| Age | Commit message (Collapse) | Author |
|---|
|
From: Andy Walls <awalls@radix.net>
Add DVB-T support for Yuan MPC-718 cards with an MT352 or ZL10353 demodulator.
There are apparently some units with a DiBcom demodulator which could be
supported by one of the dib7000 modules - but this is not implemented in the
cx18 driver (yet).
Due to lack of porgramming details for the MT352 and the mt352 module requiring
a "demod_init" function, a "firmware" must be obtained and loaded to get
DVB-T working for Yuan MPC-718 cards with an MT352.
Priority: normal
Tested-by: Steve Firth <firth650@btinternet.com>
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Discovered the bug that were limiting the output format to just RGB565.
Now, it is possible to output image at Bayer format (the original one,
as generated by Silvercrest sensor, and two others), and also on YUY.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Andy Walls <awalls@radix.net>
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Webcams have different constraints than other v4l devices. This patch
makes the format ioctls to behave better. It also fixes a bug at open()
handler, that were always reseting resolution to the maximum available
one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for pointing this issue on
my last patch.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Huang Weiyi <weiyi.huang@gmail.com>
Remove unused #include <linux/version.h>'s in drivers/media/video/adv7343.c.
Priority: normal
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
CC: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Roel Kluin <roel.kluin@gmail.com>
input, inp and i are unsigned. When negative they are wrapped and caught by the
other test.
Priority: normal
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
CC: Andy Walls <awalls@radix.net>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Joe Perches <joe@perches.com>
Priority: normal
Signed-off-by: Joe Perches <joe@perches.com>
CC: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Joe Perches <joe@perches.com>
Priority: normal
Signed-off-by: Joe Perches <joe@perches.com>
CC: Patrick Boettcher <patrick.boettcher@desy.de>
CC: Steven Toth <stoth@linuxtv.org>
CC: Igor M. Liplianin <liplianin@netup.ru>
CC: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Joe Perches <joe@perches.com>
Priority: normal
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Erik Andrén <erik.andren@gmail.com>
Priority: high
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
- call a new subdriver function 'isoc_init' before chosing the first
alternate setting.
- call a new subdriver function 'isoc_nego' when submitting the URBs failed.
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Only the back sensor (mi1320_soc) is usable.
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Laurent Pinchart <laurent.pinchart@skynet.be>
To make UVC constants accessible by a future UVC gadget driver, move them from
drivers/media/video/uvc/uvcvideo.h to include/linux/usb/video.h.
Priority: normal
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
|
|
From: Laurent Pinchart <laurent.pinchart@skynet.be>
Those constants are not used anymore, remove them.
Priority: normal
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
|
|
From: Laurent Pinchart <laurent.pinchart@skynet.be>
In preparation to moving UVC constants to a public location, prefix all
constants with UVC_ to avoid namespace clashes.
Priority: normal
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
|
|
From: Laurent Pinchart <laurent.pinchart@skynet.be>
uvcvideo.h redefines class-specific descriptor types already present in
usb/ch9.h. Remove the duplicated definitions and use the ones from usb/ch9.h.
Priority: normal
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
|
|
From: Erik Andrén <erik.andren@gmail.com>
All hdcs registers use bit 0 as a read/write flag and needs to be shifted one bit to the left. This wasn't accounted for when doing a sequence of writes.
Priority: high
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
|
|
From: Erik Andrén <erik.andren@gmail.com>
Priority: high
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Chaithrika U S <chaithrika@ti.com>
mutex_lock_interruptible return value has to be handled properly to indicate
the status to the higher layers of the kernel.
Priority: normal
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mike Isely <isely@pobox.com>
This change does not change any outward behavior; it merely chops down
some large if-conditions with embedded assignments into something a
little more maintainable for others (I of course never had a problem
with this...).
Priority: normal
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Mike Isely <isely@pobox.com>
The pvrusb2 driver has a concept of "routing scheme" which defines
which physical inputs should be connected based on application's
choice of logical input. The correct "routing scheme" depends on the
specific device since different devices might wire up their muxes
differently - it can't be coded into the sub-device driver and it
can't be just a single setting in the pvrusb2 driver since the driver
handles multiple different devices. This concept has been in place
for a while and works, however there are cases where a specific input
for a specific device has no route - previously due to an oversight
this was handled badly. With these changes the driver can now
specifically recognize cases where there is no defined route for a
given input.
Priority: normal
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Mike Isely <isely@pobox.com>
Change default frequency to be US Broadcast channel 3 - with the
transition to d igital the previous value has now become useless.
This change is PURELY to help with my testing (I need to set some kind
of default so it might as well be some thing usable).
Priority: normal
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Mike Isely <isely@pobox.com>
The cx25840 module's VBI initialization logic uses the current video
standard as part of its internal algorithm. This therefore means that
we probably need to make sure that the correct video standard has been
set before initializing VBI. (Normally we would not care about VBI,
but as described in an earlier changeset, VBI must be initialized
correctly on the cx25840 in order for the chip's hardware scaler to
operate correctly.)
It's kind of messy to force the video standard to be set before
initializing VBI (mainly because we can't know what the app really
wants that early in the initialization process). So this patch does
the next best thing: VBI is re-initialized after any point where the
video standard has been set.
