| Age | Commit message (Collapse) | Author |
|---|
|
From: Michael Krufky <mkrufky@linuxtv.org>
The patch moves the tda827x dvb tuning code to a separate module
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Antti Palosaari <crope@iki.fi>
This patch adds calls to i2c_gate_ctrl in the qt1010 dvb tuner module,
while removing the temporary hack in au6610 and gl861.
Tested successfully against fi-Oulu frequencies with
MSI Megasky 580 GL861 and Sigmatek DVB-110 AU6610.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
In older versions, this was used to decide whether to boot from
eeprom or file. This is no longer necessary but the check helps to avoid
an oops with misconfigured cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
There are the following changes:
- separate configuration of IF and GPIOs.
- set GPIOs before firmware load. This helps to avoid I2C address
collisions.
- if desired invert GPIOs at sleep (automatic return to analog mode of card).
- added 3 tuner configuration bytes to config stuct.
- added i2c gate address to config struct.
- moved _state struct declaration to header file to make it accessible
on board layer.
- added "conf_probed" to the state struct to allow i.e. probing for correct
tuner version.
- changed firmware load mechanism to always:
+ check if already loaded
+ try to boot from eeprom
+ try downlad from host
- corrected name of tda10046 firmware image (backward compatible).
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Mario Rossi <mariofutire@googlemail.com>
Second part of the patch to make the autosearch work again with DiB3000P/MC.
Signed-off-by: Mario Rossi <mariofutire@googlemail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Main changes:
- There were several checks for usb release routines that were removed, since
the routine itself checks for null values:
usb_free_urb, usb_kill_urb, usb_unlink_urb
Should be checked if this really happens on older kernels.
- updated sound/oss/btaudio.c
- replaced SLAB_ATOMIC to GFP_ATOMIC
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mario Rossi <mariofutire@googlemail.com>
After rewriting the driver the wrong autosearch index was used when
COFDM-parameter needed to be detected.
Thanks to Mario Rossi who found it.
Signed-off-by: Mario Rossi <mariofutire@googlemail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Rusty Scott <rustys@ieee.org>
Removes embedded log functions and makes use of the DVB math functions to
provide SNR in dB. The changes are modeled after recent changes made to
the LGDT330x frontends in lgdt330x.c
Signed-off-by: Rusty Scott <rustys@ieee.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Rusty Scott <rustys@ieee.org>
Removes embedded log functions and makes use of the DVB math functions
to provide SNR in dB. The changes are modeled after recent changes made
to the LGDT330x frontends in lgdt330x.c
Signed-off-by: Rusty Scott <rustys@ieee.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
In some cases when using VSB, the AGC status register has been known to
falsely report "no signal" when in fact there is a carrier lock. The
datasheet labels these status flags as QAM only, yet the lgdt330x
module is using these flags for both QAM and VSB.
This patch allows for the carrier recovery lock status register to be
tested, even if the agc signal status register falsely reports no signal.
Thanks to jcrews from #linuxtv in irc, for initially reporting this bug.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Andrew de Quincey <adq_dvb@lidskialf.net>
The tda10086 causes an oops (divide by zero) if a zero symbol rate is used;
this prevents this.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Added a dump I2C message to the TDA826x-driver to fix I2C read for
identification with ttusb2-driver.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
In lgh06xf_set_params:
Rename int variable "err" to "result".
Remove needless calculation of the set frequency, since this value is now
being returned by dvb_pll_configure().
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
This patch removes some duplicated code by returning the frequency set by
dvb_pll_configure(), instead of recalculating it again in dvb_pll_set_params()
and dvb_pll_calc_regs().
If the return value of dvb_pll_configure is less than zero, it is an error
code. Otherwise, the return value is the frequency actually set by the
function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
- adhere to 80-column limit
- replace some spaces with tabs
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
fix build error:
lgh06xf.h:29: error: syntax error before '{' token
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
We don't have to check for NULL before kfree()
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
This patch creates a new atsc tuner module for the LG TDVS-H06xF ATSC tuners,
called lgh06xf. The purpose of this change is to reduce some duplicated
code, and to allow the lgh06xf tuner code to take advantage of dvb_attach().
As a side effect, the dependency of dvb-bt8xx on dvb-pll has been removed,
since the lgh06xf module itself will use dvb-pll, while remaining optional
for the dvb-bt8xx driver through the use of DVB_FE_CUSTOMISE
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
This is a hybrid cardbus module. Besides the card support, i
modified the definition names for AGC and GPIO of the tda10046.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Alexey Dobriyan <adobriyan@gmail.com>
sparse "defined twice" warning
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Christoph Haubrich <christoph1.haubrich@arcor.de>
Copied routines for uc blocks and BER from the removed tda80xx.c
into tda8083.c.
