| Age | Commit message (Collapse) | Author |
|---|
|
From: Suresh Siddha <suresh.b.siddha@intel.com>
Impact: driver could possibly stomp on resources outside of its scope
{mchehab@redhat.com: I got two versions of the same patch (identical,
except for whitespacing). One authored by Andy Burns and another
authored by Suresh Siddha. Due to that, I'm applying the one that has
less CodingStyle errors. I'm also adding both comments and the SOB's for
both patches, since they are both interesting}
Suresh Siddha commented:
Alexey Fisher reported:
> resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000
> 0xcfefffff PCI Bus 0000:01
BAR base is located in the middle of the 4K page and the hardcoded
size argument makes the request span two pages causing the conflict.
Fix the hard coded size argument in ioremap().
Andy Burns commented:
I have already sent this patch on the linux-dvb list, but it didn't get
much attention, so re-sending direct, I hope you all don't mind.
While attempting to run mythtv in a xen domU, I encountered problems
loading the driver for my saa7134 card, with an error from ioremap().
This error was due to the driver allocating an incorrectly sized mmio
area, which was trapped by xen's permission checks, but this would go
un-noticed on a kernel without xen.
My card has a 1K sized mmio area, I've had information that other cards
have 2K areas, perhaps others have different sizes, yet the driver
always attempts to map 4K. I realise that the granularity of mapping is
the page size, which typically would be 4K, but unless the card's base
address happens to fall on a 4K boundary (mine does not) then the
base+4K will end up spanning two pages, and this is when the error
occurs under xen.
My patch uses the pci_resource_len macro to determine the size required
for the user's particular card, instead of the hardcoded 4K value. I've
tested with a couple of printk() inside ioremap() that the start address
and size do get rounded to the closest page boundary.
With this patch I am able to successfully load the saa7134 driver and
run mythtv under xen with my card, subject to correct pollirq settings
in case of shared IRQ, I am still seeing occasional DMA panics, which I
think are related to swiotlb handling by dom0/domU, usually the panic
occurs when changing mux, once tuned to a mux, 12 hour continuous
recordings are possible without errors.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andy Burns <andy@burns.net>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jonathan Corbet <corbet@lwn.net>
Remove lock_kernel() call from cafe_ccic.c
Commit d56dc61265d2527a63ab5b0f03199a43cd89ca36 added lock_kernel()
calls to cafe_ccic.c. But that driver was written with proper locking
and does not need the BKL, so take it back out.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Gregor Jasny <jasny@vidsoft.de>
This patch adds the missing compat ioctls that are needed to
operate Skype in combination with libv4l and a MJPEG only camera.
If you think it's trivial enough please submit it to -stable, too.
Signed-off-by: Gregor Jasny <gjasny@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by David Ellingsworth:
> I'm not sure if it matters or not, but the ibmcam driver in the
> Mauro's linux-2.6 git tree in the for_linus branch is currently
> broken.
uvd is equal to NULL during most of ibmcam_probe. Due to that, an OOPS
is
generated at dev_info. This patch replaces uvd->dev->dev to dev->dev
inside this routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reviewed-by: David Ellingsworth <david@identd.dyndns.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Author: Johannes Berg <johannes@sipsolutions.net>
remove CONFIG_KMOD from drivers
Straight forward conversions to CONFIG_MODULE; many drivers
include <linux/kmod.h> conditionally and then don't have any
other conditional code so remove it from those.
kernel-sync:
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Author: David Woodhouse <David.Woodhouse@intel.com>
Define and use PCI_DEVICE_ID_MARVELL_88ALP01_CCIC for CAFÉ camera driver
Also, stop looking at the NAND controller (0x4100) and checking the
device class. For a while during development, all three functions on the
chip had the same ID. We made them fix that fairly promptly, and we can
forget about it now.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Author: Greg Kroah-Hartman <gregkh@suse.de>
USB: remove warn() macro from usb media drivers
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
kernel-sync:
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Author: Harvey Harrison <harvey.harrison@gmail.com>
byteorder: remove direct includes of linux/byteorder/swab[b].h
A consolidated implementation will provide this generically through
asm/byteorder, remove direct includes to avoid breakage when the
changeover to the new implementation occurs.
kernel-sync:
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
inode is never used on video_ioctl2. Remove it and rename the function to
__video_ioctl2. This allows its usage directly as a callback at
fops.unlocked_ioctl.
Since we still need a callback with inode to be used with fops.ioctl,
this patch adds video_ioctl2() that is just a call to __video_ioctl2().
Also, this patch adds some comments about video_ioctl2 and __video_ioctl2
usage at v4l2-ioctl.h.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Darron Broad <darron@kewl.org>
De-alloc frontends on fault condition.
Priority: normal
Signed-off-by: Darron Broad <darron@kewl.org>
|
|
From: Darron Broad <darron@kewl.org>
This creates a self contained frontend de-allocator
for the instances where an adapter has not been
registered yet frontend de-allocation may
be required.
Priority: normal
Signed-off-by: Darron Broad <darron@kewl.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
The inode parameter at v4l_compat_translate_ioctl() were just passed over several
places just to keep compatible with fops.ioctl. However, it weren't used anywere.
This patch gets hid of this unused parameter.
