merge: v4l-dvb

8 files changed, 166 insertions, 63 deletions

diff --git a/linux/Documentation/video4linux/CARDLIST.au0828 b/linux/Documentation/video4linux/CARDLIST.au0828
index eedc399e8..aa05e5bb2 100644
--- a/linux/Documentation/video4linux/CARDLIST.au0828
+++ b/linux/Documentation/video4linux/CARDLIST.au0828
@@ -3,3 +3,4 @@
   2 -> Hauppauge HVR850                         (au0828)        [2040:7240]
   3 -> DViCO FusionHDTV USB                     (au0828)        [0fe9:d620]
   4 -> Hauppauge HVR950Q rev xxF8               (au0828)        [2040:7201,2040:7211,2040:7281]
+  5 -> Hauppauge Woodbury                       (au0828)        [2040:8200]
diff --git a/linux/drivers/media/dvb/frontends/au8522.c b/linux/drivers/media/dvb/frontends/au8522.c
index 37f6260e1..d968a1000 100644
--- a/linux/drivers/media/dvb/frontends/au8522.c
+++ b/linux/drivers/media/dvb/frontends/au8522.c
@@ -304,6 +304,70 @@ static int au8522_mse2snr_lookup(struct mse2snr_tab *tab, int sz, int mse,
 	return ret;
 }
 
+/* 3.25 MHz IF Frequency table */
+static struct {
+	u16 reg;
+	u16 data;
+} if_3_25_mhz_tab[] = {
+	{ 0x80b5, 0x00 },
+	{ 0x80b6, 0x3d },
+	{ 0x80b7, 0xa0 },
+};
+
+/* 4.00 MHz IF Frequency table */
+static struct {
+	u16 reg;
+	u16 data;
+} if_4_mhz_tab[] = {
+	{ 0x80b5, 0x00 },
+	{ 0x80b6, 0x4b },
+	{ 0x80b7, 0xd9 },
+};
+
+/* 6.00 MHz IF Frequency table */
+static struct {
+	u16 reg;
+	u16 data;
+} if_6_mhz_tab[] = {
+	{ 0x80b5, 0xfb },
+	{ 0x80b6, 0x8e },
+	{ 0x80b7, 0x39 },
+};
+
+static int au8522_set_if(struct dvb_frontend *fe, enum au8522_if_freq if_freq)
+{
+	struct au8522_state *state = fe->demodulator_priv;
+	int i;
+
+	switch (if_freq) {
+	case AU8522_IF_3_25MHZ:
+		dprintk("%s() 3.25 MHz\n", __func__);
+		for (i = 0; i < ARRAY_SIZE(if_3_25_mhz_tab); i++)
+			au8522_writereg(state,
+					if_3_25_mhz_tab[i].reg,
+					if_3_25_mhz_tab[i].data);
+		break;
+	case AU8522_IF_4MHZ:
+		dprintk("%s() 4.00 MHz\n", __func__);
+		for (i = 0; i < ARRAY_SIZE(if_4_mhz_tab); i++)
+			au8522_writereg(state,
+					if_4_mhz_tab[i].reg,
+					if_4_mhz_tab[i].data);
+		break;
+	case AU8522_IF_6MHZ:
+		dprintk("%s() 6.00 MHz\n", __func__);
+		for (i = 0; i < ARRAY_SIZE(if_6_mhz_tab); i++)
+			au8522_writereg(state,
+					if_6_mhz_tab[i].reg,
+					if_6_mhz_tab[i].data);
+		break;
+	default:
+		dprintk("%s() IF Frequency not supported\n", __func__);
+		return -EINVAL;
+	}
+	return 0;
+}
+
 /* VSB Modulation table */
 static struct {
 	u16 reg;
@@ -438,6 +502,7 @@ static int au8522_enable_modulation(struct dvb_frontend *fe,
 			au8522_writereg(state,
 				VSB_mod_tab[i].reg,
 				VSB_mod_tab[i].data);
+		au8522_set_if(fe, state->config->vsb_if);
 		break;
 	case QAM_64:
 	case QAM_256:
@@ -446,6 +511,7 @@ static int au8522_enable_modulation(struct dvb_frontend *fe,
 			au8522_writereg(state,
 				QAM_mod_tab[i].reg,
 				QAM_mod_tab[i].data);
+		au8522_set_if(fe, state->config->qam_if);
 		break;
 	default:
 		dprintk("%s() Invalid modulation\n", __func__);
diff --git a/linux/drivers/media/dvb/frontends/au8522.h b/linux/drivers/media/dvb/frontends/au8522.h
index d7affa3cd..afc9af26e 100644
--- a/linux/drivers/media/dvb/frontends/au8522.h
+++ b/linux/drivers/media/dvb/frontends/au8522.h
@@ -24,6 +24,12 @@
 
