diff options
Diffstat (limited to 'dvb-spec/sgml/frontend.sgml')
| -rw-r--r-- | dvb-spec/sgml/frontend.sgml | 1765 |
1 files changed, 0 insertions, 1765 deletions
diff --git a/dvb-spec/sgml/frontend.sgml b/dvb-spec/sgml/frontend.sgml deleted file mode 100644 index 91a749f70..000000000 --- a/dvb-spec/sgml/frontend.sgml +++ /dev/null @@ -1,1765 +0,0 @@ -<title>DVB Frontend API</title> - -<para>The DVB frontend device controls the tuner and DVB demodulator -hardware. It can be accessed through <emphasis -role="tt">/dev/dvb/adapter0/frontend0</emphasis>. Data types and and -ioctl definitions can be accessed by including <emphasis -role="tt">linux/dvb/frontend.h</emphasis> in your application.</para> - -<para>DVB frontends come in three varieties: DVB-S (satellite), DVB-C -(cable) and DVB-T (terrestrial). Transmission via the internet (DVB-IP) -is not yet handled by this API but a future extension is possible. For -DVB-S the frontend device also supports satellite equipment control -(SEC) via DiSEqC and V-SEC protocols. The DiSEqC (digital SEC) -specification is available from Eutelsat <emphasis -role="tt">http://www.eutelsat.org/</emphasis>.</para> - -<para>Note that the DVB API may also be used for MPEG decoder-only PCI -cards, in which case there exists no frontend device.</para> - -<section id="frontend_types"> -<title>Frontend Data Types</title> - -<section id="frontend_type"> -<title>frontend type</title> - -<para>For historical reasons frontend types are named after the type of modulation used in -transmission.</para> -<programlisting> - typedef enum fe_type { - FE_QPSK, /⋆ DVB-S ⋆/ - FE_QAM, /⋆ DVB-C ⋆/ - FE_OFDM /⋆ DVB-T ⋆/ - } fe_type_t; -</programlisting> - -</section> - -<section id="frontend_caps"> -<title>frontend capabilities</title> - -<para>Capabilities describe what a frontend can do. Some capabilities can only be supported for -a specific frontend type.</para> -<programlisting> - typedef enum fe_caps { - FE_IS_STUPID = 0, - FE_CAN_INVERSION_AUTO = 0x1, - FE_CAN_FEC_1_2 = 0x2, - FE_CAN_FEC_2_3 = 0x4, - FE_CAN_FEC_3_4 = 0x8, - FE_CAN_FEC_4_5 = 0x10, - FE_CAN_FEC_5_6 = 0x20, - FE_CAN_FEC_6_7 = 0x40, - FE_CAN_FEC_7_8 = 0x80, - FE_CAN_FEC_8_9 = 0x100, - FE_CAN_FEC_AUTO = 0x200, - FE_CAN_QPSK = 0x400, - FE_CAN_QAM_16 = 0x800, - FE_CAN_QAM_32 = 0x1000, - FE_CAN_QAM_64 = 0x2000, - FE_CAN_QAM_128 = 0x4000, - FE_CAN_QAM_256 = 0x8000, - FE_CAN_QAM_AUTO = 0x10000, - FE_CAN_TRANSMISSION_MODE_AUTO = 0x20000, - FE_CAN_BANDWIDTH_AUTO = 0x40000, - FE_CAN_GUARD_INTERVAL_AUTO = 0x80000, - FE_CAN_HIERARCHY_AUTO = 0x100000, - FE_CAN_MUTE_TS = 0x80000000, - FE_CAN_CLEAN_SETUP = 0x40000000 - } fe_caps_t; -</programlisting> -</section> - -<section id="frontend_info"> -<title>frontend information</title> - -<para>Information about the frontend ca be queried with FE_GET_INFO.</para> - -<programlisting> - struct dvb_frontend_info { - char name[128]; - fe_type_t type; - uint32_t frequency_min; - uint32_t frequency_max; - uint32_t frequency_stepsize; - uint32_t frequency_tolerance; - uint32_t symbol_rate_min; - uint32_t symbol_rate_max; - uint32_t symbol_rate_tolerance; /⋆ ppm ⋆/ - uint32_t notifier_delay; /⋆ ms ⋆/ - fe_caps_t caps; - }; -</programlisting> -</section> - -<section id="frontend_diseqc"> -<title>diseqc master command</title> - -<para>A message sent from the frontend to DiSEqC capable equipment.</para> -<programlisting> - struct dvb_diseqc_master_cmd { - uint8_t msg [6]; /⋆ { framing, address, command, data[3] } ⋆/ - uint8_t msg_len; /⋆ valid values are 3...6 ⋆/ - }; -</programlisting> -</section> -<section role="subsection"> -<title>diseqc slave reply</title> - -<para>A reply to the frontend from DiSEqC 2.0 capable equipment.</para> -<programlisting> - struct dvb_diseqc_slave_reply { - uint8_t msg [4]; /⋆ { framing, data [3] } ⋆/ - uint8_t msg_len; /⋆ valid values are 0...4, 0 means no msg ⋆/ - int timeout; /⋆ return from ioctl after timeout ms with ⋆/ - }; /⋆ errorcode when no message was received ⋆/ -</programlisting> -</section> - -<section id="frontend_diseqc_slave_reply"> -<title>diseqc slave reply</title> -<para>The voltage is usually used with non-DiSEqC capable LNBs to switch the polarzation -(horizontal/vertical). When using DiSEqC epuipment this voltage has to be switched -consistently to the DiSEqC commands as described in the DiSEqC spec.</para> -<programlisting> - typedef enum fe_sec_voltage { - SEC_VOLTAGE_13, - SEC_VOLTAGE_18 - } fe_sec_voltage_t; -</programlisting> -</section> - -<section id="frontend_sec_tone"> -<title>SEC continuous tone</title> - -<para>The continous 22KHz tone is usually used with non-DiSEqC capable LNBs to switch the -high/low band of a dual-band LNB. When using DiSEqC epuipment this voltage has to -be switched consistently to the DiSEqC commands as described in the DiSEqC -spec.