Signed-off-by: Christoph Haubrich <christoph1.haubrich@arcor.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Update the SNR calculations to use the new dvb_math log function, and add
SNR calculations for all supported modulations for both lg dt3302 and dt3303.
The QAM equations don't appear in the dt3302 datasheet, so the ones from the
dt3303 datasheet were used.
SNR returned is the actual value in dB as 8.8 fixed point.
Reporting of real signal strength isn't supported, so rather than return 0,
which confuses some software and users, a re-scaled SNR value is returned.
Code originally by Rusty Scott.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Rusty Scott <rustys@ieee.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
This patch contains several fixes for the autosearch algorithm and other small ones.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pboettcher@dibcom.fr>
This patch contains support for the DiB7000PC-driver.
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
|
|
From: Patrick Boettcher <pboettcher@dibcom.fr>
First working version of the dib7000m-driver. This commit also makes the Hauppauge NOVA-T Stick working.
Signed-off-by: Francois Kanounnikoff <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Let the MT2060 be customized like most of the other DVB PLLs/front-ends.
Also, add a missing dependency on I2C.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
When a front-end is disabled, card drivers that use it are compiled with
a stub version of the front-end's attach function. This way they have no
references to the front-end's code and don't need it to be loaded.
If a card driver is compiled into the kernel, and a front-end is a
module, then that front-end is effectively disabled wrt the card driver.
In this case, the card driver should get the stub version. This was not
happening.
The stub vs real attach function selection is changed so that when the
front-end is a module the real attach function is only used if the card
driver is a module as well. This means a module front-end will be
supported by card drivers that are modules and not supported by card
drivers compiled into the kernel.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Added config-struct-parameter to take board-specific AGC command 1 and 2 into account.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Antti Palosaari <crope@iki.fi>
QT1010:
- old qt1010-code totally rewritten and put in own kernel module
- same enhancements as my earlier QT1010 125kHz patch
- tuner initialization
- register 1f calculation
- register 20 calculation
- register 25 calculation
m920x: (MSI Megasky)
- use new QT1010 module instead of old code
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Jan Nijs <jan.nijs@scarlet.be>
This patch changes qt1010.h to use dvb_usb_device struct instead of a
dvb_usb_adapter for accessing the private area of the driver.
Without this patch my PC hard locks when an application tries to access
the DVB tuner.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Steven Toth <stoth@hauppauge.com>
A number of people have been reporting wierd tuning problems with various
cards. Yeasah tracked down the problem to a miss-read datasheet. This
resolves the problems.
Signed-off-by: Yeasah Pell <yeasah@schwide.net>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
The megasky_tuner_attach function is not specific to this device.
This patch renames it to qt1010_tuner_attach and moves it into the qt1010
header file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Aapo Tahkola <aet@rasterburn.org>
- hardware pid filtering no longer enabled unless in usb 1.x mode
- more responsive rc handling
- some minor bug fixes and code refolding
- m9206_write delay dropped (doesn't seem to be needed)
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
qt1010 is a tuner used in some other devices, so this code should be put
into a separate file so that it could be reused by other drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Removed compilation warnings for unused statics and locals
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
- forward the clock to the slave undivided
- when sleeping the 3000 do not shutdown the clock
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
- make the timing frequency update work.
- fix AGC calibration for Nova-T 500
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
This changeset finalizes the support of the Hauppauge Nova-T 500 (Dual DVB-T).
It adds correct AGC setting for the 3000P, correct firmware download state
detection.
Additionally it fixes the mt2060-driver to be able to be used with dvb_attach.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Changed the attach-function of the dib3000mc-driver to return only one
frontend. In case of multiple dib3000-chips on one board, one has to call the
i2c-enumeration manually before.
Added a field to Microtune 2060 config to output the clock to other
tuners/device on a board.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Andrew de Quincey <adq_dvb@lidskialf.net>
I had forgotten to add the wrapper round the tua6100_attach function if its
disabled in Kconfig
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
|
|
From: Andrew de Quincey <adq_dvb@lidskialf.net>
This driver was originally in budget-av.c, however I have extracted it into
a seperate file to permit reuse.
I also reworked the code to make it maintainable. I then examined the KNC1
windows drivers and rewrote the code in order to configure the PLL as they
do. This solves a lot of reported tuning problems.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
|
|
From: "Bradley Kite" <bradley.kite@gmail.com>
The cx22702 returns an 8 bit unshifted value for signal strength; this is
inconsistent with most other frontends
Signed-off-by: Bradley Derek Kite <bradley.kite@gmail.com>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
The release callback was installed in ops.release, it should have been
ops.release_sec. This prevented to front-end release from getting
called.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
