1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
|
Video Disk Recorder User's Manual
---------------------------------
* Navigating through the On Screen Menus
The "Main" menu can be called up with the "Menu" key of your remote
control unit. The "Up" and "Down" keys are used to select a specific
item. The "Left" and "Right" keys can be used to change options, and
the numeric keys allow direct input of numeric data. The "Ok" key
confirms any changes (or switches to a channel in the "Channels" menu).
The "Back" key goes back one level in the menu structure, discarding
any changes that might have been made in the current menu.
In the "Timers" menu, the current timer can be enabled or disabled with
the "Right" or "Left" key, respectively (enabled timers are marked with ">").
"Ok" here opens the "Edit timer" menu.
Textual options, like channel names or recording file names, can be edited
by pressing the "Right" button (which puts brackets around the current
character as in "[R]TL"), selecting the desired character position with
"Left" and "Right", and changing the character with the "Up" and "Down"
keys. "Ok" then confirms the changes.
The "Red", "Green", "Yellow" and "Blue" buttons have special meanings
in the various menus and are listed at the bottom of the on-screen-display.
At any point in the menu system, pressing the "Menu" key again will
immediately leave the menu system.
* Selecting a Channel
There are three ways to select a channel:
1. With no On Screen Menu displayed press the "Up" or "Down" key to switch
to the next higher or lower channel.
2. Press the "Menu" button to bring up the On Screen Menu, select "Channels"
and browse through the list with the "Up" and "Down" key; to switch to the
selected channel press "Ok".
2. Directly type in the channel number with the numeric keys ('0'..'9');
if no key is pressed for about half a second, the digits collected so
far will define the channel number.
After switching to a different channel the channel number and name, as well
as the current time are displayed at the top of the screen. This line
automatically goes away after about two seconds, or if any key is pressed.
To bring up the channel display without switching channels you can press
the "Ok" button.
* Instant Recording
You can start recording the current channel by pressing the "Record"
button. This will create a timer event named "@channelname" that starts
at the current time and records for two hours.
If you want to modify the recording time you need to edit the timer.
Stop instant recording by pressing the "Menu" button and selecting
"Stop Recording", or by disabling the timer.
* Replaying a Recording
All recordings are listed in the "Recordings" menu. Browse through the
list with the "Up" and "Down" button and press "Ok" (or the "Red" button)
to start playback.
Playback can be stopped via the Main menu by selecting "Stop replaying",
or by pressing the "Stop" button outside the menu.
* Replay Control
The following keys have the listed meaning in Replay mode:
- "Begin" Positions to beginning of the recording and starts playback
from there.
- "Pause" Halts playback at the current position. Press again to continue
playback.
- "Stop" Stops playback and stores the current position, so that
playback can be resumed later at that point.
- "Search" Runs playback forward or backward at a higher speed. Press
again to resume normal speed.
- "Skip" Skips about 60 seconds forward or backward.
- "Ok" Brings up the replay progress display, which shows the date,
time and title of the recording, a progress bar and the
current and total time of the recording.
Press "Ok" again to turn off the progress display.
* Programming the Timer
Use the "Timer" menu to maintain your list of timer controlled recordings.
|
