/Kconfig +++ b/linux/drivers/media/video/au0828/Kconfig @@ -5,9 +5,9 @@ config VIDEO_AU0828 select I2C_ALGOBIT select VIDEO_TVEEPROM select DVB_AU8522 if !DVB_FE_CUSTOMISE - select MEDIA_TUNER_XC5000 if !DVB_FE_CUSTOMIZE - select MEDIA_TUNER_MXL5007T if !DVB_FE_CUSTOMIZE - select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMIZE + select MEDIA_TUNER_XC5000 if !DVB_FE_CUSTOMISE + select MEDIA_TUNER_MXL5007T if !DVB_FE_CUSTOMISE + select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMISE ---help--- This is a video4linux driver for Auvitek's USB device. diff --git a/linux/drivers/media/video/cx18/cx18-audio.c b/linux/drivers/media/video/cx18/cx18-audio.c index ccd170887..bb5c5165d 100644 --- a/linux/drivers/media/video/cx18/cx18-audio.c +++ b/linux/drivers/media/video/cx18/cx18-audio.c @@ -24,6 +24,7 @@ #include "cx18-driver.h" #include "cx18-io.h" #include "cx18-cards.h" +#include "cx18-audio.h" #define CX18_AUDIO_ENABLE 0xc72014 diff --git a/linux/drivers/media/video/cx18/cx18-av-core.c b/linux/drivers/media/video/cx18/cx18-av-core.c index cf256a999..21f4be839 100644 --- a/linux/drivers/media/video/cx18/cx18-av-core.c +++ b/linux/drivers/media/video/cx18/cx18-av-core.c @@ -292,23 +292,29 @@ void cx18_av_std_setup(struct cx18 *cx) * * vsync: always 6 half-lines of vsync pulses * vactive: half lines of active video - * vblank656: half lines, after line 3, of blanked video - * vblank: half lines, after line 9, of blanked video + * vblank656: half lines, after line 3/mid-266, of blanked video + * vblank: half lines, after line 9/272, of blanked video * + * As far as I can tell: * vblank656 starts counting from the falling edge of the first - * vsync pulse (start of line 4) + * vsync pulse (start of line 4 or mid-266) * vblank starts counting from the after the 6 vsync pulses and - * 6 equalization pulses (start of line 10) + * 6 or 5 equalization pulses (start of line 10 or 272) * * For 525 line systems the driver will extract VBI information - * from lines 10 through 21. To avoid the EAV RP code from - * toggling at the start of hblank at line 22, where sliced VBI - * data from line 21 is stuffed, also treat line 22 as blanked. + * from lines 10-21 and lines 273-284. */ - vblank656 = 38; /* lines 4 through 22 */ - vblank = 26; /* lines 10 through 22 */ - vactive = 481; /* lines 23 through 262.5 */ + vblank656 = 38; /* lines 4 - 22 & 266 - 284 */ + vblank = 26; /* lines 10 - 22 & 272 - 284 */ + vactive = 481; /* lines 23 - 263 & 285 - 525 */ + /* + * For a 13.5 Mpps clock and 15,734.26 Hz line rate, a line is + * is 858 pixels = 720 active + 138 blanking. The Hsync leading + * edge should happen 1.2 us * 13.5 Mpps ~= 16 pixels after the + * end of active video, leaving 122 pixels of hblank to ignore + * before active video starts. + */ hactive = 720; hblank = 122; luma_lpf = 1; @@ -867,8 +873,22 @@ static int cx18_av_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt) Hsrc = (cx18_av_read(cx, 0x472) & 0x3f) << 4; Hsrc |= (cx18_av_read(cx, 0x471) & 0xf0) >> 4; - Vlines = pix->height + (is_50Hz ? 4 : 7); + /* + * This adjustment reflects the excess of vactive, set in + * cx18_av_std_setup(), above standard values: + * + * 480 + 1 for 60 Hz systems + * 576 + 4 for 50 Hz systems + */ + Vlines = pix->height + (is_50Hz ? 