| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2004-02-24 | Added a temporary hack to fix buggy user-side software which supplies | Andrew de Quincy | |
| INVERSION_AUTO to frontends which specifically say they do not support it | |||
| 2004-02-24 | Further refinements: force a full tune whenever FE_INIT is done. | Andrew de Quincy | |
| Remove unnecessary inititalised stuff | |||
| 2004-02-23 | Fixes to sort out tuning at low symbol rates | Andrew de Quincy | |
| 2004-02-21 | Updated documentation to contain note about USB devices | Andrew de Quincy | |
| 2004-02-20 | Added seperate settings for SU1278 on technotrend hardware | Andrew de Quincy | |
| 2004-02-16 | DVB_TDA1004X and DVB_NXT6000 do not depend on !STANDALONE | Johannes Stezenbach | |
| (i.e. no compile-time firmware image necessary) reported by Bernd Bartmann | |||
| 2004-02-15 | - change AFC handling as suggested by Robert Schlabbach | Johannes Stezenbach | |
| - use bit 1 of the SYNC register for FE_HAS_SIGNAL | |||
| 2004-02-15 | verbose-print AFC only if carrier has been recovered | Johannes Stezenbach | |
| 2004-02-13 | turn off ves1820 test output pins (don't know if this makes | Johannes Stezenbach | |
| any difference, but why have them turned on if nothing is connected to them?) | |||
| 2004-02-09 | fixed typo | Holger Waechtler | |
| 2004-02-07 | gcc-3.5 compatibilty patch from 2.6.3-rc1 | Johannes Stezenbach | |
| 2004-02-06 | add nxt6000 frontend driver to Makefiles | Johannes Stezenbach | |
| 2004-02-03 | patch by Geert Uytterhoeven: Never include <asm/delay.h> directly. | Johannes Stezenbach | |
| 2004-01-30 | Standardised where the firmware should be. | Andrew de Quincy | |
| 2004-01-29 | Changed to use full i2c reads in probing instead of i2c pings to be | Andrew de Quincy | |
| compatable with ttusb | |||
| 2004-01-29 | bugfix by Robert Cook: FE_RESET did the same as FE_INIT, thus invalidating | Andreas Oberritter | |
| current channel settings on FE_RESET | |||
| 2004-01-28 | Need to re-invert inversion for tda10046 in get_fe() | Andrew de Quincy | |
| 2004-01-28 | Now resets chip before uploading firmware | Andrew de Quincy | |
| 2004-01-28 | Had to split firmware upload off from frontend init... the initial tune attempt | Andrew de Quincy | |
| was taking too long. Also, provided explanation of tuner frequency calculations. | |||
| 2004-01-27 | Fixed frequency calculation.. realised its exactly the same as the | Andrew de Quincy | |
| tda10045h one! | |||
| 2004-01-27 | Fixed signal strength reading for tda10046h | Andrew de Quincy | |
| 2004-01-27 | Updated description | Andrew de Quincy | |
| 2004-01-27 | Small tweaks. Better inversion handling, and changed how 6MHz is set in | Andrew de Quincy | |
| tuner | |||
| 2004-01-27 | Forgot to make sure inversion was on for TDA10046H | Andrew de Quincy | |
| 2004-01-27 | Implemented tda10046h driver | Andrew de Quincy | |
| 2004-01-26 | don't send zero-byte messages when probing the PLL type | Holger Waechtler | |
| 2004-01-23 | - spelling fix: aquire -> acquire | Michael Hunold | |
| 2004-01-16 | merge frontend improvements from DVB tree: | Johannes Stezenbach | |
| - schedule_timeout(1) in dvb_frontend.c after setting frontend and before waking up frontend thread - do FE_RESET in each iteration of frontend thread if !FE_HAS_LOCK - use aquire_signal flag to call FE_RESET only after tuning until FE_HAS_LOCK has been signalled, and not when FE_HAS_LOCK drops out for short periods of time later | |||
| 2004-01-06 | - fix compilation with "make allyesconfig": make av7110 | Michael Hunold | |
| compile-firmware-in-driver option depend on STANDALONE - change some default file locations from /etc/dvb/ to /usr/lib/hotplug/firmware/ | |||
| 2003-12-24 | - give more credit to Jamie Honan, he's the guy that has done most of the | Michael Hunold | |
| hard work for TwinHan / DST support. | |||
| 2003-12-23 | remove AUTO_INVERSION for capabilities (not true) | Jamie Honan | |
