diff options
Diffstat (limited to 'linux')
| -rw-r--r-- | linux/drivers/media/dvb/Kconfig | 13 | ||||
| -rw-r--r-- | linux/drivers/media/dvb/dvb-core/dvb_frontend.c | 35 | ||||
| -rw-r--r-- | linux/drivers/media/dvb/dvb-core/dvbdev.h | 5 | ||||
| -rw-r--r-- | linux/drivers/media/video/gspca/mr97310a.c | 853 | ||||
| -rw-r--r-- | linux/drivers/media/video/gspca/pac207.c | 37 | ||||
| -rw-r--r-- | linux/drivers/media/video/vino.c | 1 | ||||
| -rw-r--r-- | linux/include/linux/videodev2.h | 1 |
7 files changed, 797 insertions, 148 deletions
diff --git a/linux/drivers/media/dvb/Kconfig b/linux/drivers/media/dvb/Kconfig index b01986918..1d0e4b1ef 100644 --- a/linux/drivers/media/dvb/Kconfig +++ b/linux/drivers/media/dvb/Kconfig @@ -2,6 +2,19 @@ # DVB device configuration # +config DVB_MAX_ADAPTERS + int "maximum number of DVB/ATSC adapters" + depends on DVB_CORE + default 8 + range 1 255 + help + Maximum number of DVB/ATSC adapters. Increasing this number + increases the memory consumption of the DVB subsystem even + if a much lower number of DVB/ATSC adapters is present. + Only values in the range 4-32 are tested. + + If you are unsure about this, use the default value 8 + config DVB_DYNAMIC_MINORS bool "Dynamic DVB minor allocation" depends on DVB_CORE diff --git a/linux/drivers/media/dvb/dvb-core/dvb_frontend.c b/linux/drivers/media/dvb/dvb-core/dvb_frontend.c index 41166d407..56a11d32a 100644 --- a/linux/drivers/media/dvb/dvb-core/dvb_frontend.c +++ b/linux/drivers/media/dvb/dvb-core/dvb_frontend.c @@ -77,6 +77,7 @@ MODULE_PARM_DESC(dvb_mfe_wait_time, "Wait up to <mfe_wait_time> seconds on open( #define FESTATE_ZIGZAG_FAST 32 #define FESTATE_ZIGZAG_SLOW 64 #define FESTATE_DISEQC 128 +#define FESTATE_ERROR 256 #define FESTATE_WAITFORLOCK (FESTATE_TUNING_FAST | FESTATE_TUNING_SLOW | FESTATE_ZIGZAG_FAST | FESTATE_ZIGZAG_SLOW | FESTATE_DISEQC) #define FESTATE_SEARCHING_FAST (FESTATE_TUNING_FAST | FESTATE_ZIGZAG_FAST) #define FESTATE_SEARCHING_SLOW (FESTATE_TUNING_SLOW | FESTATE_ZIGZAG_SLOW) @@ -274,6 +275,7 @@ static int dvb_frontend_swzigzag_autotune(struct dvb_frontend *fe, int check_wra { int autoinversion; int ready = 0; + int fe_set_err = 0; struct dvb_frontend_private *fepriv = fe->frontend_priv; int original_inversion = fepriv->parameters.inversion; u32 original_frequency = fepriv->parameters.frequency; @@ -350,7 +352,11 @@ static int dvb_frontend_swzigzag_autotune(struct dvb_frontend *fe, int check_wra if (autoinversion) fepriv->parameters.inversion = fepriv->inversion; if (fe->ops.set_frontend) - fe->ops.set_frontend(fe, &fepriv->parameters); + fe_set_err = fe->ops.set_frontend(fe, &fepriv->parameters); + if (fe_set_err < 0) { + fepriv->state = FESTATE_ERROR; + return fe_set_err; + } fepriv->parameters.frequency = original_frequency; fepriv->parameters.inversion = original_inversion; @@ -362,6 +368,7 @@ static int dvb_frontend_swzigzag_autotune(struct dvb_frontend *fe, int check_wra static void dvb_frontend_swzigzag(struct dvb_frontend *fe) { fe_status_t s = 0; + int retval = 0; struct dvb_frontend_private *fepriv = fe->frontend_priv; /* if we've got no parameters, just keep idling */ @@ -375,8 +382,12 @@ static void dvb_frontend_swzigzag(struct dvb_frontend *fe) if (fepriv->tune_mode_flags & FE_TUNE_MODE_ONESHOT) { if (fepriv->state & FESTATE_RETUNE) { if (fe->ops.set_frontend) - fe->ops.set_frontend(fe, &fepriv->parameters); - fepriv->state = FESTATE_TUNED; + retval = fe->ops.set_frontend(fe, + &fepriv->parameters); + if (retval < 0) + fepriv->state = FESTATE_ERROR; + else + fepriv->state = FESTATE_TUNED; } fepriv->delay = 3*HZ; fepriv->quality = 0; @@ -454,7 +465,11 @@ static void dvb_frontend_swzigzag(struct dvb_frontend *fe) fepriv->delay = fepriv->min_delay; /* peform a tune */ - if (dvb_frontend_swzigzag_autotune(fe, fepriv->check_wrapped)) { + retval = dvb_frontend_swzigzag_autotune(fe, + fepriv->check_wrapped); + if (retval < 0) { + return; + } else if (retval) { /* OK, if we've run out of trials at the fast speed. * Drop back to slow for the _next_ attempt */ fepriv->state = FESTATE_SEARCHING_SLOW; @@ -834,6 +849,15 @@ static int dvb_frontend_check_parameters(struct dvb_frontend *fe, } } + /* check for supported modulation */ + if (fe->ops.info.type == FE_QAM && + (parms->u.qam.modulation > QAM_AUTO || + !