| Age | Commit message (Collapse) | Author |
|---|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
According to the engineer at PCTV Systems, the xc5000 reset pin is supposed
to be on GPIO12. However, despite three nights of effort, pulling that GPIO
low didn't reset the xc5000. While pulling MO_SRST_IO low does reset the
xc5000, this also resets in the s5h1409 being reset as well. This causes
tuning to always fail since the internal state of the s5h1409 does not match
the driver's state.
Given that the only two conditions in which the driver performs a reset is
during firmware load and powering down the chip, I am taking out the reset.
We know that the chip is being reset when the cx88 comes online, and not being
able to do power management for this board is better than not having any
tuning at all.
Problem discovered when implementing proper power management for the xc5000,
which results in calls to the reset callback *after* s5h1409 is initialized.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: Chaogui Zhang <czhang1974@gmail.com>
|
|
From: Cohen David.A <david.cohen@nokia.com>
Change kmalloc()/kfree() to vmalloc()/vfree() for sglist allocation
during videobuf_dma_map() and videobuf_dma_unmap()
High resolution sensors might require too many contiguous pages
to be allocated for sglist by kmalloc() during videobuf_dma_map()
(i.e. 256Kib for 8MP sensor).
In such situations, kmalloc() could face some problem to find the
required free memory. vmalloc() is a safer solution instead, as the
allocated memory does not need to be contiguous.
Signed-off-by: David Cohen <david.cohen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Filipe Rosset <rosset.filipe@gmail.com>
Update the 17ef:480b device comment to list Lenovo Thinkpad SL400.
Priority: low
Signed-off-by: Filipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
|
|
From: Laurent Pinchart <laurent.pinchart@skynet.be>
Most UVC camera include an interrupt endpoint to report control value changes,
video streaming errors and camera button events. The USB controller
continuously polls the interrupt endpoint to retrieve such events. This
prevents the device from being auto-suspended, and thus consumes power.
Reporting video streaming errors don't make sense when the V4L2 device is
closed. Control value changes are probably useless as well if nobody listens to
the events, although caching will probably have to be completely disabled then.
No polling is thus be required when /dev/videoX is not opened.
To enable auto-suspend and save power do not poll the interrupt endpoint until
the device is open. We lose the ability to detect button events if no
application is using the camera.
http://bugzilla.kernel.org/show_bug.cgi?id=11948
Priority: normal
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
|
|
From: Randy Dunlap <randy.dunlap@oracle.com>
Build fails when CONFIG_I2C=n, so handle that case in the if block:
drivers/built-in.o: In function `v4l2_device_unregister':
(.text+0x157821): undefined reference to `i2c_unregister_device'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Randy Dunlap <randy.dunlap@oracle.com>
soc_camera uses i2c_*() functions and has build errors when CONFIG_I2C=n:
ERROR: "i2c_new_device" [drivers/media/video/soc_camera.ko] undefined!
ERROR: "i2c_get_adapter" [drivers/media/video/soc_camera.ko] undefined!
ERROR: "i2c_put_adapter" [drivers/media/video/soc_camera.ko] undefined!
ERROR: "i2c_unregister_device" [drivers/media/video/soc_camera.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/Kconfig | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
|
|
From: Andy Walls <awalls@radix.net>
Initial changes to get sliced VBI for 625 line system working. This is patch
is untested.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Mike Isely <isely@pobox.com>
Priority: normal
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
modpost needs a __refdata marker in driver structs to ensure references to
.probe and .remove functions from .devinit.text and .devexit.text sections
respectively are valid. Add __refdata to soc_camera_pdrv platform driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/soc_camera.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Andy Walls <awalls@radix.net>
The TCL MNM05-04 is used on some HVR-1600 models. It appears to be
similar to the TCL MFMN05-4 but without FM radio. The
TUNER_PHILIPS_FM1236_MK3 tuner definition appears to be the proper existing
tuner definition to use for this tuner.
Reported-by: Matt Beadon <matt.beadon@gmail.com>
Priority: normal
Tested-by: Matt Beadon <matt.beadon@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
|
|
From: figo.zhang <figo.zhang@kolorific.com>
when re-open or re-start (video_streamon), the q->curr would not be NULL in saa7134_buffer_queue(),
and all the qbuf will add to q->queue list,no one to do activate to start DMA,and then no interrupt
would happened,so it will be block.
