| Age | Commit message (Collapse) | Author |
|---|
|
From: Jarod Wilson <jwilson@redhat.com>
This patch causes the bttv driver to automatically load the dvb-bt8xx module
for bttv/dvb hybrid cards. Successfully tested with a pcHDTV HD-2000 card.
This patch is based on the recent patches to enable autoloading of cx88-dvb,
cx88-blackbird and saa7134-dvb.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Adrian Bunk <bunk@stusta.de>
After looking at a section bug (in the non-modular case, clearly
non-init code referenced the __initdata parport_nr[]), I thought it was
time to convert this driver to module_{init,exit}.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Jonathan Corbet <corbet@lwn.net>
Add raw bayer support to the ov7670 driver
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Jonathan Corbet <corbet@lwn.net>
Don't mirror ov7670 images by default
The ov7670 sensor driver sets the mirror bit by default, which is not
the desired mode. OLPC has been running with this patch for a while.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Jonathan Corbet <corbet@lwn.net>
Add suspend/resume support to the Cafe CCIC driver.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Jonathan Corbet <corbet@lwn.net>
Fix up unsociable Cafe CCIC delays
The Cafe CCIC driver contains some lengthy delays, some of which are
unnecessary and some of which are done under lock. Some were marked
with comments, but the comments somehow failed to make the issue go
away. So fix it for real.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Jonathan Corbet <corbet@lwn.net>
Remove an obsolete PCI ID
The CAFE driver includes three PCI IDs, one of which corresponds to
a development board which is no longer in use.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Jonathan Corbet <corbet@lwn.net>
Set the PCI dev in the V4L2 dev so that the proper sysfs link gets made
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes a few troubles on nxt200x implementation:
1) A nxt200x internal input control logic were done on both
cx88-dvb and saa7134-dvb;
2) The nx200x_set_pll_input callback were filling buffer, at the
5th position, without even testing if that buffer were filled;
3) a 5 byte buffer were written to the device, even if the
buffer were not properly initialized by calc_regs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Thomas Viehweger <Thomas.Viehweger@marconi.com>
After freeing a block there should be no reference to this block.
Signed-off-by: Thomas Viehweger <Thomas.Viehweger@marconi.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Logitech ViewPort AV 100 has the same internals as Cisco VT Camera.
Fixing Pwc driver to handle it properly.
Also, fixed the comments for both cameras.
Thanks to Martin Rubli for pointing me this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Jean Tourrilhes <jt@hpl.hp.com>
I have a Cisco VT Camera, and it was just collecting dust. I decided to
try connecting it to my Linux box at home.
Just a disgression about the product. The Cisco VT Camera is a webcam
Cisco sold to work with their IP phone hardware and software. It's mostly
useless on Windows, as it interfaces only to Cisco software. You can find
some for cheap on eBay...
Physically, it's just a Logitech Pro 4000. The only difference with the
Pro 4000 is the Cisco logo and that it's grey like the Pro 3000. I believe
Cisco is now selling the Cisco VT Camera II, which look to be something
else...
So, assuming that it was a Pro 4000 inside, I created the little patch
attached.
I'm new to webcam under Linux, but I managed to get an image from it using
xawtv, and the image looked all right, so I consider that a success. The
imaged seemed a bit small and I could not get the microphone driver loaded,
but I assume it's my lack of experience. Note that I did not try any other
type_id, but this one works great.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The dvb-pll sleep function could only send a 2-byte sequence to the PLL.
This isn't enough in some cases, for example fmd1216me will need to send
a 4-byte command to set both BB and AB to the correct values.
Instead of using a fake band with a frequency of 0 to store the sleep
data (which has room for only two bytes), the new sleep function works
like the init function. A new pointer is added to the pll description,
and when non-NULL points to a buffer with the length and data to send.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
The IF frequency was specified for each band, but it's not something that
changes from band to band. None of the tuner definitions had a different
IF frequency (called offset) from one band to another.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
Some PLLs had one half the step size added to the offset, so that the
divisor would be rounded to the nearest integer. Some didn't and so
would always be rounded down.