((1 << (parms->u.qam.modulation + 10)) & fe->ops.info.caps))) { + printk(KERN_WARNING "DVB: adapter %i frontend %i modulation %u not supported\n", + fe->dvb->num, fe->id, parms->u.qam.modulation); + return -EINVAL; + } + return 0; } @@ -1614,7 +1638,8 @@ static int dvb_frontend_ioctl_legacy(struct inode *inode, struct file *file, /* if retune was requested but hasn't occured yet, prevent * that user get signal state from previous tuning */ - if(fepriv->state == FESTATE_RETUNE) { + if (fepriv->state == FESTATE_RETUNE || + fepriv->state == FESTATE_ERROR) { err=0; *status = 0; break; diff --git a/linux/drivers/media/dvb/dvb-core/dvbdev.h b/linux/drivers/media/dvb/dvb-core/dvbdev.h index 487919bea..895e2efca 100644 --- a/linux/drivers/media/dvb/dvb-core/dvbdev.h +++ b/linux/drivers/media/dvb/dvb-core/dvbdev.h @@ -30,7 +30,12 @@ #define DVB_MAJOR 212 +#if defined(CONFIG_DVB_MAX_ADAPTERS) && CONFIG_DVB_MAX_ADAPTERS > 0 +#define DVB_MAX_ADAPTERS CONFIG_DVB_MAX_ADAPTERS +#else +#warning invalid CONFIG_DVB_MAX_ADAPTERS value #define DVB_MAX_ADAPTERS 8 +#endif #define DVB_UNSET (-1) diff --git a/linux/drivers/media/video/gspca/mr97310a.c b/linux/drivers/media/video/gspca/mr97310a.c index 301325134..140c8f320 100644 --- a/linux/drivers/media/video/gspca/mr97310a.c +++ b/linux/drivers/media/video/gspca/mr97310a.c @@ -3,6 +3,21 @@ * * Copyright (C) 2009 Kyle Guinn <elyk03@gmail.com> * + * Support for the MR97310A cameras in addition to the Aiptek Pencam VGA+ + * and for the routines for detecting and classifying these various cameras, + * + * Copyright (C) 2009 Theodore Kilgore <kilgota@auburn.edu> + * + * Acknowledgements: + * + * The MR97311A support in gspca/mars.c has been helpful in understanding some + * of the registers in these cameras. + * + * Hans de Goede <hdgoede@redhat.com> and + * Thomas Kaiser <thomas@kaiser-linux.li> + * have assisted with their experience. Each of them has also helped by + * testing a previously unsupported camera. + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -22,18 +37,108 @@ #include "gspca.h" -MODULE_AUTHOR("Kyle Guinn <elyk03@gmail.com>"); +#define CAM_TYPE_CIF 0 +#define CAM_TYPE_VGA 1 + +#define MR97310A_BRIGHTNESS_MIN -254 +#define MR97310A_BRIGHTNESS_MAX 255 +#define MR97310A_BRIGHTNESS_DEFAULT 0 + +#define MR97310A_EXPOSURE_MIN 300 +#define MR97310A_EXPOSURE_MAX 4095 +#define MR97310A_EXPOSURE_DEFAULT 1000 + +#define MR97310A_GAIN_MIN 0 +#define MR97310A_GAIN_MAX 31 +#define MR97310A_GAIN_DEFAULT 25 + +MODULE_AUTHOR("Kyle Guinn <elyk03@gmail.com>," + "Theodore Kilgore <kilgota@auburn.edu>"); MODULE_DESCRIPTION("GSPCA/Mars-Semi MR97310A USB Camera Driver"); MODULE_LICENSE("GPL"); +/* global parameters */ +int force_sensor_type = -1; +module_param(force_sensor_type, int, 0644); +MODULE_PARM_DESC(force_sensor_type, "Force sensor type (-1 (auto), 0 or 1)"); + /* specific webcam descriptor */ struct sd { struct gspca_dev gspca_dev; /* !! must be the first item */ u8 sof_read; + u8 cam_type; /* 0 is CIF and 1 is VGA */ + u8 sensor_type; /* We use 0 and 1 here, too. */ + u8 do_lcd_stop; + + int brightness; + u16 exposure; + u8 gain; +}; + +struct sensor_w_data { + u8 reg; + u8 flags; + u8 data[16]; + int len; }; +static int sd_setbrightness(struct gspca_dev *gspca_dev, __s32 val); +static int sd_getbrightness(struct gspca_dev *gspca_dev, __s32 *val); +static int sd_setexposure(struct gspca_dev *gspca_dev, __s32 val); +static int sd_getexposure(struct gspca_dev *gspca_dev, __s32 *val); +static int sd_setgain(struct gspca_dev *gspca_dev, __s32 val); +static int sd_getgain(struct gspca_dev *gspca_dev, __s32 *val); +static void setbrightness(struct gspca_dev *gspca_dev); +static void setexposure(struct gspca_dev *gspca_dev); +static void setgain(struct gspca_dev *gspca_dev); + /* V4L2 controls supported by the driver */ static struct ctrl sd_ctrls[] = { + { +#define BRIGHTNESS_IDX 0 + { + .id = V4L2_CID_BRIGHTNESS, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Brightness", + .minimum = MR97310A_BRIGHTNESS_MIN, + .maximum = MR97310A_BRIGHTNESS_MAX, + .step = 1, + .default_value = MR97310A_BRIGHTNESS_DEFAULT, + .flags = 0, + }, + .set = sd_setbrightness, + .get = sd_getbrightness, + }, + { +#define EXPOSURE_IDX 1 + { + .id = V4L2_CID_EXPOSURE, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Exposure", + .minimum = MR97310A_EXPOSURE_MIN, + .maximum = MR97310A_EXPOSURE_MAX, + .step = 1, + .default_value = MR97310A_EXPOSURE_DEFAULT, + .flags = 0, + }, + .set = sd_setexposure, + .get = sd_getexposure, + }, + { +#define GAIN_IDX 2 + { + .id = V4L2_CID_GAIN, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Gain", + .minimum = MR97310A_GAIN_MIN, + .maximum = MR97310A_GAIN_MAX, + .step = 1, + .default_value = MR97310A_GAIN_DEFAULT, + .flags = 0, + }, + .set = sd_setgain, + .get = sd_getgain, + }, }; static const struct v4l2_pix_format vga_mode[] = { @@ -65,7 +170,7 @@ static const struct v4l2_pix_format vga_mode[] = { }; /* the bytes to write are in gspca_dev->usb_buf */ -static int reg_w(struct gspca_dev *gspca_dev, int len) +static int mr_write(struct gspca_dev *gspca_dev, int len) { int rc; @@ -78,15 +183,249 @@ static int reg_w(struct gspca_dev *gspca_dev, int len) return rc; } +/* the bytes are read into gspca_dev->usb_buf */ +static int mr_read(struct gspca_dev *gspca_dev, int len) +{ + int rc; + + rc = usb_bulk_msg(gspca_dev->dev, + usb_rcvbulkpipe(gspca_dev->dev, 3), + gspca_dev->usb_buf, len, NULL, 500); + if (rc < 0) + PDEBUG(D_ERR, "reg read [%02x] error %d", + gspca_dev->usb_buf[0], rc); + return rc; +} + +static int sensor_write_reg(struct gspca_dev *gspca_dev, u8 reg, u8 flags, + const u8 *data, int len) +{ + gspca_dev->usb_buf[0] = 0x1f; + gspca_dev->usb_buf[1] = flags; + gspca_dev->usb_buf[2] = reg; + memcpy(gspca_dev->usb_buf + 3, data, len); + + return mr_write(gspca_dev, len + 3); +} + +static int sensor_write_regs(struct gspca_dev *gspca_dev, + const struct sensor_w_data *data, int len) +{ + int i, rc; + + for (i = 0; i < len; i++) { + rc = sensor_write_reg(gspca_dev, data[i].reg, data[i].flags, + data[i].data, data[i].len); + if (rc < 0) + return rc; + } + + return 0; +} + +static int sensor_write1(struct gspca_dev *gspca_dev, u8 reg, u8 data) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 buf, confirm_reg; + int rc; + + buf = data; + rc = sensor_write_reg(gspca_dev, reg, 0x01, &buf, 1); + if (rc < 0) + return rc; + + buf = 0x01; + confirm_reg = sd->sensor_type ? 0x13 : 0x11; + rc = sensor_write_reg(gspca_dev, confirm_reg, 0x00, &buf, 1); + if (rc < 0) + return rc; + + return 0; +} + +static int cam_get_response16(struct gspca_dev *gspca_dev) +{ + __u8 *data = gspca_dev->usb_buf; + int err_code; + + data[0] = 0x21; + err_code = mr_write(gspca_dev, 1); + if (err_code < 0) + return err_code; + + err_code = mr_read(gspca_dev, 16); + return err_code; +} + +static int zero_the_pointer(struct gspca_dev *gspca_dev) +{ + __u8 *data = gspca_dev->usb_buf; + int err_code; + u8 status = 0; + int tries = 0; + + err_code = cam_get_response16(gspca_dev); + if (err_code < 0) + return err_code; + + err_code = mr_write(gspca_dev, 1); + data[0] = 0x19; + data[1] = 0x51; + err_code = mr_write(gspca_dev, 2); + if (err_code < 0) + return err_code; + + err_code = cam_get_response16(gspca_dev); + if (err_code < 0) + return err_code; + + data[0] = 0x19; + data[1] = 0xba; + err_code = mr_write(gspca_dev, 2); + if (err_code < 0) + return err_code; + + err_code = cam_get_response16(gspca_dev); + if (err_code < 0) + return err_code; + + data[0] = 0x19; + data[1] = 0x00; + err_code = mr_write(gspca_dev, 2); + if (err_code < 0) + return err_code; + + err_code = cam_get_response16(gspca_dev); + if (err_code < 0) + return err_code; + + data[0] = 0x19; + data[1] = 0x00; + err_code = mr_write(gspca_dev, 2); + if (err_code < 0) + return err_code; + + while (status != 0x0a && tries < 256) { + err_code = cam_get_response16(gspca_dev); + status = data[0]; + tries++; + if (err_code < 0) + return err_code; + } + if (status != 0x0a) + PDEBUG(D_ERR, "status is %02x", status); + + tries = 0; + while (tries < 4) { + data[0] = 0x19; + data[1] = 0x00; + err_code = mr_write(gspca_dev, 2); + if (err_code < 0) + return err_code; + + err_code = cam_get_response16(gspca_dev); + status = data[0]; + tries++; + if (err_code < 0) + return err_code; + } + + data[0] = 0x19; + err_code = mr_write(gspca_dev, 1); + if (err_code < 0) + return err_code; + + err_code = mr_read(gspca_dev, 16); + if (err_code < 0) + return