summaryrefslogtreecommitdiff
path: root/linux/drivers/media/video/ivtv
AgeCommit message (Collapse)Author
2007-10-14ivtvfb: YUV output size fix when ivtvfb is not loaded.Hans Verkuil
From: Ian Armstrong <ian@iarmst.demon.co.uk> If the ivtvfb module isn't loaded, the valid YUV output area should be set to full-screen. This patch fixes the case where the valid output area was not reset when the output broadcast format was changed from NTSC to PAL. This resulted in output being limited to the top 480 lines of the display. Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-14ivtvfb: YUV handling of an image which is not visible in the display area.Hans Verkuil
From: Ian Armstrong <ian@iarmst.demon.co.uk> When the ivtvfb module is loaded, the YUV output is relative to the framebuffer output. When a virtual screen size is used, the output area for the YUV may actually be off screen. To prevent the hardware from crashing, the current driver will ignore an off-screen position and leave the output visible at the last on-screen position. This may not be desirable, so this patch will switch off the YUV output should the image move off-screen, and re-enable it should the image move on-screen again. Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-14ivtvfb: check return value of unregister_framebuffer.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Prevent unloading the framebuffer if it is still in use. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-13ivtv: fix circular locking (bug 9037)Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> If you try to access the video device from within an udev rule, then you get into a circular locking situation. Changed the driver to postpone the registration of the devices until everything else has been fully initialized, so that the newly created device can be used immediately. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-12ivtv: fix resizing MPEG1 streamsHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Resizing an MPEG 1 stream would cut off the right half of the image due to a missing divide by 2 in VIDIOC_S_FMT. Also did some minor cleanup in this part of the code. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-12ivtvfb: screen mode change sometimes goes wrong.Hans Verkuil
From: Ian Armstrong <ian@iarmst.demon.co.uk> This patch partially reverts a previous change that caused the CX2341X_OSD_SET_PIXEL_FORMAT firmware calls to be skipped when the pixel format of the framebuffer wasn't altered by FBIOPUT_VSCREENINFO. Unfortunately, another firmware call on the PVR350 sometimes scrambles the display when trying to adjust the framebuffer settings. This patch re-enables the CX2341X_OSD_SET_PIXEL_FORMAT calls to try and prevent this from occurring. Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-12ivtv: set the video color to black instead of green when capturing from the ↵Hans Verkuil
radio. From: Hans Verkuil <hverkuil@xs4all.nl> Thanks-to: Martin Dauskardt <md001@gmx.de> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-12ivtv: fix incorrect EBUSY return.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Trying to open the radio when a capture is in progress will make it impossible to open the radio again since the radio stream wasn't released. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-14 ivtv: fix NULL dereferenceMauro Carvalho Chehab
From: Adrian Bunk <bunk@kernel.org> We shouldn't dereference "itv" when we know it's NULL... Spotted by the Coverity checker. Signed-off-by: Adrian Bunk <bunk@kernel.org> Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-10-10ivtv: Replace list_for_each+list_entry with list_for_each_entryTrent Piepho
From: Trent Piepho <xyzzy@speakeasy.org> Also fixed a few cases of cut&paste errors where 'buf' would be set to the first entry in the list prior to be used as the loop iterator. In one case the value of buf was used before it was changed, but the rest were unnecessary. There was one list_for_each+list_entry loop that wasn't changed, since it depending on the loop iterator being left as NULL if the list was empty. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> CC: Hans Verkuil <hverkuil@xs4all.nl>
2007-10-24Remove the obsoleted xc3028Mauro Carvalho Chehab
From: Mauro Carvalho Chehab <mchehab@infradead.org> Remove the old xc3028.c file, replacing all occurrences of TUNER_XCEIVE_XC3028 to TUNER_XC2028. Some work is still may be required to make sure that non-tm6000 drivers will be capable of using tuner-xc2028. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org> --- linux/Documentation/video4linux/CARDLIST.tuner | 2 +- linux/drivers/media/video/em28xx/em28xx-cards.c | 10 +++------- linux/drivers/media/video/ivtv/ivtv-cards.c | 6 +++--- linux/drivers/media/video/ivtv/ivtv-driver.c | 2 +- linux/drivers/media/video/tuner-core.c | 5 ----- linux/drivers/media/video/tuner-types.c | 6 +++--- linux/include/media/tuner.h | 2 +- v4l/Makefile | 4 ---- 8 files changed, 12 insertions(+), 25 deletions(-)
2007-08-26ivtv: move ivtv.h public header to include/linux.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-28ivtvfb: fix an obvious bug in ivtvfb_release_buffers()Hans Verkuil
From: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-28ivtvfb: replace ivtv_fb prefix to ivtvfb, change warning to info message.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-26ivtvfb: rename some missed ivtv-fb references to ivtvfb.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-26ivtvfb: renamed ivtv-fb to ivtvfb, move header to include/linuxHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> The convention for framebuffer devices is to call them xxxfb, not xxx-fb. Conform to this. Also move the ivtvfb.h header to include/linux: it is a public header. The FBIO_WAITFORVSYNC ioctl is now also defined in the ivtvfb.h header, no more need to include matroxfb.h for just this ioctl. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-26ivtv-fb: add missing FBIO_WAITFORVSYNC ioctl defineHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-25ivtv: finish VBI related cleanup.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-25ivtv: VBI cleanups and fixesHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Besides some VBI cleanups this patch also fixes a subtle problem with the VBI re-insertion stream where the PIO work handler wasn't called quickly enough, resulting in occasional corrupt data. Furthermore the CC output didn't disable CC correctly and at the right time, causing duplicates to be sent. An saa7127 fix for VPS output was also added: the wrong data was sent. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-25ivtv/ivtv-fb: improve locking to prevent ivtv/ivtv-fb initialization problems.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-27merge: http://linuxtv.org/hg/~hverkuil/v4l-dvbMauro Carvalho Chehab
From: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-26ivtv: udelay for the i2c bus was set too highHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> An udelay of 5 is sufficient for standard speed i2c busses, 10 make it too slow. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-25ivtv: use new videodev2.h pixel formatsHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-24merge: http://linuxtv.org/hg/~hverkuil/v4l-dvbMauro Carvalho Chehab
