| Age | Commit message (Collapse) | Author |
|---|
|
- The EIT information is now gathered in a separate thread.
- The sytem time can now be synchronized to the time broadcast in the DVB data
stream. This can be enabled in the "Setup" menu by setting "SetSystemTime" to
1. Note that this works only if VDR is running under a user id that has
permisson to set the system time.
- The new item "Schedule" in the "Main" menu opens VDR's EPG (thanks to Robert
Schneider). See the MANUAL file for a detailed description.
- The new setup parameters MarginStart and MarginStop define how long (in
minutes) before the official start time of a broadcast VDR shall begin
recording, and how long after the official end time it shall stop recording.
These are used when a recording is programmed from the "Schedules" menu.
- The delay value in the dvb.c.071.diff patch to the driver has been increased
to '3', because on some systems the OSD was not displayed correctly. If you
are running an already patched version 0.71 driver and encounter problems
with the OSD, please make sure the parameter in the ddelay call is '3', not
'2'.
- Fixed initializing the RCU remote control code (didn't work after switching
on the system).
- Problematic characters in recording names (which can come from timers that
are programmed via the "Schedules" menu) are now replaced by suitable
substitutes.
|
|
- Remote control data is now received in a separate thread, which makes things
a lot smoother.
- Repeat and release of remote control keys is now explicitly distinguished.
- In replay mode the search forward/back and skip functions now have two modes:
Pressing the key shortly and releasing it starts the function, and pressing it
again stops it. Pressing and holding down the key starts the function and
releasing the key stops it.
- The '@' character that marks an "instant recording" can now be turned off
in the "Setup" menu (thanks to Matthias Schniedermeyer).
- Pressing the "Back" button while replaying now stops replaying and brings up
the "Recordings" menu (suggested by Carsten Koch). This can be used to easily
delete a recording after watching it, or to switch to a different recording.
- The "Recordings" menu now places the cursor on the last replayed recording, if
that file still exists.
- The "Blue" button in the "Main" menu can now be used to "Resume" a previously
stopped replay session (suggested by Martin Hammerschmid).
- The low and high LNB frequencies can now be changed in the "Setup" menu.
|
|
- Modified LIRC interface to better handle repeat function.
- Faster OSD by first writing into a bitmap and then sending the entire bitmap
to the DVB driver at once (requires the patch 'dvb.c.071.diff' to be applied
against the version 0.71 DVB driver file 'dvb.c').
- When switching channels the channel is now immediately displayed, and the
current/next information is shown as soon as it becomes available.
- No longer displaying the year in the 'Recordings' menu to saves space for the
title.
- The 'Recordings' menu now displays a '*' to indicate new recordings.
- Added the description of the timers.conf file to the FORMATS file (thanks to
Bastian Guse).
- Displaying as much as possible of the current/next info (dropping characters
that would display only partially).
- In normal viewing mode the '0' key now toggles between the current and the
previous channel.
|
|
- NOTE: If you are using DVB driver version 0.7 you need to load the dvb.o
module with option outstream=0, so your insmod statement should read
'insmod dvb.o outstream=0'. This is currently necessary because 'vdr'
still works with AV_PES data.
- Video files now have the 'group read' bit set.
- Fixed handling errors in 'readstring()'.
- Handling SIGPIPE and re-establishing handler after intercepting a signal.
- The configuration files are now by default read from the video directory.
This can be changed by using the new '-c' option. Make sure you copy your
current '*.conf' files to your video directory ('/video' by default), or
use "-c ." to get the old behaviour of loading the configuration files
from the current directory.
- Waiting for input is now handled by a common function, which improves
response time on user actions. As a consequence the EIT data may sometimes
not be displayed, but this will change later when cEIT runs as a separate
thread.
- The new SVDRP command 'HITK' (thanks to Guido Fiala!) can be used to 'hit'
a remote control key. Establish an SVDRP connection and enter HITK without
a parameter for a list of all valid key names.
- The new SVDRP command 'GRAB' (thanks to Guido Fiala!) can be used to grab
the current frame and save it to a file.
- The new SVDRP commands 'OVL*' can be used to control video overlays (thanks
to Guido Fiala!). This is mainly for use in the 'kvdr' tool (see the 'kvdr'
page at http://www.s.netic.de/gfiala).
- If the name of the video directory used with the '-v' option had trailing
slashes, the recording file names have been damaged. Trailing slashes are
now silently removed.
- Fixed a buffer overflow in EIT parsing.
- Added a security warning regarding SVDRP to the INSTALL file.
- Fixed 'confirm' dialog.
- The daemon mode (option '-d') now no longer works with REMOTE=KBD (there
is no stdin in daemon mode, so KBD makes no sense - plus it sometimes
crashed).
|
|
- The new "Setup" menu allows the user to configure several parameters to his/her
personal taste (see MANUAL for details).
- Workaround for a driver timing problem in cDvbApi::Cmd(), which sometimes caused
the OSD to no longer be displayed (thanks to Niels de Carpentier).
- Added the '-m486' option to the compiler call.
- If a channel name contains a colon (':') it is now replaced with a '|' in
channels.conf.
- Not everybody appears to like the "page scrolling" mechanism introduced by
Heino Goldenstein in version 0.61, so this is now configurable via the "Setup"
menu.
- The new 'dvbrc2vdr' tool (thanks to Plamen Ganev!) can be used to convert
'dvbrc' channel files into 'vdr' format.
- Channels can now be "grouped" (thanks to Plamen Ganev!). See MANUAL for details.
There is currently no mechanism to define and maintain "Channel groups" via
the menu, so you'll have to insert "Channel group" control lines into your
'channels.conf' file manually (for example with a text editor).
