| Age | Commit message (Collapse) | Author |
|---|
|
From: Mike Isely <isely@pobox.com>
Priority: normal
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Mike Isely <isely@pobox.com>
Priority: high
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Devin Heitmueller <dheitmueller@linuxtv.org>
Setup the i2c clock speed to be definable on a per-board basis. This allows
us to explicitly set the clock speed to 30 KHz on the 950q, and also gets rid
of code which sets it on a basis of what chip the i2c master is talking to
at any given time (which could have caused issues because i2c slaves should
never receive commands at a clock higher than their supported clock speed).
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
|
|
From: Devin Heitmueller <dheitmueller@linuxtv.org>
Change the #define entries for the i2c registers to be more meaningful, and
document the valid values for the registers. Note that this changeset makes
*no* functional changes to the code.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
|
|
From: Marton Balint <cus@fazekas.hu>
This patch changes cx88_set_stereo to avoid resetting all of the audio
registers on stereo/mono change if the audio standard is A2, and set
only the AUD_CTL register. The benefit of this method is that it
eliminates the annoying clicking noise on setting the audio mode to
stereo or mono.
The driver had used the same method 1.5 years ago (and for FM radio it
still does), but a pretty big cleanup commit changed it to the
"complete audio reset" method, although the reason for this move was
not clear. (If somebody knows why it was necessary, please let me
know!)
The original commit: http://linuxtv.org/hg/v4l-dvb/rev/ffe313541d7d
Priority: normal
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Marton Balint <cus@fazekas.hu>
The sole purpose of the audio thread is to detect if stereo transmission is
available, and if it is, then switch to stereo mode (and switch back, if it's
no longer available). This manual autodetection is useful for some audio
standards (e.g. A2) where cx88_get_stereo CAN detect stereo sound, but the
cx2388x chip CANNOT auto-detect stereo sound.
However, for other audio standards, the cx2388x chip CAN auto-detect the stereo
sound, so the manual autodetection in the audio thread is not needed. In fact,
it can cause serious problems because for some of these audio standards,
cx88_get_stereo CANNOT detect the presence of stereo sound. Besides that, if
the hardware automatically detects stereo/mono sound, you cannot set
core->audiomode_current to the real current audio mode on channel change.
With this patch, the manual autodetection is only used if audiomode_current is
known after a channel change (because of the initial mono mode), and
hardware-based stereo autodetecion is not applicable for the current audio
standard.
Priority: normal
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Marton Balint <cus@fazekas.hu>
The patch implements reliable stereo and sap detection for the A2 sound
standard. This is achieved by processing the samples of the audio RDS fifo of
the cx2388x chip. A2M, EIAJ and BTSC stereo/sap detection is also possible with
this new approach, but it's not implemented yet. Stereo detection when alsa
handles the sound also does not work yet.
Priority: normal
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Alexey Klimov <klimov.linux@gmail.com>
Patch fixes cleanup procedure in si470x_usb_driver_probe. Add new label
err_video and change order of freeing memory.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Douglas Schilling Landgraf <dougsland@redhat.com>
Converted em28xx driver to v4l2_subdev.
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for helping this conversion.
Priority: normal
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Antti Palosaari <crope@iki.fi>
Add USB ID (07ca:850a) and configuration hack for AverMedia AVerTV Volar
Black HD (A850) DVB-T USB stick.
Priority: normal
Signed-off-by: Antti Palosaari <crope@iki.fi>
Tested-by: Olivier MENUEL <omenuel@laposte.net>
Tested-by: Thomas Renard <threnard@gmail.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/ov772x.c | 63 +++++++++++++++++++++++++++++++++++++++--
include/media/ov772x.h | 35 +++++++++++++++++++++++
2 files changed, 94 insertions(+), 4 deletions(-)
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
MT9M001 datasheet says, that the data is ready on the falling edge of the pixel
clock, but the driver wrongly sets the SOCAM_PCLK_SAMPLE_RISING flag. Changing
this doesn't seem to produce any visible difference, still, it is better to
comply to the datasheet.
Reported-by: Sascha Oppermann <oppermann@garage-computers.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/mt9m001.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
soc-camera re-uses struct devices multiple times in calls to device_register(),
therefore it has to reset the embedded struct kobject to avoid the "tried to
init an initialized object" error, which then also erases its name. Now with
the transition to kobject's name for device names, we have to re-initialise the
name before each call to device_register().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/soc_camera.c | 6 ++++--
1 files changed, 4 insertions(+), 2 deletions(-)
|
|
From: Kuninori Morimoto <morimoto.kuninori@renesas.com>
priv->client->dev.platrom_data mean ov772x_camera_info in ov772x driver.