4 : 1); + /* + * Invalid height and width scaling requests are: + * 1. width less than 1/16 of the source width + * 2. width greater than the source width + * 3. height less than 1/8 of the source height + * 4. height greater than the source height + */ if ((pix->width * 16 < Hsrc) || (Hsrc < pix->width) || (Vlines * 8 < Vsrc) || (Vsrc < Vlines)) { CX18_ERR_DEV(sd, "%dx%d is not a valid size!\n", diff --git a/linux/drivers/media/video/cx18/cx18-av-core.h b/linux/drivers/media/video/cx18/cx18-av-core.h index fd0df4151..2687a2c91 100644 --- a/linux/drivers/media/video/cx18/cx18-av-core.h +++ b/linux/drivers/media/video/cx18/cx18-av-core.h @@ -89,16 +89,21 @@ struct cx18_av_state { /* * The VBI slicer starts operating and counting lines, begining at - * slicer line count of 1, at D lines after the deassertion of VRESET - * This staring field line, S, is 6 or 10 for 625 or 525 line systems. - * Sliced ancillary data captured on VBI slicer line M is sent at the - * beginning of the next VBI slicer line, VBI slicer line count N = M+1. - * Thus when the VBI slicer reports a VBI slicer line number with - * ancillary data, the IDID0 byte indicates VBI slicer line N. - * The actual field line that the captured data comes from is + * slicer line count of 1, at D lines after the deassertion of VRESET. + * This staring field line, S, is 6 (& 319) or 10 (& 273) for 625 or 525 + * line systems respectively. Sliced ancillary data captured on VBI + * slicer line M is inserted after the VBI slicer is done with line M, + * when VBI slicer line count is N = M+1. Thus when the VBI slicer + * reports a VBI slicer line number with ancillary data, the IDID0 byte + * indicates VBI slicer line N. The actual field line that the captured + * data comes from is + * * L = M+(S+D-1) = N-1+(S+D-1) = N + (S+D-2). * + * L is the line in the field, not frame, from which the VBI data came. + * N is the line reported by the slicer in the ancillary data. * D is the slicer_line_delay value programmed into register 0x47f. + * S is 6 for 625 line systems or 10 for 525 line systems * (S+D-2) is the slicer_line_offset used to convert slicer reported * line counts to actual field lines. */ diff --git a/linux/drivers/media/video/cx18/cx18-av-vbi.c b/linux/drivers/media/video/cx18/cx18-av-vbi.c index 43267d1af..27699839b 100644 --- a/linux/drivers/media/video/cx18/cx18-av-vbi.c +++ b/linux/drivers/media/video/cx18/cx18-av-vbi.c @@ -142,7 +142,7 @@ int cx18_av_vbi(struct cx18 *cx, unsigned int cmd, void *arg) 0, V4L2_SLICED_TELETEXT_B, 0, /* 1 */ 0, V4L2_SLICED_WSS_625, 0, /* 4 */ V4L2_SLICED_CAPTION_525, /* 6 */ - V4L2_SLICED_VPS, 0, 0, 0, 0, /* 7 - unlike cx25840 */ + 0, 0, V4L2_SLICED_VPS, 0, 0, /* 9 */ 0, 0, 0, 0 }; int is_pal = !