| Age | Commit message (Collapse) | Author |
|---|
|
From: Devin Heitmueller <devin.heitmueller@gmail.com>
Make return value checking for calls to i2c routines explicit.
Priority: normal
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Devin Heitmueller <devin.heitmueller@gmail.com>
Cleanup the i2c write routine, getting rid of a passthrough function with only
one caller
Priority: normal
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Devin Heitmueller <devin.heitmueller@gmail.com>
This patch centralizes the i2c read functions, and eliminates pass-through
function only called by one caller.
Make reading of xc5000 registers an atomic i2c transaction in case we're on a
multi-master bus.
Priority: normal
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Devin Heitmueller <devin.heitmueller@gmail.com>
Properly handle tuner reset failures (before it was always returning success)
Priority: normal
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Dmitri Belimov <d.belimov@gmail.com>
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean Delvare <khali@linux-fr.org>
Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.
I may have missed other drivers which need the same fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
kernel-sync:
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: klaas de waal <klaas.de.waal@gmail.com>
Separate tuning table for DVB-C solves tuning problem at 388MHz
TechnoTrend C-1501 DVB-C card does not lock on 388MHz. I assume that
existing frequency table is valid for DVB-T.
This is suggested by the name of the table: tda827xa_dvbt.
Added a table for DVB-C with the name tda827xa_dvbc.
Added runtime selection of the DVB-C table when the tuner is type
FE_QAM.
This should leave the behaviour of this driver with with DVB_T tuners
unchanged. This modification is in file tda827x.c
The tda827x.c gives the following warning message when debug=1:
tda827x: tda827x_config not defined, cannot set LNA gain!
Solved this by adding a tda827x_config struct in budget-ci.c.
Priority: normal
Signed-off-by: Klaas de Waal <klaas.de.waal@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Andy Walls <awalls@radix.net>
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several Kconfig items using CUSTOMIZE. Yet, most use the English
writing CUSTOMISE. This generates lots of trouble, because people sometimes type
the Kbuild item different.
Let's standardise every occurrence using the same syntax.
The changes were generated by this small shell script:
for i in `find linux -type f`; do sed s,CUSTOMIZE,CUSTOMISE,g $i >/tmp/a && mv /tmp/a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@linuxtv.org>
The xc5000 driver has a bug where the IF is always set to whatever the first
caller to dvb_attach() provides. This fails when the device requires an IF
other than 5380 and the analog driver is loaded first through tuner-core
(which always supplies the hard-coded value of 5380).
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
tuner-xc3028 can be put to sleep to save power. However, if not properly
recovered from sleep, the device won't work. It is noticed that some
devices doesn't recover properly, so let's add a dump_stack() as a debug
option, to allow us to track when this happens.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@linuxtv.org>
The init_fw option was broken for the HVR-950q because we would call the reset
callback inside of dvb_attach() and the callback had not been setup yet.
Michael Krufky (who added the init_fw feature) says it's no longer required,
so just remove the option completely.
Thanks to user Zzeiss from #linuxtv chat for reporting the issue and
Michael Krufky <mkrufky@linuxtv.org> for proposing the fix.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
tda8290 were using some random video standard for FM. This results on random
errors. Instead, program tda8290 in expert mode, using a configuration near the
one specified on NXP datasheet for tda8295 (available on their site).
Also, properly display that the device is on radio mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Probably due to a removed code, tda827x were doing some wrong calculus at the
returned frequency. I suspect that the original idea were to return the
programmed divisor converted into frequency again.
However, the current code is sometimes multiplying the programmed frequency by
62500, and, on other cases, like radio, it dividing it by 1000.
Instead of doing such math, let's just store the frequency value as requested by
the caller module.
CC: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c: In function 'xc2028_sleep':
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c:1111: warning: 'return' with no value, in function returning non-void
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the firmware load is now fast on most boards, better to keep the tuner
off by default. A modprobe parameter were added to keep the old behavior,
to be used by old devices.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Julia Lawall <julia@diku.dk>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@i@
@@
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(E[...]))
+ ARRAY_SIZE(E)
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(T))
+ ARRAY_SIZE(E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Frederic CAND <frederic.cand@anevia.com>
Adds secam bgh support
Signed-off-by: Frederic CAND <frederic.cand@anevia.com>
|
|
From: Jose Alberto Reguero <jareguero@telefonica.net>
Jose reported:
I am using a Avermedia Volar X with af9015 driver(DVB-T).
