| Age | Commit message (Collapse) | Author |
|---|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Some ioctls have structs that are a different size depending on what type
of buffer is being used. If the buffer type leaves a field unused or has
padding space at the end, this space should be zeroed out.
The problems with S_FMT and REQBUFS were original identified and patched by
Márton Németh <nm127@freemail.hu>.
Priority: normal
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
For a number of different ioctls, the v4l2-ioctl code checks that the
passed buffer type is supported by the driver. It did this by checking
that the driver defined a method for the try_fmt handler for that buffer
type. However, try_fmt is optional and a driver might not provide it even
though it does support that type. So use g_fmt instead, since that isn't
optional.
This should fix a problem with VBI capture with saa7146.
Priority: normal
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
If someone requests a format at fmt->index == (unsigned)-1 and the first
format in the array doesn't have the requested type then num will still be
-1 when it's compared to fmt->index and there will appear to be a match.
Restructure the loop so this can't happen. It's simpler this way too. The
unnecessary check for (unsigned)fmt->index < 0 found by Roel Kluin
<roel.kluin@gmail.com> is removed this way too.
Priority: normal
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Dean Anderson <dean@sensoray.com>
Error count in read pipe completion corrected.
URB not resubmitted if shutting down.
URB not freed in completion routine if new urb_submit_fails.
(URB is freed on shutdown).
Priority: high
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean Delvare <khali@linux-fr.org>
The new i2c binding model doesn't use i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Steven Toth <stoth@linuxtv.org>
cx23885: Don't assume GPIO interrupts are cam related.
Priority: normal
Signed-off-by: Steven Toth <stoth@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
kernel-sync:
Author: David Vrabel <david.vrabel@csr.com>
Date: Wed Apr 8 17:36:28 2009 +0000
USB: add reset endpoint operations
Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit. So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).
usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.
If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
CC: Mike Isely <isely@isely.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
kernel-sync:
Author: Martin Fuzzey <mfuzzey@gmail.com>
Date: Tue Apr 21 21:48:09 2009 +0200
USB: pwc : do not pass stack allocated buffers to USB core.
This is causes problems on platforms that have alignment requirements
for DMA transfers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Németh Márton <nm127@freemail.hu>
The V4L2 ioctls usually return 0 when the operation was successful
and -1 in case of error. Currently VIDIOC_REQBUFS returns the
number of buffers which is redundant because this information is
available in count field of struct v4l2_requestbuffers. The
V4L2 API specification, revision 0.24 [1] explicitly specifies for
VIDIOC_REQBUFS that the return value shall be 0 on success.
The patch was tested with v4l-test 0.13 [2] with vivi driver.
References:
[1] V4L2 API specification, revision 0.24
http://v4l2spec.bytesex.org/spec/r13696.htm
[2] v4l-test: Test environment for Video For Linux Two API
http://v4l-test.sourceforge.net/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Pieter Van Schaik <vansterpc@gmail.com>
This patch is for supporting the remote control of the Winfast TV2000
XP Global TV capture card. A case statement was added in order to
initialize the GPIO data structures as well as a case statement for
handling the keys correctly when pressed.
Thanks to Hermann and Mauro for all the help
Signed-off-by: Pieter C van Schaik <vansterpc@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Dmitri Belimov <d.belimov@gmail.com>
When we capture signal from composite input offen lost and found syncro
sequence. In this case the MPEG coder hardware reset after each
lost/found event. The image has a lot of artefactes. This patch remove
hardware reset of MPEG encoder.
This is patch from our customer. I checked this.
With my best regards, Dmitry.
Signed-off-by: Alexey Osipov <lion-simba@pridelands.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Dmitri Belimov <d.belimov@gmail.com>
Hi All.
If video has a lot of changes in frame, MPEG encoder need more time for coding process.
Add new bigger timeout for encoder.
This is patch from our customer. I checked this.
Signed-off-by: Alexey Osipov <lion-simba@pridelands.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: hermann pitton <hermann-pitton@arcor.de>
The Compro VideoMate T750 has no support for IR and DVB-T yet.
Disable both to avoid fall through and confusing printouts.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Magnus Damm <damm@igel.co.jp>
Remove the videobuf-dma-contig sync operation. Sync is only needed
for noncoherent buffers, and since videobuf-dma-contig is built on
coherent memory allocators the memory is by definition always in sync.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Tobias Klauser <tklauser@distanz.ch>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
[mchehab@redhat.com: Fix a trivial merge conflict]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
CC: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@linuxtv.org>
A regression was introduced in hg changeset 33810c734a0d, which resulted in
a kernel panic whenever the device was disconnected from USB. The call to
4l2_device_register() was overwriting the pointer for usb_set_intfdata(), so
when au0828_usb_disconnect() was called, the usb_get_intfdata() returned a
pointer to the v4l2_device instead of the au0828_dev structure.
Priority: high
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
|
|
From: Christopher Pascoe <linuxdvb@itee.uq.edu.au>
Two fixes for DViCO FusionHDTV DVB-T Dual Express:
* Reset correct tuner when reinitializing xc3028.
* Disable the I2C gate control to avoid locking up the I2C bus.