So, struct soc_camera_link doesn't exist there.
This patch modify this bug.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/ov772x.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
|
|
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
pxa_dma_update_sg_tail() is called only once, runs exactly the same loop as the
caller and has to recalculate the last element in an sg-list, that the caller
has already calculated. Eliminate redundancy by merging the two loops and
re-using the calculated pointer. This also saves a bit of performance which is
always good during video-capture.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
---
drivers/media/video/pxa_camera.c | 20 ++++++--------------
1 files changed, 6 insertions(+), 14 deletions(-)
|
|
From: Robert Jarzmik <robert.jarzmik@free.fr>
The last buffer queued will often overrun, as the DMA chain
is finished, and the time the dma irq handler is activated,
the QCI fifos are filled by the sensor.
The fix is to ignore the overrun condition on the last
queued buffer, and restart the capture only on intermediate
buffers of the chain.
Moreover, a fix was added to the very unlikely condition
where in YUV422P mode, one channel overruns while another
completes at the very same time. The capture is restarted
after the overrun as before, but the other channel
completion is now ignored.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/pxa_camera.c | 25 ++++++++++++++++++++-----
1 files changed, 20 insertions(+), 5 deletions(-)
|
|
From: Robert Jarzmik <robert.jarzmik@free.fr>
The DMA transfers in pxa_camera showed some weaknesses in
multiple queued buffers context :
- poll/select problem
The bug shows up with capture_example tool from v4l2 hg
tree. The process just "stalls" on a "select timeout".
- multiple buffers DMA starting
When multiple buffers were queued, the DMA channels were
always started right away. This is not optimal, as a
special case appears when the first EOF was not yet
reached, and the DMA channels were prematurely started.
- Maintainability
DMA code was a bit obfuscated. Rationalize the code to be
easily maintainable by anyone.
- DMA hot chaining
DMA is not stopped anymore to queue a buffer, the buffer
is queued with DMA running. As a tribute, a corner case
exists where chaining happens while DMA finishes the
chain, and the capture is restarted to deal with the
missed link buffer.
This patch attemps to address these issues / improvements.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
Documentation/video4linux/pxa_camera.txt | 125 ++++++++++++
drivers/media/video/pxa_camera.c | 319 ++++++++++++++++++------------
2 files changed, 316 insertions(+), 128 deletions(-)
create mode 100644 Documentation/video4linux/pxa_camera.txt
|
|
From: Robert Jarzmik <robert.jarzmik@free.fr>
All planes were PAGE aligned (ie. 4096 bytes aligned). This
is not consistent with YUV422 format, which requires Y, U
and V planes glued together. The new implementation forces
the alignement on 8 bytes (DMA requirement), which is almost
always the case (granted by width x height being a multiple
of 8).
The test cases include tests in both YUV422 and RGB565 :
- a picture of size 111 x 111 (cross RAM pages example)
- a picture of size 1023 x 4 in (under 1 RAM page)
- a picture of size 1024 x 4 in (exactly 1 RAM page)
- a picture of size 1025 x 4 in (over 1 RAM page)
- a picture of size 1280 x 1024 (many RAM pages)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/pxa_camera.c | 145 +++++++++++++++++++++++++++----------
1 files changed, 106 insertions(+), 39 deletions(-)
|
|
From: Robert Jarzmik <robert.jarzmik@free.fr>
Due to DMA constraints, the DMA chain always transfers bytes
from the QCI fifos to memory in 8 bytes units. In planar
formats, that could mean 0 padding between Y and U plane
(and between U and V plane), which is against YUV422P
standard.
Therefore, a frame size is required to be a multiple of 16
(so U plane size is a multiple of 8). It is enforced in
try_fmt() and set_fmt() primitives, be aligning height then
width on 4 multiples as need be, to reach a 16 multiple.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
drivers/media/video/pxa_camera.c | 32 +++++++++++++++++++++-----------
1 files changed, 21 insertions(+), 11 deletions(-)
|
|
From: Kyle McMartin <kyle@mcmartin.ca>
CUSTOMISE appears to be the one actually defined...