Priority: high
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Mike Isely <isely@pobox.com>
The cx25840 module requires that its VBI initialization entry point be
called in order for hardware-scaled video capture to work properly -
even if we don't care about VBI. Making this behavior even more
subtle is that if the capture resolution is set to 720x480 - which is
the default that the pvrusb2 driver sets up - then the cx25840
bypasses the hardware scaler. Therefore this problem does not
manifest itself until some other resolution, e.g. 640x480, is tried.
MythTV typically defaults to 640x480 or 480x480, which means that
things break whenever the driver is used with MythTV.
This all has been known for a while (since at least Nov 2006), but
recent changes in the pvrusb2 driver (specifically in regards to
sub-device support) caused this to break again. VBI initialization
must happen *after* the chip's firmware is loaded, not before. With
this fix, 24xxx devices work correctly again.
A related fix that is part of this changeset is that now we
re-initialize VBI any time after we issue a reset to the cx25840
driver. Issuing a chip reset erases the state that the VBI setup
previously did. Until the HVR-1950 came along this subtlety went
unnoticed, because the pvrusb2 driver previously never issued such a
reset. But with the HVR-1950 we have to do that reset in order to
correctly transition from digital back to analog mode - and since the
HVR-1950 always starts in digital mode (required for the DVB side to
initialize correctly) then this device has never had a chance to work
correctly in analog mode! Analog capture on the HVR-1950 has been
broken this *ENTIRE* time. I had missed it until now because I've
usually been testing at the default 720x480 resolution which does not
require scaling... What fun. By re-initializing VBI after a cx25840
chip reset, correct behavior is restored.
Priority: high
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The variable 'rc' could be used uninitialized in the cx231xx_capture_start
function. Sri informed me that it should be initialized to -1.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
tcm825x_remove is not necessarily called on module exit, it can also be
called when the i2c_adapter is removed. While the i2c adapter might never
be removed on an embedded system, in practice this sensor driver can also
be used in e.g. a USB webcam where this is a perfectly acceptable thing
to do.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Muralidharan Karicheri <m-karicheri2@ti.com>
This adds Makefile and Kconfig changes to build vpfe capture driver.
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Priority: normal
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Muralidharan Karicheri <m-karicheri2@ti.com>
This is a new module added for vpss library functions that are
used for configuring vpss system module. All video drivers will
include vpss.h header file and call functions defined in this
module to configure vpss system module.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Priority: normal
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Muralidharan Karicheri <m-karicheri2@ti.com>
This is the hw module for DM644x CCDC. This registers with the
vpfe capture driver and provides a set of hw_ops to configure
CCDC for a specific decoder device connected to the VPFE.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Priority: normal
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Muralidharan Karicheri <m-karicheri2@ti.com>
Adds ccdc hw module for DM355 CCDC. This registers with the bridge
driver a set of hw_ops for configuring the CCDC for a specific
decoder device connected to vpfe.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Mauro Carvalho Chehab <mchehab@infradead.org>
Priority: normal
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Muralidharan Karicheri <m-karicheri2@ti.com>
Adds ccdc hw device header for vpfe capture driver
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Priority: normal
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Muralidharan Karicheri <m-karicheri2@ti.com>
This the vpfe capture bridge driver for doing video
capture on DM355 and DM6446 evms. The ccdc hw modules register with the
driver and are used for configuring the CCD Controller for a specific
decoder interface. The driver also registers the sub devices required
for a specific evm. More than one sub devices can be registered.
This allows driver to switch dynamically to capture video from
any sub device that is registered. Currently only one sub device
(tvp5146) is supported. But in future this driver is expected
to do capture from sensor devices such as Micron's MT9T001, MT9T031
and MT9P031 etc. The driver currently supports MMAP based IO.
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Priority: normal
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Muralidharan Karicheri <m-karicheri2@ti.com>
Fix documentation style based on comments from Mauro.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Priority: normal
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Muralidharan Karicheri <m-karicheri2@ti.com>
This patch converts TVP514x driver to sub-device framework
from V4L2-int framework.
Priority: normal
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Hardik Shah <hardik.shah@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
[hverkuil@xs4all.nl: remove inline from the dump_reg function]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans de Goede <hdegoede@redhat.com>
Name saturation control saturation, not color and make the default
less saturated (the old default was overdoing it).
Priority: normal
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
From: Hans de Goede <hdegoede@redhat.com>
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise
the picture is upside down. It is better to instead invert the meaning
of the control in the set function, and have the default be no vflip,
as one would expect vflip enabled to be upside down.
Priority: normal
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
From: Hans de Goede <hdegoede@redhat.com>
gspca_sonixj: Add light frequency control
Priority: normal
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
From: Hans de Goede <hdegoede@redhat.com>
gspca_sonixj: enable autogain control for the ov7620, and not only
make it enable autogain but also auto exposure (and do the
same for the ov7648).
Priority: normal
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
From: Hans de Goede <hdegoede@redhat.com>
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer
overflows during my testing of a "Premier" 0c45:613e cam
Priority: normal
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
From: Hans de Goede <hdegoede@redhat.com>
Mark the v4l1 uvcvideo quickcam messenger driver as deprecated, the one
cam it supports, is now also supported by the v4l2 gspca stv06xx driver.
Priority: normal
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