(state->std & V4L2_STD_525_60); @@ -243,7 +243,7 @@ int cx18_av_vbi(struct cx18 *cx, unsigned int cmd, void *arg) lcr[i] |= 6 << (4 * x); break; case V4L2_SLICED_VPS: - lcr[i] |= 7 << (4 * x); /*'840 differs*/ + lcr[i] |= 9 << (4 * x); break; } } @@ -301,7 +301,7 @@ int cx18_av_vbi(struct cx18 *cx, unsigned int cmd, void *arg) sdid = V4L2_SLICED_CAPTION_525; err = !odd_parity(p[0]) || !odd_parity(p[1]); break; - case 7: /* Differs from cx25840 */ + case 9: sdid = V4L2_SLICED_VPS; if (decode_vps(p, p) != 0) err = 1; diff --git a/linux/drivers/media/video/cx18/cx18-controls.c b/linux/drivers/media/video/cx18/cx18-controls.c index 925e01fdb..82fc2f9d4 100644 --- a/linux/drivers/media/video/cx18/cx18-controls.c +++ b/linux/drivers/media/video/cx18/cx18-controls.c @@ -166,15 +166,26 @@ static int cx18_g_ctrl(struct cx18 *cx, struct v4l2_control *vctrl) return 0; } -static int cx18_setup_vbi_fmt(struct cx18 *cx, enum v4l2_mpeg_stream_vbi_fmt fmt) +static int cx18_setup_vbi_fmt(struct cx18 *cx, + enum v4l2_mpeg_stream_vbi_fmt fmt, + enum v4l2_mpeg_stream_type type) { if (!(cx->v4l2_cap & V4L2_CAP_SLICED_VBI_CAPTURE)) return -EINVAL; if (atomic_read(&cx->ana_capturing) > 0) return -EBUSY; - /* First try to allocate sliced VBI buffers if needed. */ - if (fmt && cx->vbi.sliced_mpeg_data[0] == NULL) { + if (fmt != V4L2_MPEG_STREAM_VBI_FMT_IVTV || + type != V4L2_MPEG_STREAM_TYPE_MPEG2_PS) { + /* We don't do VBI insertion aside from IVTV format in a PS */ + cx->vbi.insert_mpeg = V4L2_MPEG_STREAM_VBI_FMT_NONE; + CX18_DEBUG_INFO("disabled insertion of sliced VBI data into " + "the MPEG stream\n"); + return 0; + } + + /* Allocate sliced VBI buffers if needed. */ + if (cx->vbi.sliced_mpeg_data[0] == NULL) { int i; for (i = 0; i < CX18_VBI_FRAMES; i++) { @@ -185,19 +196,27 @@ static int cx18_setup_vbi_fmt(struct cx18 *cx, enum v4l2_mpeg_stream_vbi_fmt fmt kfree(cx->vbi.sliced_mpeg_data[i]); cx->vbi.sliced_mpeg_data[i] = NULL; } + cx->vbi.insert_mpeg = + V4L2_MPEG_STREAM_VBI_FMT_NONE; + CX18_WARN("Unable to allocate buffers for " + "sliced VBI data insertion\n"); return -ENOMEM; } } } cx->vbi.insert_mpeg = fmt; + CX18_DEBUG_INFO("enabled insertion of sliced VBI data into the MPEG PS," + "when sliced VBI is enabled\n"); - if (cx->vbi.insert_mpeg == 0) - return 0; - /* Need sliced data for mpeg insertion */ + /* + * If our current settings have no lines set for capture, store a valid, + * default set of service lines to capture, in our current settings. + */ if (cx18_get_service_set(cx->vbi.sliced_in) == 0) { if (cx->is_60hz) - cx->vbi.sliced_in->service_set = V4L2_SLICED_CAPTION_525; + cx->vbi.sliced_in->service_set = + V4L2_SLICED_CAPTION_525; else cx->vbi.sliced_in->service_set = V4L2_SLICED_WSS_625; cx18_expand_service_set(cx->vbi.sliced_in, cx->is_50hz); @@ -284,8 +303,11 @@ int cx18_s_ext_ctrls(struct file *file, void *fh, struct v4l2_ext_controls *c) priv.cx = cx; priv.s = &cx->streams[id->type]; err = cx2341x_update(&priv, cx18_api_func, &cx->params, &p); - if (!err && cx->params.stream_vbi_fmt != p.stream_vbi_fmt) - err = cx18_setup_vbi_fmt(cx, p.stream_vbi_fmt); + if (!err && + (cx->params.stream_vbi_fmt != p.stream_vbi_fmt || + cx->params.stream_type != p.stream_type)) + err = cx18_setup_vbi_fmt(cx, p.stream_vbi_fmt, + p.stream_type); cx->params = p; cx->dualwatch_stereo_mode = p.audio_properties & 0x0300; idx = p.audio_properties & 0x03; diff --git a/linux/drivers/media/video/cx18/cx18-driver.c b/linux/drivers/media/video/cx18/cx18-driver.c index 8f294f436..f688ec7db 100644 --- a/linux/drivers/media/video/cx18/cx18-driver.c +++ b/linux/drivers/media/video/cx18/cx18-driver.c @@ -273,8 +273,7 @@ void cx18_read_eeprom(struct cx18 *cx, struct tveeprom *tv) u8 eedata[256]; memset(&c, 