</para> -<programlisting> - typedef enum fe_sec_tone_mode { - SEC_TONE_ON, - SEC_TONE_OFF - } fe_sec_tone_mode_t; -</programlisting> -</section> - -<section id="frontend_sec_burst"> -<title>SEC tone burst</title> - -<para>The 22KHz tone burst is usually used with non-DiSEqC capable switches to select -between two connected LNBs/satellites. When using DiSEqC epuipment this voltage has to -be switched consistently to the DiSEqC commands as described in the DiSEqC -spec.</para> -<programlisting> - typedef enum fe_sec_mini_cmd { - SEC_MINI_A, - SEC_MINI_B - } fe_sec_mini_cmd_t; -</programlisting> - -<para></para> -</section> - -<section id="frontend_status"> -<title>frontend status</title> -<para>Several functions of the frontend device use the fe_status data type defined -by</para> -<programlisting> - typedef enum fe_status { - FE_HAS_SIGNAL = 0x01, /⋆ found something above the noise level ⋆/ - FE_HAS_CARRIER = 0x02, /⋆ found a DVB signal ⋆/ - FE_HAS_VITERBI = 0x04, /⋆ FEC is stable ⋆/ - FE_HAS_SYNC = 0x08, /⋆ found sync bytes ⋆/ - FE_HAS_LOCK = 0x10, /⋆ everything's working... ⋆/ - FE_TIMEDOUT = 0x20, /⋆ no lock within the last ~2 seconds ⋆/ - FE_REINIT = 0x40 /⋆ frontend was reinitialized, ⋆/ - } fe_status_t; /⋆ application is recommned to reset ⋆/ -</programlisting> -<para>to indicate the current state and/or state changes of the frontend hardware. -</para> - -</section> - -<section id="frontend_params"> -<title>frontend parameters</title> -<para>The kind of parameters passed to the frontend device for tuning depend on -the kind of hardware you are using. All kinds of parameters are combined as an -union in the FrontendParameters structure:</para> -<programlisting> - struct dvb_frontend_parameters { - uint32_t frequency; /⋆ (absolute) frequency in Hz for QAM/OFDM ⋆/ - /⋆ intermediate frequency in kHz for QPSK ⋆/ - fe_spectral_inversion_t inversion; - union { - struct dvb_qpsk_parameters qpsk; - struct dvb_qam_parameters qam; - struct dvb_ofdm_parameters ofdm; - } u; - }; -</programlisting> -<para>For satellite QPSK frontends you have to use the <constant>QPSKParameters</constant> member defined by</para> -<programlisting> - struct dvb_qpsk_parameters { - uint32_t symbol_rate; /⋆ symbol rate in Symbols per second ⋆/ - fe_code_rate_t fec_inner; /⋆ forward error correction (see above) ⋆/ - }; -</programlisting> -<para>for cable QAM frontend you use the <constant>QAMParameters</constant> structure</para> -<programlisting> - struct dvb_qam_parameters { - uint32_t symbol_rate; /⋆ symbol rate in Symbols per second ⋆/ - fe_code_rate_t fec_inner; /⋆ forward error correction (see above) ⋆/ - fe_modulation_t modulation; /⋆ modulation type (see above) ⋆/ - }; -</programlisting> -<para>DVB-T frontends are supported by the <constant>OFDMParamters</constant> structure -</para> -<programlisting> - struct dvb_ofdm_parameters { - fe_bandwidth_t bandwidth; - fe_code_rate_t code_rate_HP; /⋆ high priority stream code rate ⋆/ - fe_code_rate_t code_rate_LP; /⋆ low priority stream code rate ⋆/ - fe_modulation_t constellation; /⋆ modulation type (see above) ⋆/ - fe_transmit_mode_t transmission_mode; - fe_guard_interval_t guard_interval; - fe_hierarchy_t hierarchy_information; - }; -</programlisting> -<para>In the case of QPSK frontends the <constant>Frequency</constant> field specifies the intermediate -frequency, i.e. the offset which is effectively added to the local oscillator frequency (LOF) of -the LNB. The intermediate frequency has to be specified in units of kHz. For QAM and -OFDM frontends the Frequency specifies the absolute frequency and is given in -Hz. -</para> -<para>The Inversion field can take one of these values: -</para> -<programlisting> - typedef enum fe_spectral_inversion { - INVERSION_OFF, - INVERSION_ON, - INVERSION_AUTO - } fe_spectral_inversion_t; -</programlisting> -<para>It indicates if spectral inversion should be presumed or not. In the automatic setting -(<constant>INVERSION_AUTO</constant>) the hardware will try to figure out the correct setting by -itself. -</para> -<para>The possible values for the <constant>FEC_inner</constant> field are -</para> -<programlisting> - typedef enum fe_code_rate { - FEC_NONE = 0, - FEC_1_2, - FEC_2_3, - FEC_3_4, - FEC_4_5, - FEC_5_6, - FEC_6_7, - FEC_7_8, - FEC_8_9, - FEC_AUTO - } fe_code_rate_t; -</programlisting> -<para>which correspond to error correction rates of 1/2, 2/3, etc., no error correction or auto -detection. -</para> -<para>For cable and terrestrial frontends (QAM and OFDM) one also has to specify the quadrature -modulation mode which can be one of the following: -</para> -<programlisting> - typedef enum fe_modulation { - QPSK, - QAM_16, - QAM_32, - QAM_64, - QAM_128, - QAM_256, - QAM_AUTO - } fe_modulation_t; -</programlisting> -<para>Finally, there are