| Age | Commit message (Collapse) | Author |
|---|
|
- Modified the display of the channel group separators (thanks to Markus Lang
for this suggestion).
- Added support for replaying DVDs (thanks to Andreas Schultz). See INSTALL for
instructions on how to compile VDR with DVD support.
- Fixed replay progress display in case replay is paused while watching an
ongoing recording.
- Ringbuffer uses semaphores to signal empty/full conditions.
- Fixed calculating the timeout value in cFile::FileReady() (thanks to
Wolfgang Henselmann-Weiss).
|
|
- Added Norwegian language texts (thanks to Jørgen Tvedt).
- Increased the usleep value in cDvbOsd::Cmd() to 5000 in order to work on
systems with the KURT/utime-patch (thanks to Guido Fiala).
- Changed the check whether the driver is loaded in runvdr to check for the
'dvb' module (the last one loaded).
- Fixed repeat function with LIRC (thanks to Stefan Huelswitt).
- Increased the upper limit for the symbol rate to 30000 (thanks to Ulrich
Röder).
- Made the position of the channel display configurable (thanks to Stefan
Huelswitt).
- Made the width and height of the OSD configurable (thanks to Stefan Huelswitt).
- DiSEqC support can now be generally enabled/disabled in the Setup menu. This
may be necessary if your multiswitch gets irritated by the default DiSEqC
codes '0' (thanks to Markus Lang).
- Fixed replaying in case there is no index file.
- Fixed jumping to an editing mark when replay has been paused.
- Avoiding unnecessary code execution in the replay progress display (thanks
to Guido Fiala).
- When entering time values the digits that still have to be entered are now
shown as '-' (as in "1-:--").
- When setting an editing mark while the progress display is not active, the
display will now be turned on for a short while to indicate the successful
setting of the mark.
- Updated 'channels.conf' for Premiere World (thanks to Helmut Schächner).
Check your timers if you use this channels.conf file, since the sequence of
several PW channels has been changed.
- Changed the color of "Info" messages to "black on green" and that of the
confirmation messages (like "Delete...") to "black on yellow".
- Fixed display with DEBUG_OSD (it still crashes sometimes, esp. when replaying,
but I can't seem to find what causes this... any ideas anybody?).
- Avoiding audio/video distortions in 'Transfer Mode' by no longer actually
tuning the primary interface (which can't receive this channel, anyway).
Apparently the driver gets irritated when the channel is switched and a
replay session is started immediately after that.
- Increased timeout until reporting "video data stream broken" when recording.
- Explicitly switching back to the previously active channel after ending a
replay session (to have it shown correctly in case it was in 'Transfer Mode').
|
|
- Fixed 'Transfer Mode' in cases where a non-primary interface was switched to
a channel that only the primary interface can receive (which could happen in
the EPG scanner).
- The EPG scanner now starts with the first channel (it used to start with the
second channel).
- Reacitvated setting the PNR.
- Adapted the frame scanning to the new muxing of the driver.
- The new compile time option REMOTE=NONE can be used to compile VDR without
any remote control support (for applications where it shall be controlled
exclusively via SVDRP).
- The new command line option -D can be used to define which DVB interfaces
a certain instance of VDR shall use.
- The "Left" and "Right" keys are now used to page up and down in lists (thanks
to Martin Hammerschmid). Since the "Timers" menu already uses these keys to
(de)activate timers, this functionality is not available there.
- The "Main" and "Commands" menu now support "hotkeys", which means that if the
first non-blank character of a menu item is a digit in the range 1..9, that
item can be selected by pressing the respective numeric key on the remote
control.
- The channel data in 'channels.conf' now contains the teletext PID (thanks to
Dave Chapman). Existing files will be read normally (and the teletext PID set
to 0), but once they are written back (due to some channel editing) the file
will have the new format.
- The EPG scanner now scans each transponder only once per cycle.
- Deleted recordings are now automatically removed from disk after a while (not
only when disk space is being needed for a new recording).
- Fixed repeat function in LIRC remote control.
- Changed the MAXDVBAPI macro in dvbapi.c to 4 in order to directly support the
maximum possible number of DVB cards.
- The 'Ca' parameter in the default 'channels.conf' has been changed from '2'
to '3' because the VDR prototype now has 3 DVB cards (and currently the CAM
module only works if it is inserted into the last DVB card).
- The "Now", "Next" and "Schedule" menus now remember the current channel and
restore the list when switching between them.
- The "Green" button in the "Recordings" menu can now be used to rewind a
recording and play it from the very beginning.
- Fixed handling ':' in timer filenames and '\n' in timer summaries (see FORMATS).
- When removing recordings empty directories are now removed from the video
directory.
- Added the "schnitt" tools from Matthias Schniedermeyer.
- New SVDRP command MESG to display a short message on the OSD.
- The Perl script 'svdrpsend.pl' can be used to send SVDRP commands to VDR.