err_code; + + return 0; +} + +static u8 get_sensor_id(struct gspca_dev *gspca_dev) +{ + int err_code; + + gspca_dev->usb_buf[0] = 0x1e; + err_code = mr_write(gspca_dev, 1); + if (err_code < 0) + return err_code; + + err_code = mr_read(gspca_dev, 16); + if (err_code < 0) + return err_code; + + PDEBUG(D_PROBE, "Byte zero reported is %01x", gspca_dev->usb_buf[0]); + + return gspca_dev->usb_buf[0]; +} + /* this function is called at probe time */ static int sd_config(struct gspca_dev *gspca_dev, const struct usb_device_id *id) { + struct sd *sd = (struct sd *) gspca_dev; struct cam *cam; + __u8 *data = gspca_dev->usb_buf; + int err_code; cam = &gspca_dev->cam; cam->cam_mode = vga_mode; cam->nmodes = ARRAY_SIZE(vga_mode); + + if (id->idProduct == 0x010e) { + sd->cam_type = CAM_TYPE_CIF; + cam->nmodes--; + + data[0] = 0x01; + data[1] = 0x01; + err_code = mr_write(gspca_dev, 2); + if (err_code < 0) + return err_code; + + msleep(200); + data[0] = get_sensor_id(gspca_dev); + /* + * Known CIF cameras. If you have another to report, please do + * + * Name byte just read sd->sensor_type + * reported by + * Sakar Spy-shot 0x28 T. Kilgore 0 + * Innovage 0xf5 (unstable) T. Kilgore 0 + * Vivitar Mini 0x53 H. De Goede 0 + * Vivitar Mini 0x04 / 0x24 E. Rodriguez 0 + * Vivitar Mini 0x08 T. Kilgore 1 + * Elta-Media 8212dc 0x23 T. Kaiser 1 + * Philips dig. keych. 0x37 T. Kilgore 1 + */ + if ((data[0] & 0x78) == 8 || + ((data[0] & 0x2) == 0x2 && data[0] != 0x53)) + sd->sensor_type = 1; + else + sd->sensor_type = 0; + + PDEBUG(D_PROBE, "MR97310A CIF camera detected, sensor: %d", + sd->sensor_type); + + if (force_sensor_type != -1) { + sd->sensor_type = !! force_sensor_type; + PDEBUG(D_PROBE, "Forcing sensor type to: %d", + sd->sensor_type); + } + + if (sd->sensor_type == 0) + gspca_dev->ctrl_dis = (1 << BRIGHTNESS_IDX); + } else { + sd->cam_type = CAM_TYPE_VGA; + PDEBUG(D_PROBE, "MR97310A VGA camera detected"); + gspca_dev->ctrl_dis = (1 << BRIGHTNESS_IDX) | + (1 << EXPOSURE_IDX) | (1 << GAIN_IDX); + } + + sd->brightness = MR97310A_BRIGHTNESS_DEFAULT; + sd->exposure = MR97310A_EXPOSURE_DEFAULT; + sd->gain = MR97310A_GAIN_DEFAULT; + return 0; } @@ -96,183 +435,462 @@ static int sd_init(struct gspca_dev *gspca_dev) return 0; } -static int sd_start(struct gspca_dev *gspca_dev) +static int start_cif_cam(struct gspca_dev *gspca_dev) { struct sd *sd = (struct sd *) gspca_dev; __u8 *data = gspca_dev->usb_buf; int err_code; - - sd->sof_read = 0; - - /* Note: register descriptions guessed from MR97113A driver */ - + const __u8 startup_string[] = { + 0x00, + 0x0d, + 0x01, + 0x00, /* Hsize/8 for 352 or 320 */ + 0x00, /* Vsize/4 for 288 or 240 */ + 0x13, /* or 0xbb, depends on sensor */ + 0x00, /* Hstart, depends on res. */ + 0x00, /* reserved ? */ + 0x00, /* Vstart, depends on res. and sensor */ + 0x50, /* 0x54 to get 176 or 160 */ + 0xc0 + }; + + /* Note: Some of the above descriptions guessed from MR97113A driver */ data[0] = 0x01; data[1] = 0x01; - err_code = reg_w(gspca_dev, 2); + err_code = mr_write(gspca_dev, 2); if (err_code < 0) return err_code; - data[0] = 0x00; - data[1] = 0x0d; - data[2] = 0x01; - data[5] = 0x2b; - data[7] = 0x00; - data[9] = 0x50; /* reg 8, no scale down */ - data[10] = 0xc0; + memcpy(data, startup_string, 11); + if (sd->sensor_type) + data[5] = 0xbb; switch (gspca_dev->width) { case 160: - data[9] |= 0x0c; /* reg 8, 4:1 scale down */ + data[9] |= 0x04; /* reg 8, 2:1 scale down from 320 */ /* fall thru */ case 320: - data[9] |= 0x04; /* reg 8, 2:1 scale down */ - /* fall thru */ - case 640: default: - data[3] = 0x50; /* reg 2, H size */ - data[4] = 0x78; /* reg 3, V size */ - data[6] = 0x04; /* reg 5, H start */ - data[8] = 0x03; /* reg 7, V start */ + data[3] = 0x28; /* reg 2, H size/8 */ + data[4] = 0x3c; /* reg 3, V size/4 */ + data[6] = 0x14; /* reg 5, H start */ + data[8] = 0x1a + sd->sensor_type; /* reg 7, V start */ break; - case 176: - data[9] |= 0x04; /* reg 8, 2:1 scale down */ + data[9] |= 0x04; /* reg 8, 2:1 scale down from 352 */ /* fall thru */ case 352: - data[3] = 0x2c; /* reg 2, H size */ - data[4] = 0x48; /* reg 3, V size */ - data[6] = 0x94; /* reg 5, H start */ - data[8] = 0x63; /* reg 7, V start */ + data[3] = 0x2c; /* reg 2, H size/8 */ + data[4] = 0x48; /* reg 3, V size/4 */ + data[6] = 0x06; /* reg 5, H start */ + data[8] = 0x06 + sd->sensor_type; /* reg 7, V start */ break; } - - err_code = reg_w(gspca_dev, 11); + err_code = mr_write(gspca_dev, 11); if (err_code < 0) return err_code; - data[0] = 0x0a; - data[1] = 0x80; - err_code = reg_w(gspca_dev, 2); + if (!sd->sensor_type) { + const struct sensor_w_data cif_sensor0_init_data[] = { + {0x02, 0x00, {0x03, 0x5a, 0xb5, 0x01, + 0x0f, 0x14, 0x0f, 0x10}, 8}, + {0x0c, 0x00, {0x04, 0x01, 0x01, 0x00, 0x1f}, 5}, + {0x12, 0x00, {0x07}, 1}, + {0x1f, 0x00, {0x06}, 1}, + {0x27, 0x00, {0x04}, 1}, + {0x29, 0x00, {0x0c}, 1}, + {0x40, 0x00, {0x40, 0x00, 0x04}, 3}, + {0x50, 0x00, {0x60}, 1}, + {0x60, 0x00, {0x06}, 1}, + {0x6b, 0x00, {0x85, 0x85, 0xc8, 0xc8, 0xc8, 0xc8}, 6}, + {0x72, 0x00, {0x1e, 0x56}, 2}, + {0x75, 0x00, {0x58, 0x40, 0xa2, 0x02, 0x31, 0x02, + 0x31, 0x80, 0x00}, 9}, + {0x11, 0x00, {0x01}, 1}, + {0, 0, {0}, 0} + }; + err_code = sensor_write_regs(gspca_dev, cif_sensor0_init_data, + ARRAY_SIZE(cif_sensor0_init_data)); + } else { /* sd->sensor_type = 1 */ + const struct sensor_w_data cif_sensor1_init_data[] = { + /* Reg 3,4, 7,8 get set by the controls */ + {0x02, 0x00, {0x10}, 1}, + {0x05, 0x01, {0x22}, 1}, /* 5/6 also seen as 65h/32h */ + {0x06, 0x01, {0x00}, 1}, + {0x09, 0x02, {0x0e}, 1}, + {0x0a, 0x02, {0x05}, 1}, + {0x0b, 0x02, {0x05}, 1}, + {0x0c, 0x02, {0x0f}, 1}, + {0x0d, 0x02, {0x07}, 1}, + {0x0e, 0x02, {0x0c}, 1}, + {0x0f, 0x00, {0x00}, 1}, + {0x10, 0x00, {0x06}, 1}, + {0x11, 0x00, {0x07}, 1}, + {0x12, 0x00, {0x00}, 1}, + {0x13, 0x00, {0x01}, 1}, + {0, 0, {0}, 0} + }; + err_code = sensor_write_regs(gspca_dev, cif_sensor1_init_data, + ARRAY_SIZE(cif_sensor1_init_data)); + } if (err_code < 0) return err_code; - data[0] = 0x14; - data[1] = 0x0a; - err_code = reg_w(gspca_dev, 2); - if (err_code < 0) - return err_code; + setbrightness(gspca_dev); + setexposure(gspca_dev); + setgain(gspca_dev); - data[0] = 0x1b; - data[1] = 0x00; - err_code = reg_w(gspca_dev, 2); - if (err_code < 0) - return err_code; + msleep(200); - data[0] = 0x15; - data[1] = 0x16; - err_code = reg_w(gspca_dev, 2); + data[0] = 0x00; + data[1] = 0x4d; /* ISOC transfering enable... */ + err_code = mr_write(gspca_dev, 2); if (err_code < 0) return err_code; - data[0] = 0x16; - data[1] = 0x10; - err_code = reg_w(gspca_dev, 2); - if (err_code < 0) - return err_code; + return 0; +} - data[0] = 0x17; - data[1] = 0x3a; - err_code = reg_w(gspca_dev, 2); - if (err_code < 0) - return err_code; +static int start_vga_cam(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + __u8 *data = gspca_dev->usb_buf; + int err_code; + const __u8 startup_string[] = {0x00, 0x0d, 0x01, 0x00, 0x00, 0x2b, + 0x00, 0x00, 0x00, 0x50, 0xc0}; - data[0] = 0x18; - data[1] = 0x68; - err_code = reg_w(gspca_dev, 2); - if (err_code < 0) - return err_code; + /* What some of these mean is explained in start_cif_cam(), above */ + sd->sof_read = 0; - data[0] = 0x1f; - data[1] = 0x00; - data[2] = 0x02; - data[3] = 0x06; - data[4] = 0x59; - data[5] = 0x0c; - data[6] = 0x16; - data[7] = 0x00; - data[8] = 0x07; - data[9] = 0x00; - data[10] = 0x01; - err_code = reg_w(gspca_dev, 11); + /* + * We have to know which camera we have, because the register writes + * depend upon the camera. This test, run before we actually enter + * the initialization routine, distinguishes most of the cameras, If + * needed, another routine is done later, too. + */ + memset(data, 0, 16); + data[0] = 0x20; + err_code = mr_write(gspca_dev, 1); if (err_code < 0) return err_code; - data[0] = 0x1f; - data[1] = 0x04; - data[2] = 0x11; - data[3] = 0x01; - err_code = reg_w(gspca_dev, 4); + err_code = mr_read(gspca_dev, 16); if (err_code < 0) return err_code; - data[0] = 0x1f; - data[1] = 0x00; - data[2] = 0x0a; - data[3] = 0x00; - data[4] = 0x01; - data[5] = 0x00; - data[6] = 0x00; - data[7] = 0x01; - data[8] = 0x00; - data[9] = 0x0a; - err_code = reg_w(gspca_dev, 10); - if (err_code < 0) - return err_code; + PDEBUG(D_PROBE, "Byte reported is %02x", data[0]); + + msleep(200); + /* + * Known VGA cameras. If you have another to report, please do + * + * Name byte just read sd->sensor_type + * sd->do_lcd_stop + * Aiptek Pencam VGA+ 0x31 0 1 + * ION digital 0x31 0 1 + * Argus DC-1620 0x30 1 0 + * Argus QuickClix 