| Age | Commit message (Collapse) | Author |
|---|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Remove unused variable from when I introduced the g_std() function.
This work was sponsored by EyeMagnet Limited.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Remove redundant call to set the vinctrl register. This eliminates any
ambiguity as to how the register is configured (since it is now always set in
em28xx_set_outfmt).
This work was sponsored by EyeMagnet Limited.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
We need to implement the g_std call, or else the default norm always gets
returned, which breaks VBI capturing if you had changed the standard to NTSC
using s_std.
I had temporarily changed the default norm to NTSC so that zvbi-ntsc-cc
wouldn't choke, so now that we are returning the correct value, switch it back
to PAL as the default.
This work was sponsored by EyeMagnet Limited.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Change the code so we only claim to support VBI if the underlying chipset
actually has the support.
This work was sponsored by EyeMagnet Limited.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Do not create the VBI device in cases where VBI is not supported on the target
em28xx chip.
This work was sponsored by EyeMagnet Limited.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Remove an unreferenced variable introduced during the VBI introduction.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
The current locking infrastructure didn't support having multiple fds accessing
the device (such as video and vbi). Rework the locking infrastructure,
borrowing the design from cx88.
This work was sponsored by EyeMagnet Limited.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
When adding support for both video and VBI, I missed the mmap ioctl. Add
the missing call.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Add support for raw VBI capture for the em28xx bridge, currently only for
NTSC. Support for PAL capture to follow shortly (including the removal of
numerous hard-coded NTSC-specific sizes for capture buffers, etc).
Note that the code currently changes the default current norm from PAL to
NTSC (so that zvbi-ntsc-cc works properly). The default norm really should
be moved into a board-level parameter.
This work was sponsored by EyeMagnet Limited.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Add code enabling the VBI registers for variants of the em28xx chip that
support VBI, and make sure the isoc streaming code continues to work for
the video component of the stream (note the video and vbi data arrive
intermixed on the same isoc pipe).
Note that this version just drops the actual VBI data onto the floor as
opposed to processing it. The "#ifdef 0" tags are for the videobuf code that
appears in the next patch in this series.
We created a separate version of the isoc_copy version for parsing the version
of the stream that includes VBI data. In theory, they might be able to be
merged at some point in the future, but the initial goal is to ensure that we
do not cause any regressions with devices that do not have VBI support.
This work was sponsored by EyeMagnet Limited.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Properly document the video input control register, in preparation for the
addition of VBI support. Note this patch makes no functional changes.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Shine Liu <shinel@foxmail.com>
[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Shine Liu <shinel@foxmail.com>
We should call em28xx_ir_init(dev) only when disable_ir is true.
Signed-off-by: Shine Liu <shinel@foxmail.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Steve Gotthardt <gotthardt@gmail.com>
[mchehab@redhat.com: fix merge conflict and a few CodingStyle issues]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Restore support for digital tuning caused by regression during introduction
of disable_i2c_gate parameter to zl10353 driver.
Thanks to user "Xwang" for reporting the problem and testing the fix
Priority: high
Cc: Xwang <xwang1976@email.it>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Douglas Schilling Landgraf <dougsland@redhat.com>
Fixed eeprom hash table
Priority: normal
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Register 0x13 seems to be a sort of image control, maybe gamma. Lower
values produce better images, while higher values increases the contrast
and shifts colors to green. 0xff produces a black image.
If this register is left alone, a random value can be found at the
register, producing weird results.
This register doesn't seem to affect tv streams.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Silvercrest mt9v011 sensor produces a 640x480 image. However,
previously, the code were getting only half of the lines and merging two
consecutive frames to "produce" a 640x480 image.
With the addition of progressive mode, now em28xx is working with a full
image. However, when the number of lines is bigger than 240, the
beginning of some odd lines are filled with blank.
After lots of testing, and physically checking the device for a Xtal, it
was noticed experimentally that mt9v011 is using em28xx XCLK as its
clock. Due to that, changing XCLK value changes the maximum speed of the
stream.
At the tests, it were possible to produce up to 32 fps, using a 30 MHz
XCLK. However, at that rate, the artifacts happen even at 320x240. Lower
values of XCLK produces artifacts only at 640x480.
