- Fixed 'Transfer Mode' in cases where a non-primary interface was switched to
  a channel that only the primary interface can receive (which could happen in
  the EPG scanner).
- The EPG scanner now starts with the first channel (it used to start with the
  second channel).
- Reacitvated setting the PNR.
- Adapted the frame scanning to the new muxing of the driver.
- The new compile time option REMOTE=NONE can be used to compile VDR without
  any remote control support (for applications where it shall be controlled
  exclusively via SVDRP).
- The new command line option -D can be used to define which DVB interfaces
  a certain instance of VDR shall use.
- The "Left" and "Right" keys are now used to page up and down in lists (thanks
  to Martin Hammerschmid). Since the "Timers" menu already uses these keys to
  (de)activate timers, this functionality is not available there.
- The "Main" and "Commands" menu now support "hotkeys", which means that if the
  first non-blank character of a menu item is a digit in the range 1..9, that
  item can be selected by pressing the respective numeric key on the remote
  control.
- The channel data in 'channels.conf' now contains the teletext PID (thanks to
  Dave Chapman). Existing files will be read normally (and the teletext PID set
  to 0), but once they are written back (due to some channel editing) the file
  will have the new format.
- The EPG scanner now scans each transponder only once per cycle.
- Deleted recordings are now automatically removed from disk after a while (not
  only when disk space is being needed for a new recording).
- Fixed repeat function in LIRC remote control.
- Changed the MAXDVBAPI macro in dvbapi.c to 4 in order to directly support the
  maximum possible number of DVB cards.
- The 'Ca' parameter in the default 'channels.conf' has been changed from '2'
  to '3' because the VDR prototype now has 3 DVB cards (and currently the CAM
  module only works if it is inserted into the last DVB card).
- The "Now", "Next" and "Schedule" menus now remember the current channel and
  restore the list when switching between them.
- The "Green" button in the "Recordings" menu can now be used to rewind a
  recording and play it from the very beginning.
- Fixed handling ':' in timer filenames and '\n' in timer summaries (see FORMATS).
- When removing recordings empty directories are now removed from the video
  directory.
- Added the "schnitt" tools from Matthias Schniedermeyer.
- New SVDRP command MESG to display a short message on the OSD.
- The Perl script 'svdrpsend.pl' can be used to send SVDRP commands to VDR.
- SVDRP can now immediately reuse the same port if VDR is restarted.
- SVDRP now has a timeout after which the connection is automatically closed
  (default is 300 seconds, can be changed in "Setup").
- The compile time switch VFAT can be used to make VDR avoid the ':' character
  in file names (VFAT can't handle them). Do 'make VFAT=1' to enable this.
- Support for DVB-C (thanks to Hans-Peter Raschke and Peter Hofmann).
  See the INSTALL file for more information about the use of VDR with cable.
- Fixed an occasional segfault in the EIT processor.
- A value of '0' for the EPGScanTimeout setup parameter now completely turns off
  scanning for EPG data on both single and multiple card systems.
- New setup parameter "PrimaryLimit" that allows to prevent timers from using the
  primary DVB interface in multi card systems. Default value is 0, which means
  that every timer may use the primary interface.
- The 'active' field of a timer will now be explicitly set to '1' if the user
  modifies an active timer (see FORMATS for details).
- The new command line option -w can be used to activate a watchdog that makes
  VDR exit in case the main program loop does not respond for more than the
  given number of seconds. This is mainly useful in combination with the new
  'runvdr' script that restarts VDR in case is has exited.

- Date and time in the title of an event info page are now always right adjusted.
- The 'current channel' is now handled device specific (in case there is more
  than one DVB card).
- The 'SetSystemTime' option in the "Setup" menu is now shown as "yes/no".
- Implemented "internationalization" (see 'i18n.c' for information on how to
  add new languages). Thanks to Miha Setina for translating the OSD texts to
  the Slovenian language.
- Fixed learning keys on the PC keyboard (display oscillated).
- Fixed a timing problem with OSD refresh and SVDRP.
- Avoiding multiple definitions of the same timer in the "Schedule" menu (this
  could happen when pressing the "Red" button while editing the timer).
- There can now be a configuration file named 'commands.conf' that defines
  commands that can be executed through the "Main" menu's "Commands" option
  (see FORMATS for details on how to define these commands).
- Added a 'fixed' font for use with the output of system commands.
- The 'Priority' parameter of the timers is now also used to interrupt a low
  priority timer recording if a higher priority timer wants to record.
- A timer recording on a DVB card with a CAM module will now be interrupted
  by a timer that needs to use this specific DVB card to record an encrypted
  channel, if the timer currently occupying this DVB card doesn't need the
  CAM module (and thus can continue recording on a different DVB card).
- The "Yellow" button in the "What's on now/next?" menus now displays the
  schedule of the current channel from that menu.
- All DVB cards in a multi-card system now write their EIT information into the
  same data structure.
- If there is more than one DVB card in the system, the non-primary cards are
  now used to periodically scan through the channels in order to keep the
  EPG info up-to-date. Scanning kicks in after 60 seconds of user inactivity
  (timeout in order to keep user interactions instantaneously) and each channel
  that has the 'pnr' parameter defined in 'channels.conf' is switched to for
  20 seconds. If there is only one DVB card in the system, that card will start
  scanning after 5 hours (configurable through the "Setup" menu) of user inactivity
  and will switch back to the channel it originally displayed at the first sign of
  user activity. Any scanning will only occur if that particular card is not
  currently recording or replaying.
- Now shifting the 'Subtitle' info into the 'ExtendedDescription' on stations
  that don't send the EIT information correctly (like, e.g., 'VOX').
- Implemented a 10 seconds latency when removing files.
- Fixed unwanted reaction on the "Green" and "Yellow" button in the "Event" display.
- Implemented 'Transfer Mode' to display video data from the DVB card that actually
  can receive a certain channel on the primary interface. This is currently in
  an early state and may still cause some problems, but it appears to work nice
  already.