From: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-24ivtv: kzalloc() returns void pointer, no need to castHans Verkuil
From: Jesper Juhl <jesper.juhl@gmail.com> Since kzalloc() returns a void pointer, we don't need to cast the return value in drivers/media/video/ivtv/ivtv-queue.c Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-24ivtv: set correct pixel format and alpha properties in VIDIOC_G_FBUFHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-23ivtv: fix V4L2_ENC_CMD_STOP_AT_GOP_END supportHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Support for V4L2_ENC_CMD_STOP_AT_GOP_END was broken. While the driver correctly waited for the card to capture until the GOP was complete, afterwards the driver buffers were just flushed instead of waiting for the application to read all the pending data. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-23ivtv: fix VIDIOC_G_ENC_INDEX flag handlingHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Due to a documentation bug (the type mask is 3 bits long, not 2) the wrong frame types were filled in: the B and P frame types were swapped. This bug also hid a second bug: when a capture is stopped a last entry is written into the pgm index buffer with internal type 0, denoting the end of the program. This entry wasn't ignored, instead it was accidentally returned to the caller as a P frame. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-23ivtv: more ivtv-driver.h cleanups.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-23ivtv: reorganized and cleanup ivtv structHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-23ivtv: more cleanups, merged ivtv-audio.c and ivtv-video.c into ivtv-routing.cHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-23ivtv: header cleanupHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> - add guards - remove unused header includes - move card-specific stuff from ivtv-driver.h to ivtv-cards.h - move YUV-specific stuff from ivtv-driver.h to ivtv-yuv.h Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-22ivtv-fb: correct transparency bit reporting.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-22ivtv: log in status if framebuffer uses YUV instead of RGBHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-21cx2341x: some controls should not be changed while the device is busy.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> The driver should now pass the 'busy' state of the device to the cx2341x module whenever controls are set or tried. -EBUSY will be returned if the device is busy and the user attempts to modify certain 'dangerous' controls. It concerns controls that change the audio or video compression mode and bitrates. The cx88-blackbird and pvrusb2 drivers currently always pass '0' (not busy) to the cx2341x, effectively keeping the old behavior for now. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-23From: Jean Delvare <khali@linux-fr.org>Mauro Carvalho Chehab
Subject: ivtv: Fix static structure initialization Date: Thu, 23 Aug 2007 19:32:26 +0200 Convert the initialization of ivtv_i2c_algo_template to C99-style. Otherwise a future change to struct i2c_algo_bit_data would break this code. Also declared that structure const - it's a template after all. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-21Cleanup: remove linux/moduleparam.h from drivers/media filesMauro Carvalho Chehab
From: Mauro Carvalho Chehab <mchehab@infradead.org> Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This patch removes all occurences of moduleparm.h from drivers/media files. Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-08-20ivtv: prevent changing VBI format while capture is in progress.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Changing the VBI format requires a CX2341X_ENC_INITIALIZE_INPUT firmware call. This can only be done if no capture is in progress. So return -EBUSY if the encoder is busy. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-20ivtv: fix output mode processing: UDMA_YUV wasn't cleared.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> - Always clear when stopping the decoder - Clear if the filehandle that is being close was used for UDMA_YUV output. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv: add VIDIOC_OVERLAYHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Add VIDIOC_OVERLAY to enable/disable the OSD. Also add the OSD state to the log status report. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv: fix IVTV_IOC_DMA_FRAME bug introduced by highmem bugfix.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> The return value of ivtv_udma_fill_sg_list() was changed by the highmem bugfix, but that return value was still used in ivtv-yuv.c. Revert to the old return value, but in addition return -1 in case of a memory allocation error. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv: log stereo/bilingual audio modesHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv: add support for highmem udmaHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> When trying to DMA userspace buffers to the cx23415 you need to check whether the page is in highmem. If this is the case, then bounce buffers have to be used to allow DMA. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv-fb: remove unused header includes.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv: move serialization to the fileops level.Hans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Serialization is now done on the open/close/ioctl level and also when the read/write/poll start an encoder/decoder stream. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv: improve debug messagesHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> - add FILE debug flag for open/close/read/write/poll. - show cmd for encoder/decoder command ioctl. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv: specify some stream sizes in kB instead of MBHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> Some streams (PCM, VBI decoding) do not need that much memory, so specify the allocated memory in kB instead of MB to limit memory usage. E.g. 1 MB is overkill for the VBI decoding stream, 64 kB is enough. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-19ivtv: setup TV output standard on init to prevent flickerHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> The TV output standard was set only on first use, which meant that the saa7127 was set to NTSC until then, leading to flickering on PAL systems. Since the saa7127 has no firmware it is OK to initialize it immediately. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-18ivtv: fix udma yuv bugHans Verkuil
From: Ian Armstrong <ian@iarmst.demon.co.uk> Using udma yuv causes the driver becomes locked into that mode. This prevents use of the mpeg decoder & non-udma yuv output. This patch clears the operating mode when the device is closed. Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2007-08-18ivtv: retry/timer improvementsHans Verkuil
From: Hans Verkuil <hverkuil@xs4all.nl> - Give up frame after three retries. - When the last capture/decode ends, make sure to delete the dma_timer. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-08 18:13:35 +0000