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Antti Palosaari <crope@iki.fi>
Remove wrong GPIO definitions. GPIOs used by AF9015 are property of the
AF9013 demodulator and are coming from there.
Priority: normal
Signed-off-by: Antti Palosaari <crope@iki.fi>
|
|
From: Dean Anderson <dean@sensoray.com>
This patch fixes kfree problem on driver removal, fixes streamoff problem
and removes unnecessary videobuf_waiton from free_buffer function.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The tuner ops pointer wasn't set, so s_std never worked here.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
I2C_DRIVERIDs are no longer needed with v4l2_subdev and will be removed
from the kernel soon.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CC: Devin Heitmueller <dheitmueller@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Alexey Klimov <klimov.linux@gmail.com>
Patch removes empty open and release functions in pci and isa radio
drivers, setting them to NULL. V4L module doesn't call for them due to
previous patch.
Priority: normal
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Patch allows v4l2_open and v4l2_release functions return 0 if open and
release driver callbacks set to NULL. This will be used in radio
drivers.
--
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
No i2c modules are called with the V4L1 API anymore, so this can be removed.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Replace 'VIDIOC_' references in v4l i2c drivers by their new v4l2_subdev
callback names.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The audio and vbi parts still used an 'ioctl'-like interface. Replace this
with normal functions.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CC: Andy Walls <awalls@radix.net>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The audio and vbi functions where still called through an ioctl-like
interface, even though this is no longer needed with v4l2-subdev. Just
change each 'case' into a proper function and call that directly.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Adam Baker <linux@baker-net.org.uk>
Add support to the SQ-905 driver to pass back to user space the
sensor orientation information obtained from the camera during init.
Modifies gspca and the videodev2.h header to create the necessary
API.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
[mchehab@redhat.com: Changed "Output is" to "Frames are" at the comments, as suggested at LMML]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
tuner-core.c contains a hack for cx88 board to prevent probing of certain
addresses:
/* HACK: Ignore 0x6b and 0x6f on cx88 boards.
* FusionHDTV5 RT Gold has an ir receiver at 0x6b
* and an RTC at 0x6f which can get corrupted if probed.
*/
With the new i2c API this hack no longer works. So instead change the
list of tuner probe addresses in the cx88 driver itself, which is much
more clean.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Matthias Schwarzott <zzam@gentoo.org>
Thanks to panagonov <panagonov@mail.bg> for requesting support and
testing patches.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Add support for CMOS Sensor Interface on i.MX1 and i.MXL SoCs.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
arch/arm/mach-mx1/Makefile | 5 +-
arch/arm/mach-mx1/devices.c | 2 +-
arch/arm/mach-mx1/ksym_mx1.c | 18 +
arch/arm/mach-mx1/mx1_camera_fiq.S | 35 ++
arch/arm/plat-mxc/include/mach/memory.h | 8 +
arch/arm/plat-mxc/include/mach/mx1_camera.h | 35 ++
drivers/media/video/Kconfig | 13 +-
drivers/media/video/Makefile | 1 +
drivers/media/video/mx1_camera.c | 827 +++++++++++++++++++++++++++
9 files changed, 941 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/mach-mx1/ksym_mx1.c
create mode 100644 arch/arm/mach-mx1/mx1_camera_fiq.S
create mode 100644 arch/arm/plat-mxc/include/mach/mx1_camera.h
create mode 100644 drivers/media/video/mx1_camera.c
|
|
From: Guennadi Liakhovetski <lg@denx.de>
With the i.MX31 transition to clkdev clock names have changed, but mistakenly
the "mx3-camera.0" has been registered with a non-NULL connection ID, which is
not necessary, since this is the only clock, used by the capture interface
driver. Fix the clock definition and the driver to use NULL as a connection ID.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/arm/mach-mx3/clock.c | 2 +-
drivers/media/video/mx3_camera.c | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
|
|
From: Guennadi Liakhovetski <lg@denx.de>
Use platform power hook to turn the camera on and off.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
---
drivers/media/video/mt9t031.c | 21 +++++++++++++++++++++
1 files changed, 21 insertions(+), 0 deletions(-)
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Remove support for the debug call VIDIOC_INT_S_AUDIO_ROUTING from cx18
and ivtv. These internal ioctls shouldn't be exposed. These were only
used through the cx18-ctl and ivtv-ctl utilities, and only when testing
a new card variant.
This cleanup allows the removal of this ioctl from v4l2-common.h.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CC: Andy Walls <awalls@radix.net>
|