 #include <linux/dvb/frontend.h>
 
+enum au8522_if_freq {
+	AU8522_IF_6MHZ = 0,
+	AU8522_IF_4MHZ,
+	AU8522_IF_3_25MHZ,
+};
+
 struct au8522_config {
 	/* the demodulator's i2c address */
 	u8 demod_address;
@@ -32,6 +38,9 @@ struct au8522_config {
 #define AU8522_TUNERLOCKING 0
 #define AU8522_DEMODLOCKING 1
 	u8 status_mode;
+
+	enum au8522_if_freq vsb_if;
+	enum au8522_if_freq qam_if;
 };
 
 #if defined(CONFIG_DVB_AU8522) || 				\
diff --git a/linux/drivers/media/video/Kconfig b/linux/drivers/media/video/Kconfig
index d4a6e56a7..d6b1a106a 100644
--- a/linux/drivers/media/video/Kconfig
+++ b/linux/drivers/media/video/Kconfig
@@ -630,7 +630,7 @@ config VIDEO_ZORAN_ZR36060
 	depends on VIDEO_ZORAN
 	help
 	  Say Y to support Zoran boards based on 36060 chips.
-	  This includes Iomega Bus, Pinnacle DC10, Linux media Labs 33
+	  This includes Iomega Buz, Pinnacle DC10, Linux media Labs 33
 	  and 33 R10 and AverMedia 6 boards.
 
 config VIDEO_ZORAN_BUZ
@@ -784,6 +784,64 @@ config VIDEO_CAFE_CCIC
 	  CMOS camera controller.  This is the controller found on first-
 	  generation OLPC systems.
 
+config SOC_CAMERA
+	tristate "SoC camera support"
+	depends on VIDEO_V4L2 && HAS_DMA
+	select VIDEOBUF_GEN
+	help
+	  SoC Camera is a common API to several cameras, not connecting
+	  over a bus like PCI or USB. For example some i2c camera connected
+	  directly to the data bus of an SoC.
+
+config SOC_CAMERA_MT9M001
+	tristate "mt9m001 support"
+	depends on SOC_CAMERA && I2C
+	select GPIO_PCA953X if MT9M001_PCA9536_SWITCH
+	help
+	  This driver supports MT9M001 cameras from Micron, monochrome
+	  and colour models.
+
+config MT9M001_PCA9536_SWITCH
+	bool "pca9536 datawidth switch for mt9m001"
+	depends on SOC_CAMERA_MT9M001 && GENERIC_GPIO
+	help
+	  Select this if your MT9M001 camera uses a PCA9536 I2C GPIO
+	  extender to switch between 8 and 10 bit datawidth modes
+
+config SOC_CAMERA_MT9V022
+	tristate "mt9v022 support"
+	depends on SOC_CAMERA && I2C
+	select GPIO_PCA953X if MT9V022_PCA9536_SWITCH
+	help
+	  This driver supports MT9V022 cameras from Micron
+
+config MT9V022_PCA9536_SWITCH
+	bool "pca9536 datawidth switch for mt9v022"
+	depends on SOC_CAMERA_MT9V022 && GENERIC_GPIO
+	help
+	  Select this if your MT9V022 camera uses a PCA9536 I2C GPIO
+	  extender to switch between 8 and 10 bit datawidth modes
+
+config SOC_CAMERA_PLATFORM
+	tristate "platform camera support"
+	depends on SOC_CAMERA
+	help
+	  This is a generic SoC camera platform driver, useful for testing
+
+config VIDEO_PXA27x
+	tristate "PXA27x Quick Capture Interface driver"
+	depends on VIDEO_DEV && PXA27x && SOC_CAMERA
+	select VIDEOBUF_DMA_SG
+	---help---
+	  This is a v4l2 driver for the PXA27x Quick Capture Interface
+
+config VIDEO_SH_MOBILE_CEU
+	tristate "SuperH Mobile CEU Interface driver"
+	depends on VIDEO_DEV && SOC_CAMERA
+	select VIDEOBUF_DMA_CONTIG
+	---help---
+	  This is a v4l2 driver for the SuperH Mobile CEU Interface
+
 #
 # USB Multimedia device configuration
 #
@@ -822,8 +880,7 @@ config VIDEO_OVCAMCHIP
 
