diff options
Diffstat (limited to 'linux')
| -rwxr-xr-x | linux/Documentation/dvb/get_dvb_firmware | 52 | ||||
| -rw-r--r-- | linux/drivers/media/video/cx18/cx18-cards.c | 34 | ||||
| -rw-r--r-- | linux/drivers/media/video/cx18/cx18-dvb.c | 160 |
3 files changed, 233 insertions, 13 deletions
diff --git a/linux/Documentation/dvb/get_dvb_firmware b/linux/Documentation/dvb/get_dvb_firmware index a52adfc9a..64174d625 100755 --- a/linux/Documentation/dvb/get_dvb_firmware +++ b/linux/Documentation/dvb/get_dvb_firmware @@ -25,7 +25,7 @@ use IO::Handle; "tda10046lifeview", "av7110", "dec2000t", "dec2540t", "dec3000s", "vp7041", "dibusb", "nxt2002", "nxt2004", "or51211", "or51132_qam", "or51132_vsb", "bluebird", - "opera1", "cx231xx", "cx18", "cx23885", "pvrusb2" ); + "opera1", "cx231xx", "cx18", "cx23885", "pvrusb2", "mpc718" ); # Check args syntax() if (scalar(@ARGV) != 1); @@ -381,6 +381,56 @@ sub cx18 { $allfiles; } +sub mpc718 { + my $archive = 'Yuan MPC718 TV Tuner Card 2.13.10.1016.zip'; + my $url = "ftp://ftp.work.acer-euro.com/desktop/aspire_idea510/vista/Drivers/$archive"; + my $fwfile = "dvb-cx18-mpc718-mt352.fw"; + my $tmpdir = tempdir(DIR => "/tmp", CLEANUP => 1); + + checkstandard(); + wgetfile($archive, $url); + unzip($archive, $tmpdir); + + my $sourcefile = "$tmpdir/Yuan MPC718 TV Tuner Card 2.13.10.1016/mpc718_32bit/yuanrap.sys"; + my $found = 0; + + open IN, '<', $sourcefile or die "Couldn't open $sourcefile to extract $fwfile data\n"; + binmode IN; + open OUT, '>', $fwfile; + binmode OUT; + { + # Block scope because we change the line terminator variable $/ + my $prevlen = 0; + my $currlen; + + # Buried in the data segment are 3 runs of almost identical + # register-value pairs that end in 0x5d 0x01 which is a "TUNER GO" + # command for the MT352. + # Pull out the middle run (because it's easy) of register-value + # pairs to make the "firmware" file. + + local $/ = "\x5d\x01"; # MT352 "TUNER GO" + + while (<IN>) { + $currlen = length($_); + if ($prevlen == $currlen || $currlen <= 64) { + chop; chop; # Get rid of "TUNER GO" + s/^\0\0//; # get rid of leading 00 00 if it's there + printf OUT "$_"; + $found = 1; + last; + } + } + } + close OUT; + close IN; + if (!$found) { + unlink $fwfile; + die "Couldn't find valid register-value sequence in $sourcefile for $fwfile\n"; + } + $fwfile; +} + sub cx23885 { my $url = "http://linuxtv.org/downloads/firmware/"; diff --git a/linux/drivers/media/video/cx18/cx18-cards.c b/linux/drivers/media/video/cx18/cx18-cards.c index fa755a982..d9a407681 100644 --- a/linux/drivers/media/video/cx18/cx18-cards.c +++ b/linux/drivers/media/video/cx18/cx18-cards.c @@ -198,11 +198,14 @@ static const struct cx18_card_pci_info cx18_pci_mpc718[] = { static const struct cx18_card cx18_card_mpc718 = { .type = CX18_CARD_YUAN_MPC718, - .name = "Yuan MPC718", - .comment = "Analog video capture works; some audio line in may not.\n", + .name = "Yuan MPC718 MiniPCI DVB-T/Analog", + .comment = "Experimenters needed for device to work well.\n" + "\tTo help, mail the ivtv-devel list (www.ivtvdriver.org).