several more parameters for OFDM: -</para> -<programlisting> - typedef enum fe_transmit_mode { - TRANSMISSION_MODE_2K, - TRANSMISSION_MODE_8K, - TRANSMISSION_MODE_AUTO - } fe_transmit_mode_t; -</programlisting> - <programlisting> - typedef enum fe_bandwidth { - BANDWIDTH_8_MHZ, - BANDWIDTH_7_MHZ, - BANDWIDTH_6_MHZ, - BANDWIDTH_AUTO - } fe_bandwidth_t; -</programlisting> - <programlisting> - typedef enum fe_guard_interval { - GUARD_INTERVAL_1_32, - GUARD_INTERVAL_1_16, - GUARD_INTERVAL_1_8, - GUARD_INTERVAL_1_4, - GUARD_INTERVAL_AUTO - } fe_guard_interval_t; -</programlisting> - <programlisting> - typedef enum fe_hierarchy { - HIERARCHY_NONE, - HIERARCHY_1, - HIERARCHY_2, - HIERARCHY_4, - HIERARCHY_AUTO - } fe_hierarchy_t; -</programlisting> - -</section> - -<section id="frontend_events"> -<title>frontend events</title> - <programlisting> - struct dvb_frontend_event { - fe_status_t status; - struct dvb_frontend_parameters parameters; - }; -</programlisting> - </section> -</section> - - -<section id="frontend_fcalls"> -<title>Frontend Function Calls</title> - -<section id="frontend_f_open"> -<title>open()</title> -<para>DESCRIPTION</para> -<informaltable><tgroup cols="1"><tbody><row> -<entry align="char"> -<para>This system call opens a named frontend device (/dev/dvb/adapter0/frontend0) - for subsequent use. Usually the first thing to do after a successful open is to - find out the frontend type with FE_GET_INFO.</para> -<para>The device can be opened in read-only mode, which only allows monitoring of - device status and statistics, or read/write mode, which allows any kind of use - (e.g. performing tuning operations.) -</para> -<para>In a system with multiple front-ends, it is usually the case that multiple devices - cannot be open in read/write mode simultaneously. As long as a front-end - device is opened in read/write mode, other open() calls in read/write mode will - either fail or block, depending on whether non-blocking or blocking mode was - specified. A front-end device opened in blocking mode can later be put into - non-blocking mode (and vice versa) using the F_SETFL command of the fcntl - system call. This is a standard system call, documented in the Linux manual - page for fcntl. When an open() call has succeeded, the device will be ready - for use in the specified mode. This implies that the corresponding hardware is - powered up, and that other front-ends may have been powered down to make - that possible.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>SYNOPSIS</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int open(const char ⋆deviceName, int flags);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>const char - *deviceName</para> -</entry><entry - align="char"> -<para>Name of specific video device.</para> -</entry> - </row><row><entry - align="char"> -<para>int flags</para> -</entry><entry - align="char"> -<para>A bit-wise OR of the following flags:</para> -</entry> - </row><row><entry - align="char"> -</entry><entry - align="char"> -<para>O_RDONLY read-only access</para> -</entry> - </row><row><entry - align="char"> -</entry><entry - align="char"> -<para>O_RDWR read/write access</para> -</entry> - </row><row><entry - align="char"> -</entry><entry - align="char"> -<para>O_NONBLOCK open in non-blocking mode</para> -</entry> - </row><row><entry - align="char"> -</entry><entry - align="char"> -<para>(blocking mode is the default)</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>ENODEV</para> -</entry><entry - align="char"> -<para>Device driver not loaded/available.</para> -</entry> - </row><row><entry - align="char"> -<para>EINTERNAL</para> -</entry><entry - align="char"> -<para>Internal error.</para> -</entry> - </row><row><entry - align="char"> -<para>EBUSY</para> -</entry><entry - align="char"> -<para>Device or resource busy.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>Invalid argument.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_f_close"> -<title>close()</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This system call closes a previously opened front-end device. After closing - a front-end device, its corresponding hardware might be powered down - automatically.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int close(int fd);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_read_status"> -<title>FE_READ_STATUS</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call returns status information about the front-end. This call only - requires read-only access to the device.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = FE_READ_STATUS, - fe_status_t ⋆status);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> - -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_READ_STATUS for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>struct fe_status_t - *status</para> -</entry><entry - align="char"> -<para>Points to the location where the front-end status word is - to be stored.