Priority: high
Signed-off-by: Christopher Pascoe <linuxdvb@itee.uq.edu.au>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Tested-by: John Knops <jknops@australiaonline.net.au>
Reviewed-By: Steven Toth <stoth@linuxtv.org>
|
|
From: Andy Walls <awalls@radix.net>
Toggle the AI1 mux when changing the CX18_AUDIO_ENABLE register. It's hard to
reliably tell when we have written to this register successfully unless we
change some bits we know we can read back. The AI mux bits always read back
what we wrote to them, so force them to toggle whenever we have to write to
the register, so we can tell we wrote to the register successfully.
This change was prompted by users experiencing broadcast audio decoding
problems after the cx18 module loads for the first time.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Add code to verify the cx18-av-core digitizer firmware loads correctly. The
verification function reads back and compares the firmware bytes loaded
into the A/V core. The result of the verification is only used to log a
message in the system log.
This change was prompted by users with multiple card setups that have problems
with broadcast audio decoding the first time the cx18 module is loaded.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Both the MPEG-2 SVCD stream format and the MPEG-2 DVD stream format should
use an MPEG-2 PS container. This makes it safe to stuff IVTV Private Stream 1
VBI packets in these stream types using the existing cx18 driver routines.
Reported-by: Helen Buus <mythtv@hbuus.com>
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
modpost needs a __refdata marker in driver structs to ensure references to
.probe and .remove functions from .devinit.text and .devexit.text sections
respectively are valid. Add __refdata to soc_camera_pdrv platform driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jani Monoses <jani@ubuntu.com>
Priority: normal
Signed-off-by: Jani Monoses <jani@ubuntu.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Andy Walls <awalls@radix.net>
Ensure the variable gain amplifier gain for SIF is driven by the audio deocder
and not the video decoder. This forced rework of the analog front end (AFE)
configuration to not rely on autoconfiguration, but instead set up the AFE mux,
AFE parameters, and ADC1 & ADC2 configurations explicitly.
Reported-by: Helen Buus <mythtv@hbuus.com>
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
The number of packets per isochronous message may now be set by the subdrivers
(default value 32).
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
priority: high
---
drivers/media/video/mx3_camera.c | 4 ----
1 files changed, 0 insertions(+), 4 deletions(-)
|
|
From: Guennadi Liakhovetski <lyakh@axis700.grange>
With the transition of soc-camera to become a platform driver and to the
v4l2-subdev framework the initialisation order becomes important. In case
of a static build clients (i2c) drivers have to be available when host
drivers are probed. Moving host drivers down in the Makefile achieves the
desired order.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/Makefile | 9 +++++----
1 files changed, 5 insertions(+), 4 deletions(-)
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Register access routines only need the I2C client, not the soc-camera device
context.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/mt9m001.c | 105 +++++++++++++++++---------------
drivers/media/video/mt9m111.c | 73 ++++++++++++----------
drivers/media/video/mt9t031.c | 135 +++++++++++++++++++++-------------------
drivers/media/video/mt9v022.c | 135 +++++++++++++++++++++--------------------
4 files changed, 236 insertions(+), 212 deletions(-)
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Make camera devices direct children of host platform devices, move the
inheritance management into the soc_camera.c core driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/mx1_camera.c | 35 +++++-----
drivers/media/video/mx3_camera.c | 40 ++++++------
drivers/media/video/pxa_camera.c | 97 ++++++++++++++--------------
drivers/media/video/sh_mobile_ceu_camera.c | 21 +++---
drivers/media/video/soc_camera.c | 35 +++-------
include/media/soc_camera.h | 4 +-
6 files changed, 107 insertions(+), 125 deletions(-)
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Embed struct soc_camera_host in platform-specific per host instance objects
instead of allocating them statically in drivers, use platform_[gs]et_drvdata
consistently, use resource_size().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/mx1_camera.c | 21 ++++++++-----------
drivers/media/video/mx3_camera.c | 2 +-
drivers/media/video/pxa_camera.c | 29 ++++++++++++---------------
drivers/media/video/sh_mobile_ceu_camera.c | 6 ++--
4 files changed, 26 insertions(+), 32 deletions(-)
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Currently pcm990 camera bus-width management functions request a GPIO and never
free it again. With this approach the GPIO extender driver cannot be unloaded
once camera drivers have been loaded, also unloading theb i2c-pxa bus driver
produces errors, because the GPIO extender driver cannot unregister properly.
Another problem is, that if camera drivers are once loaded before the GPIO
extender driver, the platform code marks the GPIO unavailable and only a reboot
helps to recover. Adding an explicit free_bus method and using it in mt9m001
and mt9v022 drivers fixes these problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Eric Miao <eric.miao@marvell.com>
---
arch/arm/mach-pxa/pcm990-baseboard.c | 23 ++++++++++++++++-------
drivers/media/video/mt9m001.c | 3 +++
drivers/media/video/mt9v022.c | 3 +++
include/media/soc_camera.h | 1 +
4 files changed, 23 insertions(+), 7 deletions(-)
|
|
From: Dean Anderson <dean@sensoray.com>
This patch does:
- remove unused structure items.
- define Response values;
- change Driver revision printk.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
The new mechanism does not use any temporary buffer.
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
A new image may start without any UVC EOF in the last packet of the
previous image.
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Dmitri Belimov <d.belimov@gmail.com>
Split Beholdr`s cards to correct models.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