- Started a new file named FORMATS with a description of the various file
formats used by VDR.
- The "Primary DVB interface" can now be chosen via the "Setup" menu.
- Display of the "current/next" information when switching channels can now
be disabled via the "Setup" menu.
- The "current/next" display now only shows those lines that actually contain
information.
- When directly selecting a channel by entering the channel number, the digits
entered so far together with the name of that channel are displayed on the
OSD (suggested by Martin Hammerschmid).
|
|
- The Makefile now defines DVBDIR to easily point to where the DVB driver
source is located.
- When switching channels the current/next information is now displayed if
available (thanks to Robert Schneider). Since there is now more information
to read when switching channels, the timeout for displaying it has been
increased from 2 to 5 seconds (remember that this info can always be recalled
by pressing the "Ok" button).
For this feature to work it is necessary that the 'Pnr' parameter in the
channel setup ('channels.conf') is set to the proper value. This has been
done for some of the channels in the default 'channels.conf'. Some other
parameters in the default 'channels.conf' have also been updated, so please
make sure your timers still use the correct channels!
|
|
- When scrolling through a list it now moves a full page up or down when the
cursor reaches the top or bottom of the menu (thanks to Heino Goldenstein!).
- Added missing '#include <sys/stat.h>' to recording.c.
- The video directory can now be defined with the command line option -v.
- There can now be more than one video directory (in case you have several
disks).
- Fixed learning key codes for PC keyboard.
- New command line option '-l' to set the log level.
- Times in timers.conf are now always printed with 4 digits (leading '0').
- Slow forward/back mode (thanks to Guido Fiala!).
- The "Up" key in replay mode no longer restarts replay at the very beginning,
but rather resumes normal replay mode after a "pause", "forward" or "backward"
operation. Use the "Skip -60s" function repeatedly to go back to the beginning
of the recording.
- Improved reaction on user input in fast/slow forward/back modes.
- No more upper limit for the value of 'Pnr'.
- Checking if the video card is really a DVB card.
- New SVDRP command UPDT to update an existing timer (or add a new one if it
doesn't yet exist).
- New version of the 'epg2timers' tool (with a modified channel list).
- Bugfix in closing window in DEBUG_OSD mode.
|
|
- Added support for LIRC remote control (thanks to Carsten Koch!).
There are now three different remote control modes: KBD (PC-Keyboard), RCU
and LIRC. See the INSTALL file for information on how to enable either of
these modes. The default mode is now KBD, not RCU as before (to make it
work immediately even if there is no actual remote control).
- Fixed small bug in dvbapi.c that was causing some channels (many on hotbird)
not to be correctly tuned (thanks to Plamen Ganev!).
- Now clearing the replay buffer in search forward/back, which results in
faster reaction.
- The 'Recordings' menu is now listed alphabetically (thanks to Carsten Koch!).
- The new 'epg2timers' tool (thanks to Carsten Koch!) can be used to convert
an EPG "merkliste" page (http://www.tvtv.de) to vdr timer entries.
- The new 'xtvrc2vdr' tool (thanks to Plamen Ganev!) can be used to convert
'xtvrc' channel files into 'vdr' format.
- When more than one timer matches at the same time, the first one in the list
with the highest 'Priority' is selected.
- The MANUAL section on "Programming the Timer" has been filled in.
- The year in the "Recordings" menu as well as in the progress display during
replay has been reduced to 2 digits to allow more space for the recording's
title. In the internal file structure the year is still stored with 4 digits,
so there will be no problem at the next turn of the century ;-)
- Channel names and timer filenames can now contain blanks. To avoid problems
with file names that contain blanks, all blanks in recording file names are
converted to underscores.
- The polarization can now be given in uppercase or lowercase characters in
channels.conf.
- Fixed buffer initialization to work with DVB driver version 0.6.
- Implemented the "Simple Video Disk Recorder Protocol" (SVDRP) to control
the VDR over a network connection.
- Implemented command line option handling.
- The program can now run in full background mode by using the --daemon option.
- Added a "summary" field to the timers (thanks to Carsten Koch!).
This field can contain a descriptive text of the programme and will be
displayed when the "Blue" key is pressed on a recording that was created by
this timer. If the text contains the special character '|', a newline will
be inserted at that place. When pressing "Ok" on a timer that contains a
summary field, the summary will be displayed. To edit such a timer the "Red"
key must be pressed. Timers without a summary still go into Edit mode when
pressing "Ok". The summary field can only be filled in directly by editing
the 'timers.conf' file with a text editor, or by defining/modifying the timer
via the SVDRP interface.
|
|
- Added support for LIRC remote control (thanks to Carsten Koch!).
There are now three different remote control modes: KBD (PC-Keyboard), RCU
and LIRC. See the INSTALL file for information on how to enable either of
these modes. The default mode is now KBD, not RCU as before (to make it
work immediately even if there is no actual remote control).
|
|
- Changed name from 'osm' to 'vdr' to avoid mixups with the 'oms' program that
appears to be in use with DVD replay.
- Implemented a channel display in the top menu line.
- Implemented replay progress display (press "Ok" when replaying to bring it up).
- Implemented direct channel selecting by pressing the numeric keys.
- Added several 'const' keywords to please stricter compilers.
- The repeat function for the remote control no longer adapts dynamically
to the timing of the RCU (this sometimes caused the repeat function to
kick in too early).
- Channel selection is now blocked when recording or replaying.
- Improved process handling.
|
|
- Fixed compilation with only DEBUG_REMOTE=1.
- Menus now use colors.
- Support for "Red", "Green", "Yellow", "Blue" buttons.
- Channels and Timers can now be added, deleted and moved.
- Basic record/play file handling support (no actual record/playback yet).
|
|
|