| allow params dst_type_flags and dst_type to have multiple values for multiple cards in one machine | |||
| 2003-12-20 | increase mdelay from 30 to 50 to be more reliable with bad reception quality | Andreas Oberritter | |
| 2003-12-20 | updated contributors.txt and some email addresses | Andreas Oberritter | |
| 2003-12-09 | use correct delay values, don't divide by HZ when using dvb_delay(). | Holger Waechtler | |
| found by Artur Skawina. | |||
| 2003-12-01 | patch for the mt312 module, targeting the VP310. Contributed by Augusto Cardoso. | Holger Waechtler | |
| 1) Reduced heat in most applications of the VP310. This is specially important on the Skystar2 application. Some old boards based on the VP310 will have heat problems without this patch an may be permanently damaged. 2) Implement "auto" inversion mode for the VP310. With this and a VP310, you don't have to worry about inversion, this is like it should be. 3) Remove unnecessary "prints". 4) Add the ability to generate a module with the option to use debug. When MT312_DEBUG is 0, there is no debug code in the module. When it's set to 1, it's possible to control debug using the module parameter "debug=1" | |||
| 2003-11-29 | set FE_HAS_LOCK only when all low-order bits are valid | Holger Waechtler | |
| 2003-11-27 | - completed nokia board support | Andreas Oberritter | |
| - increased delay before inversion change to 30ms to get constant results - added 30ms delay after FE_SET_FRONTEND for quick and stable tuning. don't know why it is that much faster with it, I noticed it by pure luck after adding a printk which delayed for about 4 jiffies. ;) maybe it avoids a bug or delay in some other part of the code (maybe dvb_frontend.c?). feedback by pci card users would be appreciated. - changed a c++ comment to c style | |||
| 2003-11-27 | fix typo in code rate table lookup for FE_GET_FRONTEND | Holger Waechtler | |
| - p->code_rate_LP = fec_tab[val >> 3]; + p->code_rate_LP = fec_tab[val & 0x07]; | |||
| 2003-11-27 | - set default pwm value to 0x48 for boards which don't have an eeprom at i2c ↵ | Andreas Oberritter | |
| address 0x50 instead of using a random value of an uninitialized local variable. - don't bail out if no tuner could be detected, for compatibility with boards which don't have a tuner on the same bus as the demod. | |||
| 2003-11-25 | make it compile with non-C99-compliant gcc versions. Patch contributed by ↵ | Holger Waechtler | |
| Wolfgang Thiel | |||
| 2003-11-23 | fix frontend private data handling. patch by Mikael Rosbacke <rosbacke at ↵ | Andreas Oberritter | |
| nada.kth.se> | |||
| 2003-11-20 | obsolete, removed. | Holger Waechtler | |
| 2003-11-20 | firmware loader implementation contributed by Martin Stubbs | Holger Waechtler | |
| 2003-11-19 | Whoops, forgot to add a "return 0" at the end of the init function | Andrew de Quincy | |
| 2003-11-19 | Added new module parameter to choose between BER and UCBLOCKs error | Andrew de Quincy | |
| monitoring since the STV0299 can't do both at once (BER is the default) | |||
| 2003-11-12 | - use per i2c-adapater void pointer for private data in nxt_attach() / ↵ | Michael Hunold | |
| nxt_detach() feedback appreciated! | |||
| 2003-11-12 | - compile fix | Michael Hunold | |
| 2003-11-12 | - re-indent the source | Michael Hunold | |
| - remove unnecessary blank lines - remove #pragma stuff - add 3 obviously missing break statements in nxt6000_dump_status() - use c style comments instead of // - remove bogus version history from header file - remove Windoze style <cr> from header file | |||
| 2003-11-12 | Added modifications based on the recommended settings in the SU1278 | Andrew de Quincy | |
| datasheet. Cleaned up some tabbing problems. | |||
| 2003-11-12 | - let the samsung tuner module count bit errors instead of block errors | Holger Waechtler | |
| - some indentination stuff | |||
 |
index : mediapointer-dvb-s2 | |
| Mediapointer DVB-S2 driver | www-data |
| summaryrefslogtreecommitdiff |