This makes dvb-pll round to the nearest when calculating the divisor,
without the offset needing to be fudged. PLLs that had a fudged offset
have the offset changed to be just the IF frequency.
The satellite PLL dvb_pll_philips_sd1878_tda8261 was rounding up for some
reason, and I've kept it that way.
In addition, frequencies that were rounded to the nearest kHz are
extended to full Hz resolution. One sixth MHz step sizes that were
listed as 166,666 Hz are changed to 166,667 Hz, which is slightly closer.
PLLs that were already rounding:
dvb_pll_tda665x, offset was 36 1/6 (to nearest kHz) + step/2
dvb_pll_fmd1216me, offset was 36 1/8 (to two digits) + step/2
dvb_pll_thomson_fe6600, offset was 36 1/8 (to two digits) + step/2
dvb_pll_env57h1xd5, offset was 36 1/8 + step
Note that the last PLL, dvb_pll_env57h1xd5, appears to have had a bug in
the offset. Rather than adding stepsize/2, it was adding a full
stepsize. The PLL definition originally came from the dibusb driver,
which used 36 1/8 + step/2. The change to 36 1/8 + step was probably a
mistake added when the tuner was converted to dvb-pll.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Pierre Willenbrock <pierre@pirsoft.de>
Add support for Anubis Electronics "Lifeview" (USB-ID: 0x10fd:0x1513)
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
The struct tda1004x_config has a new entry: .ts_mode
Possible values are TDA10046_TS_PARALLEL or TDA10046_TS_SERIAL
There always is only one interface active, default is parallel.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Ian Armstrong <ian@iarmst.demon.co.uk>
Modifies automatic mode selection for yuv playback. Behaviour is now that
source video with a vertical resolution below that of the currently set
broadcast mode will be treated as progressive. Video with a vertical
resolution greater or equal to the current broadcast mode (up to 576 lines)
will be treated as interlaced.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Pierre Willenbrock <pierre@pirsoft.dnsalias.org>
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.dnsalias.org>
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Aapo Tahkola <aet@rasterburn.org>
This function should work for all m920x-based devices.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
The new name fits to what it is and what is on the box.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
There are 2 new entries for p7131 boards and one correction for a board
with LNA
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Static locals should not be changed - the original contents gets lost.
Thanks to Trent Piepho for pointing me to this.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Besides power saving, this puts the AGC output of the tda8290
to tristate. This is necessary for some hybrid boards which
don't use a multiplexer for the AGC
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Steven Toth <stoth@hauppauge.com>
Some of the new tuner entries may need to be mapped to compatible
tuners already defined. I don't know for certain which tuners
are compatible between manufacturers.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
|
|
From: Oliver Endriss <o.endriss@gmx.de>
Fix bug introduced during infrared refactoring.
Thanks to Johann Friedrichs for spotting this.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Thanks-to: Johann Friedrichs <johann.friedrichs@web.de>
|
|
From: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Change a 00 to just 0
Detect zero-length I2C messages and return not supported. I think I know
how to send one, but the problem is getting the slave's ack. The only
point of a zero-length message is for probing; too see if the slave will
ack its address. Since we don't know how to get the ack, we can't
support zero-length messages in a useful way, so it's probably best to
just return not supported for them.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Once the devices have been registered anyone can start changing the inputs or
TV standard before they have been initialized by the driver. This leads to
cases were the input is changed in an udev rule, but after that rule is
triggered the tail-end of the ivtv driver initialization can override
that by selecting the tuner input.
The correct sequence is to first setup the input, initial frequency and TV
standard before finally registering the video devices. This prevents any
udev rules from being triggered prematurely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
replace leading spaces with tabs
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
The ADS Tech InstantTV DVB-S is a clone of the KWorld DVB-S 100.
This patch adds autodetection support for this card based on
pci subsystem id.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
ivtv_remove which is called by pci_unregister_driver was still using
memory that was already freed. Ouch.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Returning -1 causes the probe to stop, but it should just continue
instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
VIDIOC_TRY_ENCODER_CMD did the same as VIDIOC_ENCODER_CMD, now it no longer
touches the encoder.
Both the encoder and decoder commands did not clear the flags field of unknown
flags.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