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>status points to invalid address.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_read_ber"> -<title>FE_READ_BER</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call returns the bit error rate for the signal currently - received/demodulated by the front-end. For this command, read-only access to - the device is sufficient.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = FE_READ_BER, - uint32_t ⋆ber);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_READ_BER for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>uint32_t *ber</para> -</entry><entry - align="char"> -<para>The bit error rate is stored into *ber.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>ber points to invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>ENOSIGNAL</para> -</entry><entry - align="char"> -<para>There is no signal, thus no meaningful bit error rate. Also - returned if the front-end is not turned on.</para> -</entry> - </row><row><entry - align="char"> -<para>ENOSYS</para> -</entry><entry - align="char"> -<para>Function not available for this device.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_read_snr"> -<title>FE_READ_SNR</title> - -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call returns the signal-to-noise ratio for the signal currently received - by the front-end. For this command, read-only access to the device is sufficient.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = FE_READ_SNR, int16_t - ⋆snr);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_READ_SNR for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>int16_t *snr</para> -</entry><entry - align="char"> -<para>The signal-to-noise ratio is stored into *snr.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>snr points to invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>ENOSIGNAL</para> -</entry><entry - align="char"> -<para>There is no signal, thus no meaningful signal strength - value. Also returned if front-end is not turned on.</para> -</entry> - </row><row><entry - align="char"> -<para>ENOSYS</para> -</entry><entry - align="char"> -<para>Function not available for this device.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_read_signal_strength"> -<title>FE_READ_SIGNAL_STRENGTH</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call returns the signal strength value for the signal currently received - by the front-end. For this command, read-only access to the device is sufficient.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl( int fd, int request = - FE_READ_SIGNAL_STRENGTH, int16_t ⋆strength);</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_READ_SIGNAL_STRENGTH for this - command.</para> -</entry> - </row><row><entry - align="char"> -<para>int16_t *strength</para> -</entry><entry - align="char"> -<para>The signal strength value is stored into *strength.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>status points to invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>ENOSIGNAL</para> -</entry><entry - align="char"> -<para>There is no signal, thus no meaningful signal strength - value. Also returned if front-end is not turned on.</para> -</entry> - </row><row><entry - align="char"> -<para>ENOSYS</para> -</entry><entry - align="char"> -<para>Function not available for this device.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_read_ub"> -<title>FE_READ_UNCORRECTED_BLOCKS</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call returns the number of uncorrected blocks detected by the device - driver during its lifetime. For meaningful measurements, the increment in block - count during a specific time interval should be calculated. For this command, - read-only access to the device is sufficient.</para> -</entry> - </row><row><entry - align="char"> -<para>Note that the counter will wrap to zero after its maximum count has been - reached.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl( int fd, int request = - FE_READ_UNCORRECTED_BLOCKS, uint32_t ⋆ublocks);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_READ_UNCORRECTED_BLOCKS for this - command.</para> -</entry> - </row><row><entry - align="char"> -<para>uint32_t *ublocks</para> -</entry><entry - align="char"> -<para>The total number of uncorrected blocks seen by the driver - so far.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>ublocks points to invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>ENOSYS</para> -</entry><entry - align="char"> -<para>Function not available for this device.