0x30 1 1 (not caught here) + */ + sd->sensor_type = data[0] & 1; + sd->do_lcd_stop = (~data[0]) & 1; + + - data[0] = 0x1f; - data[1] = 0x04; - data[2] = 0x11; - data[3] = 0x01; - err_code = reg_w(gspca_dev, 4); + /* Streaming setup begins here. */ + + + data[0] = 0x01; + data[1] = 0x01; + err_code = mr_write(gspca_dev, 2); if (err_code < 0) return err_code; - data[0] = 0x1f; - data[1] = 0x00; - data[2] = 0x12; - data[3] = 0x00; - data[4] = 0x63; - data[5] = 0x00; - data[6] = 0x70; - data[7] = 0x00; - data[8] = 0x00; - err_code = reg_w(gspca_dev, 9); + /* + * A second test can now resolve any remaining ambiguity in the + * identification of the camera type, + */ + if (!sd->sensor_type) { + data[0] = get_sensor_id(gspca_dev); + if (data[0] == 0x7f) { + sd->sensor_type = 1; + PDEBUG(D_PROBE, "sensor_type corrected to 1"); + } + msleep(200); + } + + if (force_sensor_type != -1) { + sd->sensor_type = !! force_sensor_type; + PDEBUG(D_PROBE, "Forcing sensor type to: %d", + sd->sensor_type); + } + + /* + * Known VGA cameras. + * This test is only run if the previous test returned 0x30, but + * here is the information for all others, too, just for reference. + * + * Name byte just read sd->sensor_type + * + * Aiptek Pencam VGA+ 0xfb (this test not run) 1 + * ION digital 0xbd (this test not run) 1 + * Argus DC-1620 0xe5 (no change) 0 + * Argus QuickClix 0x7f (reclassified) 1 + */ + memcpy(data, startup_string, 11); + if (!sd->sensor_type) { + data[5] = 0x00; + data[10] = 0x91; + } + + switch (gspca_dev->width) { + case 160: + data[9] |= 0x0c; /* reg 8, 4:1 scale down */ + /* fall thru */ + case 320: + data[9] |= 0x04; /* reg 8, 2:1 scale down */ + /* fall thru */ + case 640: + default: + data[3] = 0x50; /* reg 2, H size/8 */ + data[4] = 0x78; /* reg 3, V size/4 */ + data[6] = 0x04; /* reg 5, H start */ + data[8] = 0x03; /* reg 7, V start */ + if (sd->do_lcd_stop) + data[8] = 0x04; /* Bayer tile shifted */ + break; + + case 176: + data[9] |= 0x04; /* reg 8, 2:1 scale down */ + /* fall thru */ + case 352: + data[3] = 0x2c; /* reg 2, H size */ + data[4] = 0x48; /* reg 3, V size */ + data[6] = 0x94; /* reg 5, H start */ + data[8] = 0x63; /* reg 7, V start */ + if (sd->do_lcd_stop) + data[8] = 0x64; /* Bayer tile shifted */ + break; + } + + err_code = mr_write(gspca_dev, 11); if (err_code < 0) return err_code; - data[0] = 0x1f; - data[1] = 0x04; - data[2] = 0x11; - data[3] = 0x01; - err_code = reg_w(gspca_dev, 4); + if (!sd->sensor_type) { + /* The only known sensor_type 0 cam is the Argus DC-1620 */ + const struct sensor_w_data vga_sensor0_init_data[] = { + {0x01, 0x00, {0x0c, 0x00, 0x04}, 3}, + {0x14, 0x00, {0x01, 0xe4, 0x02, 0x84}, 4}, + {0x20, 0x00, {0x00, 0x80, 0x00, 0x08}, 4}, + {0x25, 0x00, {0x03, 0xa9, 0x80}, 3}, + {0x30, 0x00, {0x30, 0x18, 0x10, 0x18}, 4}, + {0, 0, {0}, 0} + }; + err_code = sensor_write_regs(gspca_dev, vga_sensor0_init_data, + ARRAY_SIZE(vga_sensor0_init_data)); + } else { /* sd->sensor_type = 1 */ + const struct sensor_w_data vga_sensor1_init_data[] = { + {0x02, 0x00, {0x06, 0x59, 0x0c, 0x16, 0x00, + 0x07, 0x00, 0x01}, 8}, + {0x11, 0x04, {0x01}, 1}, + /*{0x0a, 0x00, {0x00, 0x01, 0x00, 0x00, 0x01, */ + {0x0a, 0x00, {0x01, 0x06, 0x00, 0x00, 0x01, + 0x00, 0x0a}, 7}, + {0x11, 0x04, {0x01}, 1}, + {0x12, 0x00, {0x00, 0x63, 0x00, 0x70, 0x00, 0x00}, 6}, + {0x11, 0x04, {0x01}, 1}, + {0, 0, {0}, 0} + }; + err_code = sensor_write_regs(gspca_dev, vga_sensor1_init_data, + ARRAY_SIZE(vga_sensor1_init_data)); + } if (err_code < 0) return err_code; + msleep(200); data[0] = 0x00; data[1] = 0x4d; /* ISOC transfering enable... */ - err_code = reg_w(gspca_dev, 2); + err_code = mr_write(gspca_dev, 2); + + return err_code; +} + +static int sd_start(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + int err_code; + struct cam *cam; + + cam = &gspca_dev->cam; + sd->sof_read = 0; + /* + * Some of the supported cameras require the memory pointer to be + * set to 0, or else they will not stream. + */ + zero_the_pointer(gspca_dev); + msleep(200); + if (sd->cam_type == CAM_TYPE_CIF) { + err_code = start_cif_cam(gspca_dev); + } else { + err_code = start_vga_cam(gspca_dev); + } return err_code; } static void sd_stopN(struct gspca_dev *gspca_dev) { + struct sd *sd = (struct sd *) gspca_dev; int