0, sizeof(c)); - strncpy(c.name, "cx18 tveeprom tmp", sizeof(c.name)); - c.name[sizeof(c.name)-1] = '\0'; + strlcpy(c.name, "cx18 tveeprom tmp", sizeof(c.name)); c.adapter = &cx->i2c_adap[0]; c.addr = 0xA0 >> 1; diff --git a/linux/drivers/media/video/cx18/cx18-streams.c b/linux/drivers/media/video/cx18/cx18-streams.c index 0605c2d83..7c1db9c18 100644 --- a/linux/drivers/media/video/cx18/cx18-streams.c +++ b/linux/drivers/media/video/cx18/cx18-streams.c @@ -413,9 +413,8 @@ static void cx18_vbi_setup(struct cx18_stream *s) * 0x90 (Task HorizontalBlank) * 0xd0 (Task EvenField HorizontalBlank) * - * We have set the digitzer to consider the first active line - * as part of VerticalBlank as well so we don't have to look for - * these problem codes nor lose the last line of sliced data. + * We have set the digitzer such that we don't have to worry + * about these problem codes. */ data[4] = 0xB0F0B0F0; /* diff --git a/linux/drivers/media/video/cx18/cx18-vbi.c b/linux/drivers/media/video/cx18/cx18-vbi.c index a81fe2e98..355737bff 100644 --- a/linux/drivers/media/video/cx18/cx18-vbi.c +++ b/linux/drivers/media/video/cx18/cx18-vbi.c @@ -169,7 +169,7 @@ void cx18_process_vbi_data(struct cx18 *cx, struct cx18_buffer *buf, int streamtype) { u8 *p = (u8 *) buf->buf; - u32 *q = (u32 *) buf->buf; + __be32 *q = (__be32 *) buf->buf; u32 size = buf->bytesused; u32 pts; int lines; @@ -178,8 +178,9 @@ void cx18_process_vbi_data(struct cx18 *cx, struct cx18_buffer *buf, return; /* - * The CX23418 sends us data that is 32 bit LE swapped, but we want - * the raw VBI bytes in the order they were in the raster line + * The CX23418 sends us data that is 32 bit little-endian swapped, + * but we want the raw VBI bytes in the order they were in the raster + * line. This has a side effect of making the 12 byte header big endian */ cx18_buf_swap(buf); @@ -218,7 +219,7 @@ void cx18_process_vbi_data(struct cx18 *cx, struct cx18_buffer *buf, /* Sliced VBI data with data insertion */ - pts = (be32_to_cpu(q[0] == 0x3fffffff)) ? be32_to_cpu(q[2]) : 0; + pts = (be32_to_cpu(q[0]) == 0x3fffffff) ? be32_to_cpu(q[2]) : 0; /* * For calls to compress_sliced_buf(), ensure there are an integral diff --git a/linux/drivers/media/video/cx23885/Kconfig b/linux/drivers/media/video/cx23885/Kconfig index 4066ca69c..28896aa31 100644 --- a/linux/drivers/media/video/cx23885/Kconfig +++ b/linux/drivers/media/video/cx23885/Kconfig @@ -20,10 +20,10 @@ config VIDEO_CX23885 select DVB_STV6110 if !DVB_FE_CUSTOMISE select DVB_STV0900 if !DVB_FE_CUSTOMISE select MEDIA_TUNER_MT2131 if !MEDIA_TUNER_CUSTOMIZE - select MEDIA_TUNER_XC2028 if !DVB_FE_CUSTOMIZE - select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMIZE - select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMIZE - select MEDIA_TUNER_XC5000 if !DVB_FE_CUSTOMIZE + select MEDIA_TUNER_XC2028 if !DVB_FE_CUSTOMISE + select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMISE + select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMISE + select MEDIA_TUNER_XC5000 if !DVB_FE_CUSTOMISE ---help--- This is a video4linux driver for Conexant 23885 based TV cards. diff --git a/linux/drivers/media/video/em28xx/em28xx-dvb.c b/linux/drivers/media/video/em28xx/em28xx-dvb.c index