| Age | Commit message (Collapse) | Author |
|---|
|
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
All drivers should provide a spinlock to be used in videobuf operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Reviewed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Function pointers and the driver owner are not expected to change
throughout soc-camera host's life. Extract them into an operations struct.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
In case of muliple cameras, handled by the same driver, they can support
different picture formats, therefore formats and num_formats cannot belong
to soc_camera_ops, which is only one per driver, move them to
soc_camera_device, which is one per device instance. OTOH, probe and
remove methods are always the same, move them to soc_camera_ops.
Thanks to Eric Miao for making me look at this code again:-)
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Improve hardware parameter negotiation between the camera host driver and
camera drivers. Parameters like horizontal and vertical synchronisation,
pixel clock polarity shall be set depending on capabilities of the
parties.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Only attach cameras to the host interface for probing, then detach until
open. This allows platforms with several cameras on an interface,
physically supporting only one camera, to handle multiple cameras and
activate them selectively after initial probing. The first attach during
probe is needed to activate the host interface to be able to physically
communicate with cameras.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
This driver provides an interface between platform-specific camera
busses and camera devices. It should be used if the camera is connected
not over a "proper" bus like PCI or USB, but over a special bus, like,
for example, the Quick Capture interface on PXA270 SoCs. Later it should
also be used for i.MX31 SoCs from Freescale. It can handle multiple
cameras and / or multiple busses, which can be used, e.g., in
stereo-vision applications.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