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_set_fe"> -<title>FE_SET_FRONTEND</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call starts a tuning operation using specified parameters. The result - of this call will be successful if the parameters were valid and the tuning could - be initiated. The result of the tuning operation in itself, however, will arrive - asynchronously as an event (see documentation for FE_GET_EVENT and - FrontendEvent.) If a new FE_SET_FRONTEND operation is initiated before - the previous one was completed, the previous operation will be aborted in favor - of the new one. This command requires read/write access to the device.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = FE_SET_FRONTEND, - struct dvb_frontend_parameters ⋆p);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_SET_FRONTEND for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>struct - dvb_frontend_parameters - *p</para> -</entry><entry - align="char"> -<para>Points to parameters for tuning operation.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>p points to invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>Maximum supported symbol rate reached.</para> -</entry> -</row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_get_fe"> -<title>FE_GET_FRONTEND</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call queries the currently effective frontend parameters. For this - command, read-only access to the device is sufficient.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = FE_GET_FRONTEND, - struct dvb_frontend_parameters ⋆p);</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_SET_FRONTEND for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>struct - dvb_frontend_parameters - *p</para> -</entry><entry - align="char"> -<para>Points to parameters for tuning operation.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>ERRORS -</para> - -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>p points to invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>Maximum supported symbol rate reached.</para> -</entry> - </row></tbody></tgroup></informaltable> - -</section> - -<section id="frontend_get_event"> -<title>FE_GET_EVENT</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call returns a frontend event if available. If an event is not - available, the behavior depends on whether the device is in blocking or - non-blocking mode. In the latter case, the call fails immediately with errno - set to EWOULDBLOCK. In the former case, the call blocks until an event - becomes available.</para> -</entry> - </row><row><entry - align="char"> -<para>The standard Linux poll() and/or select() system calls can be used with the - device file descriptor to watch for new events. For select(), the file descriptor - should be included in the exceptfds argument, and for poll(), POLLPRI should - be specified as the wake-up condition. Since the event queue allocated is - rather small (room for 8 events), the queue must be serviced regularly to avoid - overflow. If an overflow happens, the oldest event is discarded from the queue, - and an error (EOVERFLOW) occurs the next time the queue is read. After - reporting the error condition in this fashion, subsequent FE_GET_EVENT - calls will return events from the queue as usual.</para> -</entry> - </row><row><entry - align="char"> -<para>For the sake of implementation simplicity, this command requires read/write - access to the device.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = QPSK_GET_EVENT, - struct dvb_frontend_event ⋆ev);</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_GET_EVENT for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>struct - dvb_frontend_event - *ev</para> -</entry><entry - align="char"> -<para>Points to the location where the event,</para> -</entry> - </row><row><entry - align="char"> -</entry><entry - align="char"> -<para>if any, is to be stored.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>ev points to invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>EWOULDBLOCK</para> -</entry><entry - align="char"> -<para>There is no event pending, and the device is in - non-blocking mode.</para> -</entry> - </row><row><entry - align="char"> -<para>EOVERFLOW</para> -</entry><entry - align="char"> -</entry> - </row><row><entry - align="char"> -</entry><entry - align="char"> -<para>Overflow in event queue - one or more events were lost.</para> -</entry> -</row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_get_info"> -<title>FE_GET_INFO</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call returns information about the front-end. This call only requires - read-only access to the device.