In VIDEOBUF_NEEDS_INIT state, initialize the curr pointer to be NULL in the buffer_prepare().
Signed-off-by: Figo.zhang <figo.zhang@kolorific.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression caused by changeset 9133:64aed7485a43 - v4l: disconnect
kernel number from minor
Before the above changeset, ov511_probe used to allow forcing to use a
certain specific set of video devices, like:
modprobe ov511 unit_video=4,1,3 num_uv=3
So, assuming that you have 5 ov511 devices, and connect they one by one,
they'll gain the following device numbers (at the connection order):
/dev/video4
/dev/video1
/dev/video3
/dev/video0
/dev/video2
However, this was changed due to this change at video_register_device():
+ nr = find_next_zero_bit(video_nums[type], minor_cnt, nr == -1 ? 0 : nr);
With the previous behavior, a trial to register on an already allocated mirror
would fail, and a loop would get the next requested minor. However, the current
behavior is to get the next available minor instead of failing. Due to that,
this means that the above modprobe parameter will give, instead:
/dev/video5
/dev/video6
/dev/video7
/dev/video8
/dev/video9
In order to restore the original behavior, a static var were added,
storing the amount of already registered devices.
While there, it also fixes the locking of the probe/disconnect functions.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Since i2c autoprobing is no longer supported by v4l2 we need to make sure
that the i2c modules are linked before the v4l2 modules. The v4l2 modules
now rely on the presence of the i2c modules, so these must have initialized
themselves before the v4l2 modules.
The exception is the ir-kbd-i2c module, which is the only one still using
autoprobing. This one should be loaded at the end of the v4l2 module. Loading
it earlier actually causes problems with tveeprom. Once ir-kbd-i2c is no
longer autoprobing, then it has to move up as well.
This is only an issue when everything is compiled into the kernel.
Thanks to Marcus Swoboda for reporting this and Udo Steinberg for testing
this patch.
Priority: high
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Udo A. Steinberg <udo@hypervisor.org>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
The scan of the image packets of the sensor ov772x was broken when
the sensor ov965x was added.
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Erik Andrén <erik.andren@gmail.com>
The quirk list has grown and was in need of sorting. This is now done. Add a new vflip quirk for the ASUS A7V while we're at it. Thanks to Carsten Menzel for reporting.
Priority: normal
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
|
|
From: Roel Kluin <roel.kluin@gmail.com>
With `while (try_count-- > 0)' try_count reaches -1 after the loop.
Priority: normal
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Lennart Poettering <mzxreary@0pointer.de>
A bunch of V4L drivers generate BTN_0 instead of KEY_CAMERA key presses.
X11 is able to handle KEY_CAMERA automatically these days while BTN_0 is
not treated at all. Thus it would be of big benefit if the camera drivers
would consistently generate KEY_CAMERA. Some drivers (uvc) already do,
this patch updates the remaining drivers to do the same.
I only possess a limited set of webcams, so this isn't tested with all
cameras. The patch is rather trivial and compile tested, so I'd say it's
still good enough to get merged.
Priority: normal
Signed-off-by: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Alan Cox <alan@linux.intel.com>
Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13435
Priority: normal
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Figo.zhang <figo1802@gmail.com>
vfree() does it's own NULL checking,so no need for check before
calling it.
Priority: normal
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Figo.zhang <figo1802@gmail.com>
it is better return -ENOMEM than -EIO
Priority: normal
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Hans de Goede <hdegoede@redhat.com>
Priority: normal
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
In cases where the device does not actually provide a USB audio class *or*
vendor audio, do not load the driver that provides vendor audio support (such
as the KWorld 2800d). Otherwise, the /dev/audio1 device file gets created and
users get confused.
Also, reworks the logic a bit so that we don't try to inspect the register
content if the register read failed entirely.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Andy Walls <awalls@radix.net>
This adds support for DVB-T on the Leadtek DVR3100 H and should also get analog
TV capture from the tuner working properly as well.
DVB-T 6 MHz and 8 MHz have been tested and verified to work by Terry Wu of
Leadtek. DVB-T 7 MHz has also been verified working with a change developed by
Terry to the tuner-xc2028.c driver.
Special thanks go to Terry Wu <terrywu2009@gmail.com> of Leadtek who provided
the needed information and testing to get digital TV working for the Leadtek
DVR3100 H.
Reported-by: Terry Wu <terrywu2009@gmail.com>
Priority: normal
Tested-by: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