The first time you use the card, first call reconfigure with MXL_QAM, and when
tune DVB-T it calls reconfigure with MXL_DVBT. But if you close the frontend
and open again, it calls reconfigure with MXL_QAM, but not call reconfigure with
MXL_DVBT because state->current_mode don't change(is MXL_DVBT).
Priority: normal
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
|
|
From: Darron Broad <darron@kewl.org>
This tuner was already supported by proxy as an FMD1216ME, however,
the MEX uses a different FM Radio IF so this addition is now required.
Priority: normal
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
|
|
From: Steven Toth <stoth@linuxtv.org>
mxl5005s: Checkpatch compliance
Priority: normal
Signed-off-by: Steven Toth <stoth@linuxtv.org>
|
|
From: Steven Toth <stoth@linuxtv.org>
xc5000: Checkpatch compliance
Priority: normal
Signed-off-by: Steven Toth <stoth@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware selection is very tricky on this device. This patch do a better
selection of the proper firmware type, by using a code to hint if the
firmware to be loaded should be D2620 or D2633.
It also allows overriding the hint at the control structure.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <devin.heitmueller@gmail.com>
The AMD ATI TV Wonder 600 has an XC3028L and *not* an XC3028, so we need to
load the proper firmware to prevent the device from overheating.
Priority: high
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Antti Palosaari <crope@iki.fi>
- implement I2C-gate control
Priority: normal
Signed-off-by: Antti Palosaari <crope@iki.fi>
|
|
From: Julia Lawall <julia@diku.dk>
The break after the return or goto serves no purpose.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Dont pass devptr in xc5000_attach, dont store it in xc5000_priv.
This pointer is passed into the tuner_callback function, which always
expects a pointer to fe->dvb->priv or i2c_adapter->algo_data.
This prevents future possible bugs in new drivers, such as using a "devptr"
other that the standard fe->dvb->priv in a DVB driver.
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Prevent an OOPS if xc5000_attach was called by tuner.ko before being called by
the DVB adapter driver. The OOPS occurs when a digital tune request is made
after tuner.ko is unloaded.
When tuner.ko is unloaded, it takes the xc5000_config structure with it.
Rather than storing a pointer to the xc5000_config structure, just store the
if_khz and tuner_callback inside the xc5000_priv internal state structure.
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Convert xc5000 to use the hybrid_tuner_request_state and
hybrid_tuner_release_state macros to manage state sharing between
hybrid tuner instances.
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
move struct xc5000_priv into xc5000.c and delete xc5000_priv.h
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Steven Toth <stoth@hauppauge.com>
I need this so I can better isolate my linux email from my
corporate email.
Priority: normal
Signed-off-by: Steven Toth <stoth@linuxtv.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Fixed a lot of sparse warnings: mostly warnings about shadowed variables
and signed/unsigned mismatches.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) and CDI Brasil
(www.cdibrasil.com.br/) for sponsoring this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
mxl5007 was forcing for its compilation:
In file included from drivers/media/common/tuners/mxl5007t.c:25:drivers/media/common/tuners/mxl5007t.h:80:1: warning: "CONFIG_MEDIA_TUNER_MXL5007T" redefined
In file included from <command-line>:0:
./include/linux/autoconf.h:2782:1: warning: this is the location of the previous definition
Probably, some temporary hack for testing.
CC: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Adrian Bunk <bunk@kernel.org>
After commit d9b19199e4894089456aaad295023263b5225c1a
(always enable FW_LOADER unless EMBEDDED=y) we can remove
the FW_LOADER select's and corresponding dependencies
on HOTPLUG.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
The use of mutex locking is overly paranoid in this driver.
The only locks we need are around the manipulation of the
register arrays. The other locks are not needed - remove them.
Thanks to Steven Toth for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
There is no reason to protect the i2c gate handling within the mxl5007t
state mutex.
Thanks to Steven Toth for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: roel kluin <roel.kluin@gmail.com>
lo1a and lo2a are unsigned ints so these tests won't work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The video_device_create_file and video_device_remove_file functions can be
removed from v4l2-dev.h, removing the dependency on videodev.h in v4l2-dev.h.
Also removed a few more videodev.h includes that should have been videodev2.h.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