- The EIT information is now gathered in a separate thread.
- The sytem time can now be synchronized to the time broadcast in the DVB data
  stream. This can be enabled in the "Setup" menu by setting "SetSystemTime" to
  1.  Note that this works only if VDR is running under a user id that has
  permisson to set the system time.
- The new item "Schedule" in the "Main" menu opens VDR's EPG (thanks to Robert
  Schneider). See the MANUAL file for a detailed description.
- The new setup parameters MarginStart and MarginStop define how long (in
  minutes) before the official start time of a broadcast VDR shall begin
  recording, and how long after the official end time it shall stop recording.
  These are used when a recording is programmed from the "Schedules" menu.
- The delay value in the dvb.c.071.diff patch to the driver has been increased
  to '3', because on some systems the OSD was not displayed correctly. If you
  are running an already patched version 0.71 driver and encounter problems
  with the OSD, please make sure the parameter in the ddelay call is '3', not
  '2'.
- Fixed initializing the RCU remote control code (didn't work after switching
  on the system).
- Problematic characters in recording names (which can come from timers that
  are programmed via the "Schedules" menu) are now replaced by suitable
  substitutes.

- Added support for LIRC remote control (thanks to Carsten Koch!).
  There are now three different remote control modes: KBD (PC-Keyboard), RCU
  and LIRC. See the INSTALL file for information on how to enable either of
  these modes. The default mode is now KBD, not RCU as before (to make it
  work immediately even if there is no actual remote control).
- Fixed small bug in dvbapi.c that was causing some channels (many on hotbird)
  not to be correctly tuned (thanks to Plamen Ganev!).
- Now clearing the replay buffer in search forward/back, which results in
  faster reaction.
- The 'Recordings' menu is now listed alphabetically (thanks to Carsten Koch!).
- The new 'epg2timers' tool (thanks to Carsten Koch!) can be used to convert
  an EPG "merkliste" page (http://www.tvtv.de) to vdr timer entries.
- The new 'xtvrc2vdr' tool (thanks to Plamen Ganev!) can be used to convert
  'xtvrc' channel files into 'vdr' format.
- When more than one timer matches at the same time, the first one in the list
  with the highest 'Priority' is selected.
- The MANUAL section on "Programming the Timer" has been filled in.
- The year in the "Recordings" menu as well as in the progress display during
  replay has been reduced to 2 digits to allow more space for the recording's
  title. In the internal file structure the year is still stored with 4 digits,
  so there will be no problem at the next turn of the century ;-)
- Channel names and timer filenames can now contain blanks. To avoid problems
  with file names that contain blanks, all blanks in recording file names are
  converted to underscores.
- The polarization can now be given in uppercase or lowercase characters in
  channels.conf.
- Fixed buffer initialization to work with DVB driver version 0.6.
- Implemented the "Simple Video Disk Recorder Protocol" (SVDRP) to control
  the VDR over a network connection.
- Implemented command line option handling.
- The program can now run in full background mode by using the --daemon option.
- Added a "summary" field to the timers (thanks to Carsten Koch!).
  This field can contain a descriptive text of the programme and will be
  displayed when the "Blue" key is pressed on a recording that was created by
  this timer. If the text contains the special character '|', a newline will
  be inserted at that place.  When pressing "Ok" on a timer that contains a
  summary field, the summary will be displayed. To edit such a timer the "Red"
  key must be pressed. Timers without a summary still go into Edit mode when
  pressing "Ok".  The summary field can only be filled in directly by editing
  the 'timers.conf' file with a text editor, or by defining/modifying the timer
  via the SVDRP interface.

- Support for more than one DVB card.
- Simultaneous record and replay (with two DVB cards).
- Instant recordings no longer get the name "instant". They now get the name
  of the channel, with a prepended '@' character.
- Timers that are not given an explicit Name now use the channel name with
  a prepended '@' character.
- If an instant recording is currently active, the Main menu now contains
  an option to stop that recording.
- Timers are now only processed when the Menu is not active. So after editing
  a timer the effect will take place only after the menu has been closed.
  In order to avoid missing a timer event by inadvertently leaving the menu
  open, the menu will be closed automatically after about two minutes of
  inactivity.
- If a recording is currently being replayed, the Main menu now contains an
  option to stop replaying.
- Displaying the recording DVB interface status in the decimal points of the
  RCU display.
- Reduced the number of remote control keys. Modified the key assignments for
  the PC keyboard to better resemble the "up-down-left-right-ok" layout on
  menu controlling remote control units.

- Changed name from 'osm' to 'vdr' to avoid mixups with the 'oms' program that
  appears to be in use with DVD replay.
- Implemented a channel display in the top menu line.
- Implemented replay progress display (press "Ok" when replaying to bring it up).
- Implemented direct channel selecting by pressing the numeric keys.
- Added several 'const' keywords to please stricter compilers.
- The repeat function for the remote control no longer adapts dynamically
  to the timing of the RCU (this sometimes caused the repeat function to
  kick in too early).
- Channel selection is now blocked when recording or replaying.
- Improved process handling.

- Actual record/replay now works.
- Dropped the idea of different "recording qualities" (a 36GB harddisk is
  able to store some 18 hours in full quality, so we don't really need that).
- Termination signals are now caught and the program cleans up before exiting.
- Support for CICAM.