c76dbc029..edafe9bde 100644 --- a/linux/drivers/media/video/em28xx/em28xx-dvb.c +++ b/linux/drivers/media/video/em28xx/em28xx-dvb.c @@ -30,9 +30,6 @@ #include "lgdt330x.h" #include "zl10353.h" #include "s5h1409.h" -#ifdef EM28XX_DRX397XD_SUPPORT -#include "drx397xD.h" -#endif MODULE_DESCRIPTION("driver for em28xx based DVB cards"); MODULE_AUTHOR("Mauro Carvalho Chehab <mchehab@infradead.org>"); diff --git a/linux/drivers/media/video/pvrusb2/Kconfig b/linux/drivers/media/video/pvrusb2/Kconfig index 7f7b05c40..bb4271393 100644 --- a/linux/drivers/media/video/pvrusb2/Kconfig +++ b/linux/drivers/media/video/pvrusb2/Kconfig @@ -41,9 +41,9 @@ config VIDEO_PVRUSB2_DVB select DVB_S5H1409 if !DVB_FE_CUSTOMISE select DVB_S5H1411 if !DVB_FE_CUSTOMISE select DVB_TDA10048 if !DVB_FE_CUSTOMISE - select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMIZE + select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMISE select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE - select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMIZE + select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMISE ---help--- This option enables a DVB interface for the pvrusb2 driver. diff --git a/linux/drivers/media/video/saa7134/Kconfig b/linux/drivers/media/video/saa7134/Kconfig index e69d504ac..51f17c82b 100644 --- a/linux/drivers/media/video/saa7134/Kconfig +++ b/linux/drivers/media/video/saa7134/Kconfig @@ -40,6 +40,8 @@ config VIDEO_SAA7134_DVB select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE select DVB_ZL10036 if !DVB_FE_CUSTOMISE select DVB_MT312 if !DVB_FE_CUSTOMISE + select DVB_LNBP21 if !DVB_FE_CUSTOMISE + select DVB_ZL10353 if !DVB_FE_CUSTOMISE ---help--- This adds support for DVB cards based on the Philips saa7134 chip. diff --git a/linux/drivers/media/video/zoran/zoran_driver.c b/linux/drivers/media/video/zoran/zoran_driver.c index 8eda83b06..1560c1e4c 100644 --- a/linux/drivers/media/video/zoran/zoran_driver.c +++ b/linux/drivers/media/video/zoran/zoran_driver.c @@ -1378,11 +1378,10 @@ setup_overlay (struct file *file, /* get the status of a buffer in the clients buffer queue */ static int -zoran_v4l2_buffer_status (struct file *file, +zoran_v4l2_buffer_status (struct zoran_fh *fh, struct v4l2_buffer *buf, int num) { - struct zoran_fh *fh = file->private_data; struct zoran *zr = fh->zr; buf->flags = V4L2_BUF_FLAG_MAPPED; @@ -2502,7 +2501,7 @@ static int zoran_querybuf(struct file *file, void *__fh, struct v4l2_buffer *buf int res; mutex_lock(&zr->resource_lock); - res = zoran_v4l2_buffer_status(file, buf, buf->index); + res = zoran_v4l2_buffer_status(fh, buf, buf->index); mutex_unlock(&zr->resource_lock); return res; @@ -2603,7 +2602,7 @@ static int zoran_dqbuf(struct file *file, void *__fh, struct v4l2_buffer *buf) if (res) goto dqbuf_unlock_and_return; zr->v4l_sync_tail++; - res = zoran_v4l2_buffer_status(file, buf, num); + res = zoran_v4l2_buffer_status(fh, buf, num); break; case ZORAN_MAP_MODE_JPG_REC: @@ -2634,7 +2633,7 @@ static int zoran_dqbuf(struct file *file, void *__fh, struct v4l2_buffer *buf) res = jpg_sync(file, &bs); if (res) goto dqbuf_unlock_and_return; - res = zoran_v4l2_buffer_status(file, buf, bs.frame); + res = zoran_v4l2_buffer_status(fh, buf, bs.frame); break; } |