| Age | Commit message (Collapse) | Author |
|---|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
When trying to DMA userspace buffers to the cx23415 you need to check
whether the page is in highmem. If this is the case, then bounce buffers
have to be used to allow DMA.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
- add FILE debug flag for open/close/read/write/poll.
- show cmd for encoder/decoder command ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Some streams (PCM, VBI decoding) do not need that much memory, so specify
the allocated memory in kB instead of MB to limit memory usage. E.g. 1 MB
is overkill for the VBI decoding stream, 64 kB is enough.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
It turns out that the cx23415/6 DMA engine cannot do scatter/gather DMA
reliably. Every so often depending on the phase of the moon and your
hardware configuration the cx2341x DMA engine simply chokes on it and
you have to reboot to get it working again.
This change replaced the scatter/gather DMA by single transfers at a time,
where the driver is now responsible for DMA-ing each buffer.
UDMA is still done using scatter/gather DMA, that will be fixed soon.
Many thanks to Mark Bryars <mark.bryars@etvinteractive.com> for discovering
the link between scatter/gather and the DMA timeouts.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
When there are no more free buffers, then buffers are stolen from the
predma queue. Buffers should be stolen from the head of that queue (which
is where the most recently added buffers are) and all buffers belonging
to a frame should be stolen. Otherwise 'half-frames' would remain in the
queue, which leads to ugly playback and complete sync failure for YUV
buffers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
By request of mchehab I've removed the userspace tuner dependent code.
Use my v4l-dvb-xc tree in the meantime for the userspace tuner support.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
- Split Club3D card from Yuan PG600-2, GotView PCI DVD Lite (different composite input)
- Add AVerTV MCE 116 Plus (M116) card
- Allow Xceive cards to be used without Xceive support
- Update Xceive support to latest userspace tuner (still not on by default,
pending inclusion of userspace tuner in the kernel).
- Use CONFIG_XC3028 rather than HAVE_XC3028: gentree.pl will remove them
automatically.
Thanks to Markus Rechberger for help with the userspace tuner support.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Ian Armstrong <ian@iarmst.demon.co.uk>
In the current driver, the field order is global. As soon as it's changed it
takes immediate effect. This is a problem when the video changes order mid
stream. Although it mostly works okay, the video may judder / flicker.
This patch attaches the field order to the frame, so that any buffered frames
will not be displayed until the correct field. In the event that the field
order is changed mid stream, the driver will ensure that the previous frame
is displayed for a minimum of 3 fields. These are the two original fields the
frame should have occupied, plus the one extra since the new frame still has
to wait for the correct field.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The firmware is now loaded when the driver is actually used for the first
time. This allows the driver to be compiled in-kernel instead of as a module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Pausing a decoder followed by a Play command would do nothing. Fixed.
Pausing a decoder running at non-standard speed following by a Continue
would reset the speed to 100%. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Add the ivtv-fb framebuffer driver for cx23415 devices (currently
only the Hauppauge PVR-350 cards). This makes it possible to use
the On-Screen Display functionality of these cards, either for menus
during MPEG playback, or as a console or X display.
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: John P Harvey <john.p.harvey@btinternet.com>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Add support for high volume debug messages, allowing them to be turned
on selectively.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Starting an MPEG and VBI capture simultaneously caused errors in
the VBI setup: this setup was done twice when it should be done
only for the first stream that is opened.
Added a mutex to prevent this from happening.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The old service_set_out setting was still tested, even though it no longer
was ever set and was in fact obsolete. This meant that everything that was
written to /dev/vbi16 was ignored. Removed the service_set_out variable
altogether and now it works again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Sliced VBI transfers use PIO instead of DMA. This was done inside the
interrupt handler, but since PIO accesses are very slow this meant that
a lot of time was spent inside the interrupt handler. All PIO copies are
now moved to a workqueue. This should fix various issues with missing time
ticks and remote key hits.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
As pointed by Geert Uytterhoeven <geert@linux-m68k.org>, ivtv-driver.h
have two checks for CONFIG vars, inerited from the time it were an out
of kernel driver. Also, ivtv were wrongly marked as dependent of USB.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Ian Armstrong <ian@iarmst.demon.co.uk>
Modifies automatic mode selection for yuv playback. Behaviour is now that
source video with a vertical resolution below that of the currently set
broadcast mode will be treated as progressive. Video with a vertical
resolution greater or equal to the current broadcast mode (up to 576 lines)
will be treated as interlaced.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
build failure in 2.6.15:
CC [M] ivtv-driver.o
ivtv-driver.c: In function 'ivtv_init_struct1':
ivtv-driver.c:625: warning: implicit declaration of function 'mutex_init'
ivtv-driver.c: In function 'ivtv_probe':
ivtv-driver.c:1170: error: 'IRQF_SHARED' undeclared (first use in this function)
ivtv-driver.c:1170: error: (Each undeclared identifier is reported only once
ivtv-driver.c:1170: error: for each function it appears in.)
ivtv-driver.c:1170: error: 'IRQF_DISABLED' undeclared (first use in this function)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
This is needed for ivtv-fb.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Convert the '//' comments to kernel approved /* */ style comments.
Set the default debug level to 0. As a result of which change some
DEBUG_WARNs to errors or remove them altogether.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
It took three core maintainers, over four years of work, eight new i2c
modules, eleven new V4L2 ioctls, three new DVB video ioctls, a Sliced
VBI API, a new MPEG encoder API, an enhanced DVB video MPEG decoding
API, major YUV/OSD contributions from Ian and John, web/wiki/svn/trac
support from Axel Thimm, (hardware) support from Hauppauge, support and
assistance from the v4l-dvb people and the many, many users of ivtv to
finally make it possible to merge this driver into the kernel.
Thank you all!
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: John P Harvey <john.p.harvey@btinternet.com>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
|