 config USB_W9968CF
 	tristate "USB W996[87]CF JPEG Dual Mode Camera support"
-	depends on VIDEO_V4L1 && I2C
-	select VIDEO_OVCAMCHIP
+	depends on VIDEO_V4L1 && I2C && VIDEO_OVCAMCHIP
 	---help---
 	  Say Y here if you want support for cameras based on OV681 or
 	  Winbond W9967CF/W9968CF JPEG USB Dual Mode Camera Chips.
@@ -914,64 +971,4 @@ config USB_S2255
 
 endif # V4L_USB_DRIVERS
 
-config SOC_CAMERA
-	tristate "SoC camera support"
-	depends on VIDEO_V4L2 && HAS_DMA
-	select VIDEOBUF_GEN
-	help
-	  SoC Camera is a common API to several cameras, not connecting
-	  over a bus like PCI or USB. For example some i2c camera connected
-	  directly to the data bus of an SoC.
-
-config SOC_CAMERA_MT9M001
-	tristate "mt9m001 support"
-	depends on SOC_CAMERA && I2C
-	select GPIO_PCA953X if MT9M001_PCA9536_SWITCH
-	help
-	  This driver supports MT9M001 cameras from Micron, monochrome
-	  and colour models.
-
-config MT9M001_PCA9536_SWITCH
-	bool "pca9536 datawidth switch for mt9m001"
-	depends on SOC_CAMERA_MT9M001 && GENERIC_GPIO
-	help
-	  Select this if your MT9M001 camera uses a PCA9536 I2C GPIO
-	  extender to switch between 8 and 10 bit datawidth modes
-
-config SOC_CAMERA_MT9V022
-	tristate "mt9v022 support"
-	depends on SOC_CAMERA && I2C
-	select GPIO_PCA953X if MT9V022_PCA9536_SWITCH
-	help
-	  This driver supports MT9V022 cameras from Micron
-
-config MT9V022_PCA9536_SWITCH
-	bool "pca9536 datawidth switch for mt9v022"
-	depends on SOC_CAMERA_MT9V022 && GENERIC_GPIO
-	help
-	  Select this if your MT9V022 camera uses a PCA9536 I2C GPIO
-	  extender to switch between 8 and 10 bit datawidth modes
-
-config SOC_CAMERA_PLATFORM
-	tristate "platform camera support"
-	depends on SOC_CAMERA
-	help
-	  This is a generic SoC camera platform driver, useful for testing
-
-config VIDEO_PXA27x
-	tristate "PXA27x Quick Capture Interface driver"
-	depends on VIDEO_DEV && PXA27x
-	select SOC_CAMERA
-	select VIDEOBUF_DMA_SG
-	---help---
-	  This is a v4l2 driver for the PXA27x Quick Capture Interface
-
-config VIDEO_SH_MOBILE_CEU
-	tristate "SuperH Mobile CEU Interface driver"
-	depends on VIDEO_DEV
-	select SOC_CAMERA
-	select VIDEOBUF_DMA_CONTIG
-	---help---
-	  This is a v4l2 driver for the SuperH Mobile CEU Interface
-
 endif # VIDEO_CAPTURE_DRIVERS
diff --git a/linux/drivers/media/video/au0828/Kconfig b/linux/drivers/media/video/au0828/Kconfig
index ed9a50f18..018f72b8e 100644
--- a/linux/drivers/media/video/au0828/Kconfig
+++ b/linux/drivers/media/video/au0828/Kconfig
@@ -7,6 +7,7 @@ config VIDEO_AU0828
 	select DVB_AU8522 if !DVB_FE_CUSTOMIZE
 	select MEDIA_TUNER_XC5000 if !DVB_FE_CUSTOMIZE
 	select MEDIA_TUNER_MXL5007T if !DVB_FE_CUSTOMIZE
+	select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMIZE
 	---help---
 	  This is a video4linux driver for Auvitek's USB device.
 
diff --git a/linux/drivers/media/video/au0828/au0828-cards.c b/linux/drivers/media/video/au0828/au0828-cards.c
index 443e59009..14b9fc9bb 100644
--- a/linux/drivers/media/video/au0828/au0828-cards.c
+++ b/linux/drivers/media/video/au0828/au0828-cards.c
@@ -38,6 +38,9 @@ struct au0828_board au0828_boards[] = {
 	[AU0828_BOARD_DVICO_FUSIONHDTV7] = {
 		.name	= "DViCO FusionHDTV USB",
 	},
+	[AU0828_BOARD_HAUPPAUGE_WOODBURY] = {
+		.name = "Hauppauge Woodbury",
+	},
 };
 