- SVDRP can now immediately reuse the same port if VDR is restarted.
- SVDRP now has a timeout after which the connection is automatically closed
(default is 300 seconds, can be changed in "Setup").
- The compile time switch VFAT can be used to make VDR avoid the ':' character
in file names (VFAT can't handle them). Do 'make VFAT=1' to enable this.
- Support for DVB-C (thanks to Hans-Peter Raschke and Peter Hofmann).
See the INSTALL file for more information about the use of VDR with cable.
- Fixed an occasional segfault in the EIT processor.
- A value of '0' for the EPGScanTimeout setup parameter now completely turns off
scanning for EPG data on both single and multiple card systems.
- New setup parameter "PrimaryLimit" that allows to prevent timers from using the
primary DVB interface in multi card systems. Default value is 0, which means
that every timer may use the primary interface.
- The 'active' field of a timer will now be explicitly set to '1' if the user
modifies an active timer (see FORMATS for details).
- The new command line option -w can be used to activate a watchdog that makes
VDR exit in case the main program loop does not respond for more than the
given number of seconds. This is mainly useful in combination with the new
'runvdr' script that restarts VDR in case is has exited.
|
|
- VDR now requires driver version 0.8.1 or higher.
- Recordings are now saved in PES mode. Note that you now need to install the
driver *WITHOUT* 'outstream=0'! This is the default when you 'make insmod' in
the DVB/driver directory.
Old recordings (in AV_PES mode) can still be replayed (as long as the driver
still supports replaying AV_PES files). The only limitation with this is that
in fast forward/back mode the picture may be slightly distorted and there may
be sound fragments.
- The EPG data is now dumped into the file /video/epg.data every ten minutes.
Use the Perl script 'epg2html.pl' to convert the raw EPG data into a simple
HTML programme listing.
- Fixed handling of channel switching with the "Blue" button in the "What's on
now/next?" menus.
- Fixed saving the MarginStop setup parameter.
- Fixed missing initialization in cConfig.
- Implemented "On Disk Editing".
- There is no more default 'timers.conf' file.
- Added Italian language texts (thanks to Alberto Carraro).
- Fixed starting a replay session when the program is currently in "transfer
mode".
- Fixed setting/modifying timers via SVDRP with empty summary fields.
- Fixed a problem with recordings that have a single quote character in their
name (this is now mapped to 0x01).
- Changed the value for Diseqc to '0' in the default 'channels.conf'.
- Fixed displaying channels and recording status in the RCU's LED display when
a recording is interrupted due to higher priority.
- Implemented safe writing of config files (first writes into a temporary file
and then renames it).
- In case the video data stream is broken the log message will come only every
5 seconds.
- The current channel is now saved in the 'setup.conf' file when VDR is cancelled,
and will be restored next time it is started (thanks to Deti Fliegl).
- The EIT scanning thread is now locked when switching channels to avoid problems.
- Encrypted channels can now be selected even without knowing the PNR (however, it
is still necessary for the EPG info).
|
|
- Date and time in the title of an event info page are now always right adjusted.
- The 'current channel' is now handled device specific (in case there is more
than one DVB card).
- The 'SetSystemTime' option in the "Setup" menu is now shown as "yes/no".
- Implemented "internationalization" (see 'i18n.c' for information on how to
add new languages). Thanks to Miha Setina for translating the OSD texts to
the Slovenian language.
- Fixed learning keys on the PC keyboard (display oscillated).
- Fixed a timing problem with OSD refresh and SVDRP.
- Avoiding multiple definitions of the same timer in the "Schedule" menu (this
could happen when pressing the "Red" button while editing the timer).
- There can now be a configuration file named 'commands.conf' that defines
commands that can be executed through the "Main" menu's "Commands" option
(see FORMATS for details on how to define these commands).
- Added a 'fixed' font for use with the output of system commands.
- The 'Priority' parameter of the timers is now also used to interrupt a low
priority timer recording if a higher priority timer wants to record.
- A timer recording on a DVB card with a CAM module will now be interrupted
by a timer that needs to use this specific DVB card to record an encrypted
channel, if the timer currently occupying this DVB card doesn't need the
CAM module (and thus can continue recording on a different DVB card).
- The "Yellow" button in the "What's on now/next?" menus now displays the
schedule of the current channel from that menu.
- All DVB cards in a multi-card system now write their EIT information into the
same data structure.
- If there is more than one DVB card in the system, the non-primary cards are
now used to periodically scan through the channels in order to keep the
EPG info up-to-date. Scanning kicks in after 60 seconds of user inactivity
(timeout in order to keep user interactions instantaneously) and each channel
that has the 'pnr' parameter defined in 'channels.conf' is switched to for
20 seconds. If there is only one DVB card in the system, that card will start
scanning after 5 hours (configurable through the "Setup" menu) of user inactivity
and will switch back to the channel it originally displayed at the first sign of
user activity. Any scanning will only occur if that particular card is not
currently recording or replaying.
