| Age | Commit message (Collapse) | Author |
|---|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Register 0x13 seems to be a sort of image control, maybe gamma. Lower
values produce better images, while higher values increases the contrast
and shifts colors to green. 0xff produces a black image.
If this register is left alone, a random value can be found at the
register, producing weird results.
This register doesn't seem to affect tv streams.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Silvercrest mt9v011 sensor produces a 640x480 image. However,
previously, the code were getting only half of the lines and merging two
consecutive frames to "produce" a 640x480 image.
With the addition of progressive mode, now em28xx is working with a full
image. However, when the number of lines is bigger than 240, the
beginning of some odd lines are filled with blank.
After lots of testing, and physically checking the device for a Xtal, it
was noticed experimentally that mt9v011 is using em28xx XCLK as its
clock. Due to that, changing XCLK value changes the maximum speed of the
stream.
At the tests, it were possible to produce up to 32 fps, using a 30 MHz
XCLK. However, at that rate, the artifacts happen even at 320x240. Lower
values of XCLK produces artifacts only at 640x480.
At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is
possible to see an invalid sucession of artifacts with this pattern:
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
(where the dots represent the blanked pixels)
So, it seems that a waveform in the format of a ramp is interferring at
the image.
The cause of this interference is currently unknown. Some possibilities
are:
- electrical interference (maybe this device is broken?);
- some issue at mt9v011 programming;
- some bug at em28xx chip.
So, for now, let's be conservative and use a value of XCLK that we know
for sure that it won't cause artifacts.
As I'm waiting for more of such devices with different em28xx chipset
revisions, I'll have the opportunity to double check the issue with
other pieces of hardware.
Later patches can vary XCLK depending on the vertical resolutions, if a
proper fix is not discovered.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.
Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch supports i2c interface of si470x. The i2c specific part
exists in radio-si470x-i2c.c file and the common part uses
radio-si470x-common.c file. The '#if defined' is inserted inevitably
because of parts used only si470x usb in the common file.
The current driver version doesn't support the RDS.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
---
linux/drivers/media/radio/si470x/Kconfig | 13 +
linux/drivers/media/radio/si470x/Makefile | 2 +
.../media/radio/si470x/radio-si470x-common.c | 6 +
.../drivers/media/radio/si470x/radio-si470x-i2c.c | 254 ++++++++++++++++++++
linux/drivers/media/radio/si470x/radio-si470x.h | 6 +
5 files changed, 281 insertions(+), 0 deletions(-)
create mode 100644 linux/drivers/media/radio/si470x/radio-si470x-i2c.c
|
|
The si470x_disconnect_check is function to check disconnect state of
radio in common file. The function is implemented in each interface
file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
---
.../media/radio/si470x/radio-si470x-common.c | 40 +++++++++----------
.../drivers/media/radio/si470x/radio-si470x-usb.c | 17 ++++++++
linux/drivers/media/radio/si470x/radio-si470x.h | 1 +
3 files changed, 37 insertions(+), 21 deletions(-)
|
|
This patch is for using dev_* macro instead of printk.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
---
.../media/radio/si470x/radio-si470x-common.c | 50 +++++++++---------
.../drivers/media/radio/si470x/radio-si470x-usb.c | 58 +++++++++-----------
2 files changed, 52 insertions(+), 56 deletions(-)
|
|
This patch is a preceding work to add the i2c interface of si470x.
The si470x directory includes a common file and usb specific file and
header file.
The part unrelated with usb interface and i2c interface exists in
radio-si470x-common.c file, and The usb specific part exists in
radio-si470x-usb.c file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Small changes, due to new include "linux/smp_lock.h".
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
---
linux/drivers/media/radio/Kconfig | 26 +-
linux/drivers/media/radio/Makefile | 2 +-
linux/drivers/media/radio/radio-si470x.c | 1870 --------------------
linux/drivers/media/radio/si470x/Kconfig | 24 +
linux/drivers/media/radio/si470x/Makefile | 7 +
.../media/radio/si470x/radio-si470x-common.c | 794 +++++++++
.../drivers/media/radio/si470x/radio-si470x-usb.c | 958 ++++++++++
linux/drivers/media/radio/si470x/radio-si470x.h | 202 +++
8 files changed, 1989 insertions(+), 1892 deletions(-)
delete mode 100644 linux/drivers/media/radio/radio-si470x.c
create mode 100644 linux/drivers/media/radio/si470x/Kconfig
create mode 100644 linux/drivers/media/radio/si470x/Makefile
create mode 100644 linux/drivers/media/radio/si470x/radio-si470x-common.c
create mode 100644 linux/drivers/media/radio/si470x/radio-si470x-usb.c
create mode 100644 linux/drivers/media/radio/si470x/radio-si470x.h
|
|
without it
From: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API (chapter 1.5) states that:
Drivers must implement all input ioctls when the device has one
or more inputs, all output ioctls when the device has one or more outputs.
