| Age | Commit message (Collapse) | Author |
|---|
|
From: David Härdeman <david@hardeman.nu>
The IR chip has no address decoding, so the IR data is always present in
the high byte when doing a read from the saa7146 chip. This means that
the DEBI address used is irrelevant to the IR decoding logic.
DEBI addresses 0x1XXX are mapped to the registers on the CI module
itself, but only the lowest two bits are actually used (see EN50221,
section A.2.2.1), meaning that 0x1234 is equivalent to 0x1000 which maps
to register 0 (the data register). A read from the data register is
supposed to be preceded by a read from the size register, so some CI
modules will be confused (the AlphaCrypt CAM will hang completely).
The attached patch changes the address used when reading the IR data to
use 0x4000 instead. This is the CI version address, which is a safer
default, works with the AlphaCrypt CAM and matches the behaviour of the
Windows driver (AFAIK).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
Kernel-sync:
This patch is required to allow compilation of the tree with kernel
2.6.19.
This is the original description of the original patch, signed by
David Howells <dhowells@redhat.com>:
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Forgot to increase the device count for the STK7700P-devices
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
correct AVerMedia Volar USB ID
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Henning Schroeer <post@henning-schroeder.de>
Adding USB IDs for Uniwill STK7700P-ref-design
Signed-off-by: Henning Schroeer <post@henning-schroeder.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Tomi Koivulahti <birchbay@gmail.com>
This patch adds Compro Videomate U500 to supported devices.
Signed-off-by: Tomi Koivulahti <birchbay@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
This patch contains several fixes for the autosearch algorithm and other small ones.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pboettcher@dibcom.fr>
This patch contains support for the DiB7000PC-driver.
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
|
|
From: Patrick Boettcher <pboettcher@dibcom.fr>
First working version of the dib7000m-driver. This commit also makes the Hauppauge NOVA-T Stick working.
Signed-off-by: Francois Kanounnikoff <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
|
|
From: Luke Deller <luke@deller.id.au>
Add support for more keys on the remote control included with the
DigitalNow tinyUSB2 DVB-T Receiver.
Signed-off-by: Luke Deller <luke@deller.id.au>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Let the MT2060 be customized like most of the other DVB PLLs/front-ends.
Also, add a missing dependency on I2C.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
When a front-end is disabled, card drivers that use it are compiled with
a stub version of the front-end's attach function. This way they have no
references to the front-end's code and don't need it to be loaded.
If a card driver is compiled into the kernel, and a front-end is a
module, then that front-end is effectively disabled wrt the card driver.
In this case, the card driver should get the stub version. This was not
happening.
The stub vs real attach function selection is changed so that when the
front-end is a module the real attach function is only used if the card
driver is a module as well. This means a module front-end will be
supported by card drivers that are modules and not supported by card
drivers compiled into the kernel.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Added config-struct-parameter to take board-specific AGC command 1 and 2 into account.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
While converting everything to DVB-USB-Adapter, there was a wrong indention.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
When using the remote control with the Nova-T USB there was an Oops because of
the recent DVB-USB-Adapter change.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Amit Choudhary <amit2030@gmail.com>
Check the return value of kmalloc() in function frontend_init(),
in file drivers/media/dvb/bt8xx/dvb-bt8xx.c.
Signed-off-by: Amit Choudhary <amit2030@gmail.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Apply the relevant parts of a patch from Pete Zaitcev <zaitcev@redhat.com>
kernel-sync:
Original description:
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
kernel-sync:
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Applied the rellevant v4l-dvb part of this patch from
David Brownell <dbrownell@users.sourceforge.net>
kernel-sync:
Original description:
Small driver suspend() fixes in preparation for the PRETHAW events:
- Only compare message events for equality against PM_EVENT_* codes;
not against integers, or using greater/less-than comparisons.
(PM_EVENT_* should really become a __bitwise thing.)
- Explicitly test for SUSPEND events (rather than not-something-else)
before suspending devices.