- Now shifting the 'Subtitle' info into the 'ExtendedDescription' on stations
that don't send the EIT information correctly (like, e.g., 'VOX').
- Implemented a 10 seconds latency when removing files.
- Fixed unwanted reaction on the "Green" and "Yellow" button in the "Event" display.
- Implemented 'Transfer Mode' to display video data from the DVB card that actually
can receive a certain channel on the primary interface. This is currently in
an early state and may still cause some problems, but it appears to work nice
already.
|
|
- The EIT information is now gathered in a separate thread.
- The sytem time can now be synchronized to the time broadcast in the DVB data
stream. This can be enabled in the "Setup" menu by setting "SetSystemTime" to
1. Note that this works only if VDR is running under a user id that has
permisson to set the system time.
- The new item "Schedule" in the "Main" menu opens VDR's EPG (thanks to Robert
Schneider). See the MANUAL file for a detailed description.
- The new setup parameters MarginStart and MarginStop define how long (in
minutes) before the official start time of a broadcast VDR shall begin
recording, and how long after the official end time it shall stop recording.
These are used when a recording is programmed from the "Schedules" menu.
- The delay value in the dvb.c.071.diff patch to the driver has been increased
to '3', because on some systems the OSD was not displayed correctly. If you
are running an already patched version 0.71 driver and encounter problems
with the OSD, please make sure the parameter in the ddelay call is '3', not
'2'.
- Fixed initializing the RCU remote control code (didn't work after switching
on the system).
- Problematic characters in recording names (which can come from timers that
are programmed via the "Schedules" menu) are now replaced by suitable
substitutes.
|
|
- The new "Setup" menu allows the user to configure several parameters to his/her
personal taste (see MANUAL for details).
- Workaround for a driver timing problem in cDvbApi::Cmd(), which sometimes caused
the OSD to no longer be displayed (thanks to Niels de Carpentier).
- Added the '-m486' option to the compiler call.
- If a channel name contains a colon (':') it is now replaced with a '|' in
channels.conf.
- Not everybody appears to like the "page scrolling" mechanism introduced by
Heino Goldenstein in version 0.61, so this is now configurable via the "Setup"
menu.
- The new 'dvbrc2vdr' tool (thanks to Plamen Ganev!) can be used to convert
'dvbrc' channel files into 'vdr' format.
- Channels can now be "grouped" (thanks to Plamen Ganev!). See MANUAL for details.
There is currently no mechanism to define and maintain "Channel groups" via
the menu, so you'll have to insert "Channel group" control lines into your
'channels.conf' file manually (for example with a text editor).
- Started a new file named FORMATS with a description of the various file
formats used by VDR.
- The "Primary DVB interface" can now be chosen via the "Setup" menu.
- Display of the "current/next" information when switching channels can now
be disabled via the "Setup" menu.
- The "current/next" display now only shows those lines that actually contain
information.
- When directly selecting a channel by entering the channel number, the digits
entered so far together with the name of that channel are displayed on the
OSD (suggested by Martin Hammerschmid).
|
|
- Support for more than one DVB card.
- Simultaneous record and replay (with two DVB cards).
- Instant recordings no longer get the name "instant". They now get the name
of the channel, with a prepended '@' character.
- Timers that are not given an explicit Name now use the channel name with
a prepended '@' character.
- If an instant recording is currently active, the Main menu now contains
an option to stop that recording.
- Timers are now only processed when the Menu is not active. So after editing
a timer the effect will take place only after the menu has been closed.
In order to avoid missing a timer event by inadvertently leaving the menu
open, the menu will be closed automatically after about two minutes of
inactivity.
- If a recording is currently being replayed, the Main menu now contains an
option to stop replaying.
- Displaying the recording DVB interface status in the decimal points of the
RCU display.
- Reduced the number of remote control keys. Modified the key assignments for
the PC keyboard to better resemble the "up-down-left-right-ok" layout on
menu controlling remote control units.
|
|
- Changed name from 'osm' to 'vdr' to avoid mixups with the 'oms' program that
appears to be in use with DVD replay.
- Implemented a channel display in the top menu line.
- Implemented replay progress display (press "Ok" when replaying to bring it up).
- Implemented direct channel selecting by pressing the numeric keys.
- Added several 'const' keywords to please stricter compilers.
- The repeat function for the remote control no longer adapts dynamically
to the timing of the RCU (this sometimes caused the repeat function to
kick in too early).
- Channel selection is now blocked when recording or replaying.
- Improved process handling.
|
|
- Fixed compilation with only DEBUG_REMOTE=1.
- Menus now use colors.
- Support for "Red", "Green", "Yellow", "Blue" buttons.
- Channels and Timers can now be added, deleted and moved.
- Basic record/play file handling support (no actual record/playback yet).
|
|
|