 /* Tuner callback function for au0828 boards. Currently only needed
@@ -115,6 +118,7 @@ void au0828_card_setup(struct au0828_dev *dev)
 	case AU0828_BOARD_HAUPPAUGE_HVR850:
 	case AU0828_BOARD_HAUPPAUGE_HVR950Q:
 	case AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL:
+	case AU0828_BOARD_HAUPPAUGE_WOODBURY:
 		if (dev->i2c_rc == 0)
 			hauppauge_eeprom(dev, eeprom+0xa0);
 		break;
@@ -134,6 +138,7 @@ void au0828_gpio_setup(struct au0828_dev *dev)
 	case AU0828_BOARD_HAUPPAUGE_HVR850:
 	case AU0828_BOARD_HAUPPAUGE_HVR950Q:
 	case AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL:
+	case AU0828_BOARD_HAUPPAUGE_WOODBURY:
 		/* GPIO's
 		 * 4 - CS5340
 		 * 5 - AU8522 Demodulator
@@ -205,6 +210,8 @@ struct usb_device_id au0828_usb_id_table [] = {
 		.driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL },
 	{ USB_DEVICE(0x2040, 0x7281),
 		.driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL },
+	{ USB_DEVICE(0x2040, 0x8200),
+		.driver_info = AU0828_BOARD_HAUPPAUGE_WOODBURY },
 	{ },
 };
 
diff --git a/linux/drivers/media/video/au0828/au0828-cards.h b/linux/drivers/media/video/au0828/au0828-cards.h
index c37f5fd0f..102ed03dc 100644
--- a/linux/drivers/media/video/au0828/au0828-cards.h
+++ b/linux/drivers/media/video/au0828/au0828-cards.h
@@ -24,3 +24,4 @@
 #define AU0828_BOARD_HAUPPAUGE_HVR850 	2
 #define AU0828_BOARD_DVICO_FUSIONHDTV7	3
 #define AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL	4
+#define AU0828_BOARD_HAUPPAUGE_WOODBURY	5
diff --git a/linux/drivers/media/video/au0828/au0828-dvb.c b/linux/drivers/media/video/au0828/au0828-dvb.c
index 4c1dfdd8d..b7b0591ef 100644
--- a/linux/drivers/media/video/au0828/au0828-dvb.c
+++ b/linux/drivers/media/video/au0828/au0828-dvb.c
@@ -30,6 +30,7 @@
 #include "au8522.h"
 #include "xc5000.h"
 #include "mxl5007t.h"
+#include "tda18271.h"
 
 DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
 
@@ -41,6 +42,13 @@ static struct au8522_config hauppauge_hvr950q_config = {
 	.status_mode   = AU8522_DEMODLOCKING,
 };
 
+static struct au8522_config hauppauge_woodbury_config = {
+	.demod_address = 0x8e >> 1,
+	.status_mode   = AU8522_DEMODLOCKING,
+	.qam_if        = AU8522_IF_4MHZ,
+	.vsb_if        = AU8522_IF_3_25MHZ,
+};
+
 static struct xc5000_config hauppauge_hvr950q_tunerconfig = {
 	.i2c_address      = 0x61,
 	.if_khz           = 6000,
@@ -52,6 +60,10 @@ static struct mxl5007t_config mxl5007t_hvr950q_config = {
 	.if_freq_hz = MxL_IF_6_MHZ,
 };
 
+static struct tda18271_config hauppauge_woodbury_tunerconfig = {
+	.gate    = TDA18271_GATE_DIGITAL,
+};
+
 /*-------------------------------------------------------------------*/
 #if LINUX_VERSION_CODE < KERNEL_VERSION(2, 6, 19)
 static void urb_completion(struct urb *purb, struct pt_regs *regs)
@@ -362,6 +374,15 @@ int au0828_dvb_register(struct au0828_dev *dev)
 				   &dev->i2c_adap, 0x60,
 				   &mxl5007t_hvr950q_config);
 		break;
+	case AU0828_BOARD_HAUPPAUGE_WOODBURY:
+		dvb->frontend = dvb_attach(au8522_attach,
+				&hauppauge_woodbury_config,
+				&dev->i2c_adap);
+		if (dvb->frontend != NULL)
+			dvb_attach(tda18271_attach, dvb->frontend,
+				   0x60, &dev->i2c_adap,
+				   &hauppauge_woodbury_tunerconfig);
+		break;
 	default:
 		printk(KERN_WARNING "The frontend of your DVB/ATSC card "
 		       "isn't supported yet\n");