When the device has any audio inputs or outputs the driver must set the
V4L2_CAP_AUDIO flag in the struct v4l2_capability returned by the
VIDIOC_QUERYCAP ioctl.
So, devices without audio input should return -EINVAL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@linuxtv.org>
Add support for the remote control that comes with the Cinergy Hybrid T USB XS
Thanks to Jelle de Jong for providing sample hardware to test with.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Cc: Jelle de Jong <jelledejong@powercraft.nl>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced. The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured. Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.
Thanks to user "ritec" for reporting the issue and testing the fix.
Priority: high
Cc: rictec <rictec@netcabo.pt>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
The introduction of the zl10353 i2c gate control broke support for the
Geniatech board (which is not behind an i2 gate). Add the needed parameter.
Priority: high
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
Priority: high
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
Priority: high
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
|
|
From: Theodore Kilgore <kilgota@auburn.edu>
Priority: normal
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Eberhard Mattes <eberhard.mattes@web.de>
cinergyInitialize param.flags.
Priority: normal
Signed-off-by: Eberhard Mattes <eberhard.mattes@web.de>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
Remove the following build warning:
sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'
Thanks to Hans Verkuil for pointing this out.
The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.
Priority: high
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Laurent Pinchart <laurent.pinchart@skynet.be>
The iSight sends non-UVC status events through the interrupt endpoint. Those
invalid events are reported to the kernel log, resulting in a log flood.
Only log the events when the UVC_TRACE_STATUS flag is set.
Priority: high
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jiri Slaby <jirislaby@gmail.com>
There are many lock imbalances in this driver. Fix all found.
Priority: normal
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Marton Nemeth <nm127@freemail.hu>
The vidioc_s_std() is not necessary when vdev->tvnorms == 0.
Priority: normal
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jiri Slaby <jirislaby@gmail.com>
There seems to be one superfluos unlock in a poll function. Remove it.
Priority: normal
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Nils Kassube <kassube@gmx.net>
Moving BOOT fixes problem.
Priority: normal
Signed-off-by: Nils Kassube <kassube@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Oliver Neukum <oliver@neukum.org>
The irq handler will touch memory. Even in the error case some URBs may
complete. Thus no memory must be kfreed before all URBs are killed.
Priority: normal
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Andy Walls <awalls@radix.net>
This patch adds support for Zilog Z8F0811 IR transceiver chips on
CX2341[68] based boards to ir-kbd-i2c for both the old i2c binding model
and the new i2c binding model.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Andy Walls <awalls@radix.net>
This patch add support to the cx18 driver for setting up the
Z8F0811/Hauppauge IR Tx/Rx chip with the i2c binding model in newer
kernels.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Andy Walls <awalls@radix.net>
This patch augments the init data passed by bridge drivers to
ir-kbd-i2c, so that the ir_type can be set explicitly, and so
ir-kbd-i2c internal get_key functions can be reused without
requiring symbols from ir-kbd-i2c in the bridge driver.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean Delvare <khali@linux-fr.org>
Functions which are referenced by their address can't be inlined by
definition.
Priority: normal
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Douglas Schilling Landgraf <dougsland@redhat.com>
Fixed checkpath warnings
Priority: normal
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Even devices without ac97 needs to call analog audio setup function, to
properly set xclk and mute/unmute.
Thanks to Angelo Cano <acano@fastmail.fm> for reporting and testing it.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.
Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.
Priority: normal
Tested-by: Angelo Cano <acano@fastmail.fm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
This prevents a loop if a permanent error occurs in usb_set_interface().
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Hans de Goede <hdegoede@redhat.com>
Priority: normal
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Denis Loginov <dinvlad@gmail.com>
Priority: normal
Signed-off-by: Denis Loginov <dinvlad@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Michael Krufky <mkrufky@kernellabs.com>
The au0828-dvb driver uses bulk usb transfers for digital transport,
but the debug reports, "iso xfer already running!\n".
Fix this to report bulk instead of isoc.
Priority: normal
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Also, H/V flip default values adjusted according to the webcam IDs.
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Jean-Francois Moine <moinejf@free.fr>
Priority: normal
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: AceLan Kao <acelan.kao@canonical.com>
The patches
gspca - vc032x: Add resolution 1280x1024 for sensor mi1310_soc.
gspca - vc032x: Webcam 041e:405b added and mi1310_soc updated.
will make the preview function not work, so I disable the 1280x1024 resolution
and revert back to the origin mi1310_soc settings.
And, using USB snoop tool on Windows to get the correct i2c commands to
turn on/off the LED flash.
Priority: normal
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
|
|
From: Sohail Syyed <linuxtv@hubstar.net>
Current tip is broken and does not switch back to DVB-T correctly
Priority: high
Signed-off-by: Sohail Syyed <linuxtv@hubstar.net>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