result; gspca_dev->usb_buf[0] = 1; gspca_dev->usb_buf[1] = 0; - result = reg_w(gspca_dev, 2); + result = mr_write(gspca_dev, 2); if (result < 0) PDEBUG(D_ERR, "Camera Stop failed"); + + /* Not all the cams need this, but even if not, probably a good idea */ + zero_the_pointer(gspca_dev); + if (sd->do_lcd_stop) { + gspca_dev->usb_buf[0] = 0x19; + gspca_dev->usb_buf[1] = 0x54; + result = mr_write(gspca_dev, 2); + if (result < 0) + PDEBUG(D_ERR, "Camera Stop failed"); + } +} + +static void setbrightness(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 val; + + if (gspca_dev->ctrl_dis & (1 << BRIGHTNESS_IDX)) + return; + + /* Note register 7 is also seen as 0x8x or 0xCx in dumps */ + if (sd->brightness > 0) { + sensor_write1(gspca_dev, 7, 0x00); + val = sd->brightness; + } else { + sensor_write1(gspca_dev, 7, 0x01); + val = 257 - sd->brightness; + } + sensor_write1(gspca_dev, 8, val); +} + +static void setexposure(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + u8 val; + + if (gspca_dev->ctrl_dis & (1 << EXPOSURE_IDX)) + return; + + if (sd->sensor_type) { + val = sd->exposure >> 4; + sensor_write1(gspca_dev, 3, val); + val = sd->exposure & 0xf; + sensor_write1(gspca_dev, 4, val); + } else { + u8 clockdiv; + int exposure; + + /* We have both a clock divider and an exposure register. + We first calculate the clock divider, as that determines + the maximum exposure and then we calculayte the exposure + register setting (which goes from 0 - 511). + + Note our 0 - 4095 exposure is mapped to 0 - 511 + milliseconds exposure time */ + clockdiv = (60 * sd->exposure + 7999) / 8000; + + /* Limit framerate to not exceed usb bandwidth */ + if (clockdiv < 3 && gspca_dev->width >= 320) + clockdiv = 3; + else if (clockdiv < 2) + clockdiv = 2; + + /* Frame exposure time in ms = 1000 * clockdiv / 60 -> + exposure = (sd->exposure / 8) * 511 / (1000 * clockdiv / 60) */ + exposure = (60 * 511 * sd->exposure) / (8000 * clockdiv); + if (exposure > 511) + exposure = 511; + + /* exposure register value is reversed! */ + exposure = 511 - exposure; + + sensor_write1(gspca_dev, 0x02, clockdiv); + sensor_write1(gspca_dev, 0x0e, exposure & 0xff); + sensor_write1(gspca_dev, 0x0f, exposure >> 8); + } +} + +static void setgain(struct gspca_dev *gspca_dev) +{ + struct sd *sd = (struct sd *) gspca_dev; + + if (gspca_dev->ctrl_dis & (1 << GAIN_IDX)) + return; + + if (sd->sensor_type) { + sensor_write1(gspca_dev, 0x0e, sd->gain); + } else { + sensor_write1(gspca_dev, 0x10, sd->gain); + } +} + +static int sd_setbrightness(struct gspca_dev *gspca_dev, __s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->brightness = val; + if (gspca_dev->streaming) + setbrightness(gspca_dev); + return 0; +} + +static int sd_getbrightness(struct gspca_dev *gspca_dev, __s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + *val = sd->brightness; + return 0; +} + +static int sd_setexposure(struct gspca_dev *gspca_dev, __s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->exposure = val; + if (gspca_dev->streaming) + setexposure(gspca_dev); + return 0; +} + +static int sd_getexposure(struct gspca_dev *gspca_dev, __s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + *val = sd->exposure; + return 0; +} + +static int sd_setgain(struct gspca_dev *gspca_dev, __s32 val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + sd->gain = val; + if (gspca_dev->streaming) + setgain(gspca_dev); + return 0; +} + +static int sd_getgain(struct gspca_dev *gspca_dev, __s32 *val) +{ + struct sd *sd = (struct sd *) gspca_dev; + + *val = sd->gain; + return 0; } /* Include pac common sof detection functions */ @@ -320,8 +938,9 @@ static const struct sd_desc sd_desc = { /* -- module initialisation -- */ static const __devinitdata struct usb_device_id device_table[] = { - {USB_DEVICE(0x08ca, 0x0111)}, - {USB_DEVICE(0x093a, 0x010f)}, + {USB_DEVICE(0x08ca, 0x0111)}, /* Aiptek Pencam VGA+ */ + {USB_DEVICE(0x093a, 0x010f)}, /* All other known MR97310A VGA cams */ + {USB_DEVICE(0x093a, 0x010e)}, /* All known MR97310A CIF cams */ {} }; MODULE_DEVICE_TABLE(usb, device_table); diff --git a/linux/drivers/media/video/gspca/pac207.c b/linux/drivers/media/video/gspca/pac207.c index 95a97ab68..96659433d 100644 --- a/linux/drivers/media/video/gspca/pac207.c +++ b/linux/drivers/media/video/gspca/pac207.c @@ -35,25 +35,17 @@ MODULE_LICENSE("GPL"); #define PAC207_BRIGHTNESS_MIN 0 #define PAC207_BRIGHTNESS_MAX 255 -#define PAC207_BRIGHTNESS_DEFAULT 4 /* power on default: 4 */ - -/* An exposure value of 4 also works (3 does not) but then we need to lower - the compression balance setting when in 352x288 mode, otherwise the usb - bandwidth is not enough and packets get dropped resulting in corrupt - frames. The problem with this is that when the compression balance gets - lowered below 0x80, the pac207 starts using a different compression - algorithm for some lines, these lines get prefixed with a 0x2dd2 prefix - and currently we do not know how to decompress these lines, so for now - we use a minimum exposure value of 5 */ -#define PAC207_EXPOSURE_MIN 5 +#define PAC207_BRIGHTNESS_DEFAULT 46 + +#define PAC207_EXPOSURE_MIN 3 #define PAC207_EXPOSURE_MAX 26 -#define PAC207_EXPOSURE_DEFAULT 5 /* power on default: 3 ?? */ -#define PAC207_EXPOSURE_KNEE 11 /* 4 = 30 fps, 11 = 8, 15 = 6 */ +#define PAC207_EXPOSURE_DEFAULT 5 /* power on default: 3 */ +#define PAC207_EXPOSURE_KNEE 8 /* 4 = 30 fps, 11 = 8, 15 = 6 */ #define PAC207_GAIN_MIN 0 #define PAC207_GAIN_MAX 31 #define PAC207_GAIN_DEFAULT 9 /* power on default: 9 */ -#define PAC207_GAIN_KNEE 20 +#define PAC207_GAIN_KNEE 31 #define PAC207_AUTOGAIN_DEADZONE 30 @@ -166,16 +158,12 @@ static const struct v4l2_pix_format sif_mode[] = { }; static const __u8 pac207_sensor_init[][8] = { - {0x10, 0x12, 0x0d, 0x12, 0x0c, 0x01, 0x29, 0xf0}, - {0x00, 0x64, 0x64, 0x64, 0x04, 0x10, 0xf0, 0x30}, + {0x10, 0x12, 0x0d, 0x12, 0x0c, 0x01, 0x29, 0x84}, + {0x49, 0x64, 0x64, 0x64, 0x04, 0x10, 0xf0, 0x30}, {0x00, 0x00, 0x00, 0x70, 0xa0, 0xf8, 0x00, 0x00}, - {0x00, 0x00, 0x32, 0x00, 0x96, 0x00, 0xa2, 0x02}, {0x32, 0x00, 0x96, 0x00, 0xA2, 0x02, 0xaf, 0x00}, }; - /* 48 reg_72 Rate Control end BalSize_4a =0x36 */ -static const __u8 PacReg72[] = { 0x00, 0x00, 0x36, 0x00 }; - static int pac207_write_regs(struct gspca_dev *gspca_dev, u16 index, const u8 *buffer, u16 length) { @@ -274,7 +262,6 @@ static int sd_init(struct gspca_dev *gspca_dev) * Bit_1=LED, * Bit_2=Compression test mode enable */ pac207_write_reg(gspca_dev, 0x0f, 0x00); /* Power Control */ - pac207_write_reg(gspca_dev, 0x11, 0x30); /* Analog Bias */ return 0; } @@ -289,15 +276,13 @@ static int sd_start(struct gspca_dev *gspca_dev) pac207_write_regs(gspca_dev, 0x0002, pac207_sensor_init[0], 8); pac207_write_regs(gspca_dev, 0x000a, pac207_sensor_init[1], 8); pac207_write_regs(gspca_dev, 0x0012, pac207_sensor_init[2], 8); - pac207_write_regs(gspca_dev, 0x0040, pac207_sensor_init[3], 8); - pac207_write_regs(gspca_dev, 0x0042, pac207_sensor_init[4], 8); - pac207_write_regs(gspca_dev, 0x0048, PacReg72, 4); + pac207_write_regs(gspca_dev, 0x0042, pac207_sensor_init[3], 8); /* Compression Balance */ if (gspca_dev->width == 176) pac207_write_reg(gspca_dev, 0x4a, 0xff); else - pac207_write_reg(gspca_dev, 0x4a, 0x88); + pac207_write_reg(gspca_dev, 0x4a, 0x30); pac207_write_reg(gspca_dev, 0x4b, 0x00); /* Sram test value */ pac207_write_reg(gspca_dev, 0x08, sd->brightness); @@ -346,7 +331,7 @@ static void pac207_do_auto_gain(struct gspca_dev *gspca_dev) if (sd->autogain_ignore_frames > 0) sd->autogain_ignore_frames--; else if (gspca_auto_gain_n_exposure(gspca_dev, avg_lum, - 100 + sd->brightness / 2, PAC207_AUTOGAIN_DEADZONE, + 100, PAC207_AUTOGAIN_DEADZONE, PAC207_GAIN_KNEE, PAC207_EXPOSURE_KNEE)) sd->autogain_ignore_frames = PAC_AUTOGAIN_IGNORE_FRAMES; } diff --git a/linux/drivers/media/video/vino.c b/linux/drivers/media/video/vino.c index 8383e6f80..5a8dd5e19 100644 --- a/linux/drivers/media/video/vino.c +++ b/linux/drivers/media/video/vino.c @@ -50,6 +50,7 @@ #include <asm/sgi/ip22.h> #include <asm/sgi/mc.h> +#include "compat.h" #include "vino.h" #include "saa7191.h" #include "indycam.h" diff --git a/linux/include/linux/videodev2.h b/linux/include/linux/videodev2.h index 6fc44b733..9d61bae27 100644 --- a/linux/include/linux/videodev2.h +++ b/linux/include/linux/videodev2.h @@ -375,6 +375,7 @@ struct v4l2_fmtdesc { }; #define V4L2_FMT_FLAG_COMPRESSED 0x0001 +#define V4L2_FMT_FLAG_EMULATED 0x0002 #if 1 /*KEEP*/ /* Experimental Frame Size and frame rate enumeration */ |