Priority: normal
CC: Laurent Pinchart <laurent.pinchart@skynet.be>
CC: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Darron Broad <darron@kewl.org>
Add debug output for dvb_remove enter.
Priority: normal
Signed-off-by: Darron Broad <darron@kewl.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
The multifrontend changes on cx88 assumed that all boards that use cx88-mpeg
supports DVB. This is not true. There also a few analog-only boards based on
Blackboard design that also uses cx88-mpeg. For those boards, there's no need
to allocate dvb frontends.
This patch fixes videobuf allocation for those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Darron Broad <darron@kewl.org>
Initial fix for when analogue only is selected
for compilation (ie, !CX88_DVB)
Priority: normal
Signed-off-by: Darron Broad <darron@kewl.org>
|
|
From: Ian Armstrong <ian@iarmst.demon.co.uk>
When using FBIOBLANK, FB_BLANK_POWERDOWN will now switch off the video output.
Since some televisions turn themselves off after a while with no signal, this
is the closest we can get to power-saving.
Priority: normal
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The kernel number of a v4l2 node (e.g. videoX, radioX or vbiX) is now
independent of the minor number. So instead of using the minor field
of the video_device struct one has to use the num field: this always
contains the kernel number of the device node.
I forgot about this when I did the v4l2 core change, so this patch
converts all drivers that use it in one go. Luckily the change is
trivial.
Priority: high
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CC: michael@mihu.de
CC: mchehab@infradead.org
CC: corbet@lwn.net
CC: luca.risolia@studio.unibo.it
CC: isely@pobox.com
CC: pe1rxq@amsat.org
CC: royale@zerezo.com
CC: mkrufky@linuxtv.org
CC: stoth@linuxtv.org
|
|
From: Martin Dauskardt <martin.dauskardt@gmx.de>
When loading ivtv the TV-out of the PVR-350 will flash green since the
saa712x is activated before the MPEG decoder has been initialized.
Deactivate the saa712x until the MPEG decoder has been initialized.
Priority: normal
Signed-off-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Based on an older patch from Sakari Ailus.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CC: Sakari Ailus <sakari.ailus@nokia.com>
|
|
From: Sakari Ailus <sakari.ailus@nokia.com>
Export v4l2_int_device_try_attach_all. This allows initiating the
initialisation of int if device after the drivers have been registered.
Also allow drivers to call ioctls if v4l2-int-if was compiled as
module.
Priority: normal
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Boris Dores <babal@via.ecp.fr>
(Mike Isely) This change was empirically figured out by Boris Dores
after empirically comparing against behavior in the Windows driver.
Priority: normal
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Mike Isely <isely@pobox.com>
Fix deadlock problem in 2.6.27 caused by new USB core behavior in
response to a USB device reset request. With older kernels, the USB
device reset was "in line"; the reset simply took place and the driver
retained its association with the hardware. However now this reset
triggers a disconnect, and worse still the disconnect callback happens
in the context of the caller who asked for the device reset. This
results in an attempt by the pvrusb2 driver to recursively take a
mutex it already has, which deadlocks the driver's worker thread.
(Even if the disconnect callback were to happen on a different thread
we'd still have problems however - because while the driver should
survive and correctly disconnect / reconnect, it will then trigger
another device reset during the repeated initialization, which will
then cause another disconect, etc, forever.) The fix here is simply
to not attempt the device reset (it was of marginal value anyway).
Priority: normal
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Andy Walls <awalls@radix.net>
Changes to let error return codes bubble up to the user visible
error message on card initialization. A number of them were being remapped to
ENOMEM when no memory or array resource shortage existed. That hampered
diagnosis of user trouble reports.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
cx18: Add __iomem address space qualifier to cx18_log_*_retries() addr
argument to clean up sparse build warnings.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
On error exit, the cx18_probe() function did not use the proper entry in
cx18_cards[] with kfree() when card init failed; leaking memory.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Igor M. Liplianin <liplianin@me.by>
Remove warning message during cx88-dvb compilation.
Also fixes double underline in function and struct names.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch marks those two functions as static:
static int videobuf_dvb_register_adapter(struct videobuf_dvb_frontends *fe,
static int videobuf_dvb_register_frontend(struct dvb_adapter *adapter,
Since MFE patches changed their calls by videobuf_dvb_register_bus.
To avoid having to declare the prototypes, the patch moves
videobuf_dvb_register_bus() to be after the declaration of the above functions
used there.
Priority: normal
CC: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Leandro Costantino <lcostantino@gmail.com>
Priority: normal
Signed-off-by: Leandro Costantino <lcostantino@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
|
|
|
|
From: Steven Toth <stoth@linuxtv.org>
MFE: videobuf-dvb.c checkpatch cleanup as part of MFE merge
Priority: normal
Signed-off-by: Steven Toth <stoth@linuxtv.org>
|
|
From: Erik Andren <erik.andren@gmail.com>
Priority: normal
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Erik Andren <erik.andren@gmail.com>
Priority: normal
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Erik Andren <erik.andren@gmail.com>
Priority: normal
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Erik Andren <erik.andren@gmail.com>
Priority: normal
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Erik Andren <erik.andren@gmail.com>
Priority: normal
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