\n", .v4l2_capabilities = CX18_CAP_ENCODER, .hw_audio_ctrl = CX18_HW_418_AV, - .hw_all = CX18_HW_418_AV | CX18_HW_TUNER | CX18_HW_GPIO_RESET_CTRL, + .hw_muxer = CX18_HW_GPIO_MUX, + .hw_all = CX18_HW_418_AV | CX18_HW_TUNER | + CX18_HW_GPIO_MUX | CX18_HW_DVB | CX18_HW_GPIO_RESET_CTRL, .video_inputs = { { CX18_CARD_INPUT_VID_TUNER, 0, CX18_AV_COMPOSITE2 }, { CX18_CARD_INPUT_SVIDEO1, 1, @@ -211,27 +214,34 @@ static const struct cx18_card cx18_card_mpc718 = { { CX18_CARD_INPUT_SVIDEO2, 2, CX18_AV_SVIDEO_LUMA7 | CX18_AV_SVIDEO_CHROMA8 }, { CX18_CARD_INPUT_COMPOSITE2, 2, CX18_AV_COMPOSITE6 }, - { CX18_CARD_INPUT_COMPOSITE3, 2, CX18_AV_COMPOSITE3 }, }, .audio_inputs = { { CX18_CARD_INPUT_AUD_TUNER, CX18_AV_AUDIO5, 0 }, - { CX18_CARD_INPUT_LINE_IN1, CX18_AV_AUDIO_SERIAL1, 0 }, - { CX18_CARD_INPUT_LINE_IN2, CX18_AV_AUDIO_SERIAL1, 0 }, + { CX18_CARD_INPUT_LINE_IN1, CX18_AV_AUDIO_SERIAL1, 1 }, + { CX18_CARD_INPUT_LINE_IN2, CX18_AV_AUDIO_SERIAL2, 1 }, }, - .radio_input = { CX18_CARD_INPUT_AUD_TUNER, CX18_AV_AUDIO_SERIAL1, 0 }, .tuners = { /* XC3028 tuner */ { .std = V4L2_STD_ALL, .tuner = TUNER_XC2028 }, }, + /* FIXME - the FM radio is just a guess and driver doesn't use SIF */ + .radio_input = { CX18_CARD_INPUT_AUD_TUNER, CX18_AV_AUDIO5, 2 }, .ddr = { - /* Probably Samsung K4D263238G-VC33 memory */ - .chip_config = 0x003, - .refresh = 0x30c, - .timing1 = 0x23230b73, - .timing2 = 0x08, + /* Hynix HY5DU283222B DDR RAM */ + .chip_config = 0x303, + .refresh = 0x3bd, + .timing1 = 0x36320966, + .timing2 = 0x1f, .tune_lane = 0, .initial_emrs = 2, }, + .gpio_init.initial_value = 0x1, + .gpio_init.direction = 0x3, + /* FIXME - these GPIO's are just guesses */ + .gpio_audio_input = { .mask = 0x3, + .tuner = 0x1, + .linein = 0x3, + .radio = 0x1 }, .xceive_pin = 0, .pci_list = cx18_pci_mpc718, .i2c = &cx18_i2c_std, diff --git a/linux/drivers/media/video/cx18/cx18-dvb.c b/linux/drivers/media/video/cx18/cx18-dvb.c index 6ea3fe623..51a0c33b2 100644 --- a/linux/drivers/media/video/cx18/cx18-dvb.c +++ b/linux/drivers/media/video/cx18/cx18-dvb.c @@ -30,6 +30,10 @@ #include "s5h1409.h" #include "mxl5005s.h" #include "zl10353.h" + +#include <linux/firmware.h> +#include "mt352.h" +#include "mt352_priv.h" #include "tuner-xc2028.h" DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); @@ -38,6 +42,11 @@ DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr); #define CX18_CLOCK_ENABLE2 0xc71024 #define CX18_DMUX_CLK_MASK 0x0080 +/* + * CX18_CARD_HVR_1600_ESMT + * CX18_CARD_HVR_1600_SAMSUNG + */ + static struct mxl5005s_config hauppauge_hvr1600_tuner = { .i2c_address = 0xC6 >> 1, .if_freq = IF_FREQ_5380000HZ, @@ -65,6 +74,9 @@ static struct s5h1409_config hauppauge_hvr1600_config = { .mpeg_timing = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK }; +/* + * CX18_CARD_LEADTEK_DVR3100H + */ /* Information/confirmation of proper config values provided by Terry Wu */ static struct zl10353_config leadtek_dvr3100h_demod = { .demod_address = 0x1e >> 1, /* Datasheet suggested straps */ @@ -74,6 +86,121 @@ static struct zl10353_config leadtek_dvr3100h_demod = { .disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */ }; +/* + * CX18_CARD_YUAN_MPC718 + */ +/* + * Due to + * + * 1. an absence of information on how to prgram the MT352 + * 2. the Linux mt352 module pushing MT352 initialzation off onto us here + * + * We have to use an init sequence that *you* must extract from the Windows + * driver (yuanrap.sys) and which we load as a firmware. + * + * If someone can provide me with a Zarlink MT352 (Intel CE6352?) Design Manual + * with chip programming details, then I can remove this annoyance. + */ +static int yuan_mpc718_mt352_reqfw(struct cx18_stream *stream, + const struct firmware **fw) +{ + struct cx18 *cx = stream->cx; + const char *fn = "dvb-cx18-mpc718-mt352.fw"; + int ret; + + ret = request_firmware(fw, fn, &cx->pci_dev->dev); + if (ret) + CX18_ERR("Unable to open firmware file %s\n", fn); + else { + size_t sz = (*fw)->size; + if (sz < 2 || sz > 64 || (sz % 2) != 0) { + CX18_ERR("Firmware %s has a bad size: %lu bytes\n", + fn, (unsigned long) sz); + ret = -EILSEQ; + release_firmware(*fw); + *fw = NULL; + } + } + + if (ret) { + CX18_ERR("The MPC718 board variant with the MT352 DVB-T" + "demodualtor will not work without it\n"); + CX18_ERR("Run 'linux/Documentation/dvb/get_dvb_firmware " + "mpc718' if you need the firmware\n"); + } + return ret; +} + +static int yuan_mpc718_mt352_init(struct dvb_frontend *fe) +{ + struct cx18_dvb *dvb = container_of(fe->dvb, + struct cx18_dvb, dvb_adapter); + struct cx18_stream *stream = container_of(dvb, struct cx18_stream, dvb); + const struct firmware *fw = NULL; + int ret; + int i; + u8 buf[3]; + + ret = yuan_mpc718_mt352_reqfw(stream, &fw); + if (ret) + return ret; + + /* Loop through all the register-value pairs in the firmware file */ + for (i = 0; i < fw->size; i += 2) { + buf[0] = fw->data[i]; + /* Intercept a few registers we want to set ourselves */ + switch (buf[0]) { + case TRL_NOMINAL_RATE_0: + /* Set our custom OFDM bandwidth in the case below */ + break; + case TRL_NOMINAL_RATE_1: + /* 6 MHz: 64/7 * 6/8 / 20.48 * 2^16 = 0x55b6.db6 */ + /* 7 MHz: 64/7 * 7/8 / 20.48 * 2^16 = 0x6400 */ + /* 8 MHz: 64/7 * 8/8 / 20.48 * 2^16 = 0x7249.249 */ + buf[1] = 0x72; + buf[2] = 0x49; + mt352_write(fe, buf, 3); + break; + case INPUT_FREQ_0: + /* Set our custom IF in the case below */ + break; + case INPUT_FREQ_1: + /* 4.56 MHz IF: (20.48 - 4.56)/20.48 * 2^14 = 0x31c0 */ + buf[1] = 0x31; + buf[2] = 0xc0; + mt352_write(fe, buf, 3); + break; + default: + /* Pass through the register-value pair from the fw */ + buf[1] = fw->data[i+1]; + mt352_write(fe, buf, 2); + break; + } + } + + buf[0] = (u8) TUNER_GO; + buf[1] = 0x01; /* Go */ + mt352_write(fe, buf, 2); + release_firmware(fw); + return 0; +} + +static struct mt352_config yuan_mpc718_mt352_demod = { + .demod_address = 0x1e >> 1, + .adc_clock = 20480, /* 20.480 MHz */ + .if2 = 4560, /* 4.560 MHz */ + .no_tuner = 1, /* XC3028 is not behind the gate */ + .demod_init = yuan_mpc718_mt352_init, +}; + +static struct zl10353_config yuan_mpc718_zl10353_demod = { + .demod_address = 0x1e >> 1, /* Datasheet suggested straps */ + .if2 = 45600, /* 4.560 MHz IF from the XC3028 */ + .parallel_ts = 1, /* Not a serial TS */ + .no_tuner = 1, /* XC3028 is not behind the gate */ + .disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */ +}; + static int dvb_register(struct cx18_stream *stream); /* Kernel DVB framework calls this when the feed needs to start. @@ -113,6 +240,7 @@ static int cx18_dvb_start_feed(struct dvb_demux_feed *feed) break; case CX18_CARD_LEADTEK_DVR3100H: + case CX18_CARD_YUAN_MPC718: default: /* Assumption - Parallel transport - Signalling * undefined or default. @@ -326,6 +454,38 @@ static int dvb_register(struct cx18_stream *stream) fe->ops.tuner_ops.set_config(fe, &ctrl); } break; + case CX18_CARD_YUAN_MPC718: + /* + * TODO + * Apparently, these cards also could instead have a + * DiBcom demod supported by one of the db7000 drivers + */ + dvb->fe = dvb_attach(mt352_attach, + &yuan_mpc718_mt352_demod, + &cx->i2c_adap[1]); + if (dvb->fe == NULL) + dvb->fe = dvb_attach(zl10353_attach, + &yuan_mpc718_zl10353_demod, + &cx->i2c_adap[1]); + if (dvb->fe != NULL) { + struct dvb_frontend *fe; + struct xc2028_config cfg = { + .i2c_adap = &cx->i2c_adap[1], + .i2c_addr = 0xc2 >> 1, + .ctrl = NULL, + }; + static struct xc2028_ctrl ctrl = { + .fname = XC2028_DEFAULT_FIRMWARE, + .max_len = 64, + .demod = XC3028_FE_ZARLINK456, + .type = XC2028_AUTO, + }; + + fe = dvb_attach(xc2028_attach, dvb->fe, &cfg); + if (fe != NULL && fe->ops.tuner_ops.set_config != NULL) + fe->ops.tuner_ops.set_config(fe, &ctrl); + } + break; default: /* No Digital Tv Support */ break; |