At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is
possible to see an invalid sucession of artifacts with this pattern:
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
(where the dots represent the blanked pixels)
So, it seems that a waveform in the format of a ramp is interferring at
the image.
The cause of this interference is currently unknown. Some possibilities
are:
- electrical interference (maybe this device is broken?);
- some issue at mt9v011 programming;
- some bug at em28xx chip.
So, for now, let's be conservative and use a value of XCLK that we know
for sure that it won't cause artifacts.
As I'm waiting for more of such devices with different em28xx chipset
revisions, I'll have the opportunity to double check the issue with
other pieces of hardware.
Later patches can vary XCLK depending on the vertical resolutions, if a
proper fix is not discovered.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.
Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't know the xtal frequency of Silvercrest, but we need to have
some value in order to allow controlling the frame rate frequency. The
value is probably still wrong, since the manufacturer announces this
device as being capable of 30fps, but the maximum we can get is
13.5 fps.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:
1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;
2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by hermann pitton <hermann-pitton@arcor.de>, some devices
has a different chip id for em2710 (likely the older ones):
em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0)
em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22)
em28xx #0: em28xx chip ID = 17
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new
variation.
Priority: normal
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx doesn't have temporal scaling. However, on webcams, sensors are
capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should
be passed to the sensor for it to properly set frame rate.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
without it
From: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API (chapter 1.5) states that:
Drivers must implement all input ioctls when the device has one
or more inputs, all output ioctls when the device has one or more outputs.
When the device has any audio inputs or outputs the driver must set the
V4L2_CAP_AUDIO flag in the struct v4l2_capability returned by the
VIDIOC_QUERYCAP ioctl.
So, devices without audio input should return -EINVAL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@linuxtv.org>
Add support for the remote control that comes with the Cinergy Hybrid T USB XS
Thanks to Jelle de Jong for providing sample hardware to test with.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Cc: Jelle de Jong <jelledejong@powercraft.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Even devices without ac97 needs to call analog audio setup function, to
properly set xclk and mute/unmute.
Thanks to Angelo Cano <acano@fastmail.fm> for reporting and testing it.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.
Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.
Priority: normal
Tested-by: Angelo Cano <acano@fastmail.fm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean Delvare <khali@linux-fr.org>
There is no point in defining I2C adapter IDs when no code is using
them. As this field might go away in the future, stop using it when
we don't need to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.
This simplifies this API substantially.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From
the revision history at the mt9v011 datasheet, it seems that the chip
version has changed from the first release of the chip.
Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to
me, on his tests with a Silvercrest webcam.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, some devices with saa711x had their parameters controlled
directly inside em28xx driver, instead of using their proper module for
it.
Due to that, the ac97 controls were mixed with saa711x ones.
Older patches removed all saa711x controls, but we still need to control
ac97 devices on em28xx, since we don't have a separate v4l2 device for
it.
The proper way to address is to create a separate ac97 v4l2 device.
While we don't have it, we should clean up the code to allow having a
better view of what is part of em28xx core code and what's due to ac97
control inside it.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
As em28xx chip has nothing to do with volume/mute controls, rename those
controls to properly indicate that they control the companion AC97 chip
that it is inside the boards with this chip.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which
is required for digital tuning to work properly. Add the missing profile.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Priority: normal
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
In cases where the device has a generic Empia USB ID, the call in the
precard setup phase did not set the tuner GPIO. As a result, the tuner may
not be taken out of reset before attempting initialization in the analog
driver.
This problem was not seen before with the EVGA inDtube, since that particular
board has the analog GPIO setup to include taking the tuner out of reset.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment for the Pinnacle 320e.
Priority: normal
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Wally <wally@voosen.eu> for bringing the issue and helping
with the tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the video input format, vinmode/vinctl needs adjustments.
For TV, this is not relevant, since the supported decoders output data
at the same format. However, webcam sensors may have different formats,
so, this needs to be adjusted based on the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to properly estimate fps, mt9v011 sensor driver needs to know
what is the used frequency on the sensor cristal. Adds the proper fields
and initialization code for specifying the cristal frequency.
Also, based on experimentation, it was noticed that the Silvercrest is
outputing data at 7 fps. This means that it should be using a 6.3 MHz
cristal. This information needs to be double checked later, by opening
the device. Anyway, by using this value for xtal, at least now we have
the correct fps report.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