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> - -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para> int ioctl(int fd, int request = FE_GET_INFO, struct - dvb_frontend_info ⋆info);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> - -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_GET_INFO for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>struct - dvb_frontend_info - *info</para> -</entry><entry - align="char"> -<para>Points to the location where the front-end information is - to be stored.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid open file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>info points to invalid address.</para> -</entry> -</row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_diseqc_reset_overload"> -<title>FE_DISEQC_RESET_OVERLOAD</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>If the bus has been automatically powered off due to power overload, this ioctl - call restores the power to the bus. The call requires read/write access to the - device. This call has no effect if the device is manually powered off. Not all - DVB adapters support this ioctl.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = - FE_DISEQC_RESET_OVERLOAD);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_DISEQC_RESET_OVERLOAD for this - command.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EPERM</para> -</entry><entry - align="char"> -<para>Permission denied (needs read/write access).</para> -</entry> - </row><row><entry - align="char"> -<para>EINTERNAL</para> -</entry><entry - align="char"> -<para>Internal error in the device driver.</para> -</entry> -</row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_diseqc_send_master_cmd"> -<title>FE_DISEQC_SEND_MASTER_CMD</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call is used to send a a DiSEqC command.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = - FE_DISEQC_SEND_MASTER_CMD, struct - dvb_diseqc_master_cmd ⋆cmd);</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_DISEQC_SEND_MASTER_CMD for this - command.</para> -</entry> - </row><row><entry - align="char"> -<para>struct - dvb_diseqc_master_cmd - *cmd</para> -</entry><entry - align="char"> -<para>Pointer to the command to be transmitted.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>Seq points to an invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>The data structure referred to by seq is invalid in some - way.</para> -</entry> - </row><row><entry - align="char"> -<para>EPERM</para> -</entry><entry - align="char"> -<para>Permission denied (needs read/write access).</para> -</entry> - </row><row><entry - align="char"> -<para>EINTERNAL</para> -</entry><entry - align="char"> -<para>Internal error in the device driver.</para> -</entry> -</row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_diseqc_recv_slave_reply"> -<title>FE_DISEQC_RECV_SLAVE_REPLY</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call is used to receive reply to a DiSEqC 2.0 command.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = - FE_DISEQC_RECV_SLAVE_REPLY, struct - dvb_diseqc_slave_reply ⋆reply);</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_DISEQC_RECV_SLAVE_REPLY for this - command.</para> -</entry> - </row><row><entry - align="char"> -<para>struct - dvb_diseqc_slave_reply - *reply</para> -</entry><entry - align="char"> -<para>Pointer to the command to be received.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>Seq points to an invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>The data structure referred to by seq is invalid in some - way.</para> -</entry> - </row><row><entry - align="char"> -<para>EPERM</para> -</entry><entry - align="char"> -<para>Permission denied (needs read/write access).</para> -</entry> - </row><row><entry - align="char"> -<para>EINTERNAL</para> -</entry><entry - align="char"> -<para>Internal error in the device driver.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_diseqc_send_burst"> -<title>FE_DISEQC_SEND_BURST</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This ioctl call is used to send a 22KHz tone burst.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = - FE_DISEQC_SEND_BURST, fe_sec_mini_cmd_t burst);</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_DISEQC_SEND_BURST for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>fe_sec_mini_cmd_t - burst</para> -</entry><entry - align="char"> -<para>burst A or B.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>EBADF</para> -</entry><entry - align="char"> -<para>fd is not a valid file descriptor.</para> -</entry> - </row><row><entry - align="char"> -<para>EFAULT</para> -</entry><entry - align="char"> -<para>Seq points to an invalid address.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>The data structure referred to by seq is invalid in some - way.</para> -</entry> - </row><row><entry - align="char"> -<para>EPERM</para> -</entry><entry - align="char"> -<para>Permission denied (needs read/write access).