- Removes more of the confusion between a pm_message_t (wraps event code)
and a "state" ... suspend() originally took a target system state.
These updates are correct and appropriate even without new PM_EVENT codes.
benh: "I think in the Mesh case, we should handle the freeze case as well or
we might get wild DMA."
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch includes at the v4l-dvb tree several documentation
fixes applied at kernel tree.
kernel-sync:
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/dvb-usb/usb-urb.c: In function 'usb_allocate_stream_buffers':
drivers/media/dvb/dvb-usb/usb-urb.c:125: warning: format '%u' expects type 'unsigned int', but argument 4 has type 'long long unsigned int'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Steven Toth <stoth@hauppauge.com>
A number of people have been reporting wierd tuning problems with various
cards. Yeasah tracked down the problem to a miss-read datasheet. This
resolves the problems.
Signed-off-by: Yeasah Pell <yeasah@schwide.net>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Randy Dunlap <rdunlap@xenotime.net>
Use NULL instead of 0 for pointer value, eliminate sparse warnings.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
add support for DViCO FusionHDTV DVB-T Dual Digital 2 USB, which
is identical to the usb portion of DViCO FusionHDTV DVB-T Dual Digital 1.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Steven Toth <stoth@hauppauge.com>
This patch enables generic bus arbitration callbacks enabling
dvbcore frontend_open and frontend_release to pass 'acquire'
and 'release' hardware messages back into the DVB bridge frameworks.
Frameworks like cx88 can then implement single bus multiple demod
card sharing features, which would prohibit two frontends from attempting
to use a single transport bus at the same time.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Fixed mt2060-usage with dvb_attach
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Corrected power control of the device for dual boards
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
When converting the dib3000mc-driver to dvb_attach I forgot to invert the check for NULL.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Removed compilation warnings for unused statics and locals
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Added a module parameter for force the activation of any LNA on a board.
Suggest by Steve Toth.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
- forward the clock to the slave undivided
- when sleeping the 3000 do not shutdown the clock
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
- make the timing frequency update work.
- fix AGC calibration for Nova-T 500
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Adding another USB product ID for the Nova-T 500. Reported by Jose Alberto Reguero.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Several fixes for dib0700-module. (Firmware error checking, dependency)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
The fixed support for the VP70x (supports only StarBox2) is now in sync with
latest changes in the dvb-usb framework.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
This changeset finalizes the support of the Hauppauge Nova-T 500 (Dual DVB-T).
It adds correct AGC setting for the 3000P, correct firmware download state
detection.
Additionally it fixes the mt2060-driver to be able to be used with dvb_attach.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Added module for DiB0700 based USB devices. This module is preliminary and
untested (because of a lack of test devices) but should work.
Further commits will be necessary to make it work properly.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Changed the attach-function of the dib3000mc-driver to return only one
frontend. In case of multiple dib3000-chips on one board, one has to call the
i2c-enumeration manually before.
Added a field to Microtune 2060 config to output the clock to other
tuners/device on a board.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Forgot to add usb-urb.c which is new after adding support for multiple inputs
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Patrick Boettcher <pb@linuxtv.org>
Small fix for multi input for dtt200u module.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
Multi-input patch for DVB-USB device
From: Patrick Boettcher <pb@linuxtv.org>
This patch is the first commit of the Multiple Input Patch for the DVB-USB frame
work.
It changes the DVB-USB-device to be able to have more than one streaming input
(e.g. multiple DVB-T sources) on one device. This is a necessary feature for
the upcoming DiB7700 driven devices.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Oliver Endriss <o.endriss@gmx.de>
Implement fix suggested by Michael Hunold for a bug reported
by Philipp Matthias Hahn: Starting "kdetv" on a Siemens DVB-C 1.x
produced an oops because kdetv opened "/dev/vbi0".
Remove the V4L2_CAP_VBI_CAPTURE flag because it does not work with
this type of hardware anyway.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
From: Oliver Endriss <o.endriss@gmx.de>
Do not select FW_LOADER unless it is really required.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