</para> -</entry> - </row><row><entry - align="char"> -<para>EINTERNAL</para> -</entry><entry - align="char"> -<para>Internal error in the device driver.</para> -</entry> -</row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_set_tone"> -<title>FE_SET_TONE</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This call is used to set the generation of the continuous 22kHz tone. This call - requires read/write permissions.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = FE_SET_TONE, - fe_sec_tone_mode_t tone);</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_SET_TONE for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>fe_sec_tone_mode_t - tone</para> -</entry><entry - align="char"> -<para>The requested tone generation mode (on/off).</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>ENODEV</para> -</entry><entry - align="char"> -<para>Device driver not loaded/available.</para> -</entry> - </row><row><entry - align="char"> -<para>EBUSY</para> -</entry><entry - align="char"> -<para>Device or resource busy.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>Invalid argument.</para> -</entry> - </row><row><entry - align="char"> -<para>EPERM</para> -</entry><entry - align="char"> -<para>File not opened with read permissions.</para> -</entry> - </row><row><entry - align="char"> -<para>EINTERNAL</para> -</entry><entry - align="char"> -<para>Internal error in the device driver.</para> -</entry> -</row></tbody></tgroup></informaltable> -</section> - -<section id="fe_set_voltage"> -<title>FE_SET_VOLTAGE</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>This call is used to set the bus voltage. This call requires read/write - permissions.</para> -</entry> - </row></tbody></tgroup></informaltable> -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = FE_SET_VOLTAGE, - fe_sec_voltage_t voltage);</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_SET_VOLTAGE for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>fe_sec_voltage_t - voltage</para> -</entry><entry - align="char"> -<para>The requested bus voltage.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>ENODEV</para> -</entry><entry - align="char"> -<para>Device driver not loaded/available.</para> -</entry> - </row><row><entry - align="char"> -<para>EBUSY</para> -</entry><entry - align="char"> -<para>Device or resource busy.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>Invalid argument.</para> -</entry> - </row><row><entry - align="char"> -<para>EPERM</para> -</entry><entry - align="char"> -<para>File not opened with read permissions.</para> -</entry> - </row><row><entry - align="char"> -<para>EINTERNAL</para> -</entry><entry - align="char"> -<para>Internal error in the device driver.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> - -<section id="frontend_enable_high_lnb_volt"> -<title>FE_ENABLE_HIGH_LNB_VOLTAGE</title> -<para>DESCRIPTION -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>If high != 0 enables slightly higher voltages instead of 13/18V (to compensate - for long cables). This call requires read/write permissions. Not all DVB - adapters support this ioctl.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>SYNOPSIS -</para> -<informaltable><tgroup cols="1"><tbody><row><entry - align="char"> -<para>int ioctl(int fd, int request = - FE_ENABLE_HIGH_LNB_VOLTAGE, int high);</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>PARAMETERS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>int fd</para> -</entry><entry - align="char"> -<para>File descriptor returned by a previous call to open().</para> -</entry> - </row><row><entry - align="char"> -<para>int request</para> -</entry><entry - align="char"> -<para>Equals FE_SET_VOLTAGE for this command.</para> -</entry> - </row><row><entry - align="char"> -<para>int high</para> -</entry><entry - align="char"> -<para>The requested bus voltage.</para> -</entry> - </row></tbody></tgroup></informaltable> - -<para>ERRORS -</para> -<informaltable><tgroup cols="2"><tbody><row><entry - align="char"> -<para>ENODEV</para> -</entry><entry - align="char"> -<para>Device driver not loaded/available.</para> -</entry> - </row><row><entry - align="char"> -<para>EBUSY</para> -</entry><entry - align="char"> -<para>Device or resource busy.</para> -</entry> - </row><row><entry - align="char"> -<para>EINVAL</para> -</entry><entry - align="char"> -<para>Invalid argument.</para> -</entry> - </row><row><entry - align="char"> -<para>EPERM</para> -</entry><entry - align="char"> -<para>File not opened with read permissions.</para> -</entry> - </row><row><entry - align="char"> -<para>EINTERNAL</para> -</entry><entry - align="char"> -<para>Internal error in the device driver.</para> -</entry> - </row></tbody></tgroup></informaltable> -</section> -</section> |