| Age | Commit message (Collapse) | Author |
|---|
|
From: Frej Drejhammar <frej.drejhammar@gmail.com>
Define a pre-defined control ID for color killer functionality.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Frej Drejhammar <frej.drejhammar@gmail.com>
An enabled chroma AGC will not degrade picture quality if enabled on a
color PAL or NTSC signal with nominal signal levels. It will give a
significant color reproduction improvement if the chroma signals
diverge from nominal levels. Therefore enable chroma AGC by default
for PAL and NTSC standards.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Frej Drejhammar <frej.drejhammar@gmail.com>
The cx2388x family has support for chroma AGC. This patch implements a
the V4L2_CID_CHROMA_AGC control for the cx2388x family. By default
chroma AGC is disabled, as in previous versions of the driver.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Frej Drejhammar <frej.drejhammar@gmail.com>
Define a pre-defined control ID for chroma automatic gain control.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Marton Balint <cus@fazekas.hu>
If the IR worker is not stopped before the removal of the cx88xx module,
an OOPS may occur, because the worker function cx88_ir_work gets called.
So stop the ir worker.
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
This board has a s5h1409 demod, plus a xc30x8 tuner (probably, xc3018).
This patch adds proper support for radio, video, s-video, composite and ATSC.
However, support for radio and video depends on having s5h1409 i2c gate open,
otherwise, xc30x8 chip won't be visible.
For a better support, some rework is needed on cx88 driver, to allow adding
xc30x8 to i2c bus without sending i2c 0 byte reading to 0xc2 address.
Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com> for helping to figure
out the proper parameters for s5h1409 and the GPIO pins used by each
configuration.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mike Isely <isely@pobox.com>
Fix use of a non-int (size_t) being passed in a printf width field.
This benign issue has apparently been around for a long time, but went
undetected until now.
Signed-off-by: Mike Isely <isely@pobox.com>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
kernel-sync:
Some merge error happened with those hunks. Merge them with mainstream, since
the check for GENERIC_GPIO are happening twice. Those seems to be wrong.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
kernel-sync:
Original description:
Author: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Date: Sun Nov 4 00:50:19 2007 -0400
V4L/DVB: Don't access input_dev->private directly
Drivers should use input_{get|set}_drvdata() instead of accessing
input_dev->provate directly, but since these drivers do not actually
use the data stored there we can simply remove the assignments.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Those files are maintained on other trees. Just update them to the newest
version.
kernel-sync:
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
kernel-sync:
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Update Kconfig for the hybrid devices recently converted
to use tuner-simple rather than dvb-pll.
dvb-bt8xx no longer uses dvb-pll at all, so remove all
references to dvb-pll within that driver.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Fix the following build error:
In file included from dvb-bt8xx.c:35:
dvb-bt8xx.h:42:26: error: tuner-simple.h: No such file or directory
dvb-bt8xx.c: In function 'frontend_init':
dvb-bt8xx.c:612: error: 'simple_tuner_attach' undeclared (first use in this function)
dvb-bt8xx.c:612: error: (Each undeclared identifier is reported only once
dvb-bt8xx.c:612: error: for each function it appears in.)
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of '__a'
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:612: warning: cast from pointer to integer of different size
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:612: warning: cast from pointer to integer of different size
dvb-bt8xx.c:612: error: called object '__a' is not a function
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of '__a'
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:696: warning: cast from pointer to integer of different size
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:696: warning: cast from pointer to integer of different size
dvb-bt8xx.c:696: error: called object '__a' is not a function
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
There are a number of different firmware versions and variants, shipped
together with boards.
This patch adds an extra parameter to the tuner-xc2028 to allow specifying for
an specific firmware name to be loaded. This helps to test for a firmware that
better fits some board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
The ability to select RF input was a supported feature only available on
Philips TUV1236d and Philips FCV1236d.
This feature, along with support for the tuners that used it,
was moved into the tuner-simple module.
This can now be removed from dvb-pll.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
In case of muliple cameras, handled by the same driver, they can support
different picture formats, therefore formats and num_formats cannot belong
to soc_camera_ops, which is only one per driver, move them to
soc_camera_device, which is one per device instance. OTOH, probe and
remove methods are always the same, move them to soc_camera_ops.
Thanks to Eric Miao for making me look at this code again:-)
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Douglas Schilling Landgraf <dougsland@gmail.com>
Removed unnecessary VIDIOC_G_PRIORITY validation.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
|
|
From: Douglas Schilling Landgraf <dougsland@gmail.com>
Added macro CONFIG_COMPAT for v4l_compat_ioctl32.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Force the main pll charge pump or cal pll charge pump to source current
to the main pll loop filter or cal pll loop filter, respectively.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Tobias Lorenz <tobias.lorenz@gmx.net>
this patch fixes several kernel oops, when unplugging device while it is in use:
Basically the patch delays freeing of the internal variables in si470x_usb_driver_disconnect,
until the the last user closed the device in si470x_fops_release.
This was implemented a while ago with the help of Oliver Neukum.
I tested the patch five times (unplugging while in use) without oops coming from the radio-si470x driver anymore.
A remaining oops was coming from the usbaudio driver, but this is someone else task.
Hopefully this fixed all unplugging issues.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Set rfagc to high speed mode before setting the pll.
Set rfagc to normal speed mode at the end of the function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
allow device-specific configuration of rf agc rf top and if top
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
The internal calibration signal must be set on the cal pll.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Both the tda18271 c1 and c2 parts only need EP3 through MD3 to be written for
the image rejection calibration's low band initialization.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
remove #if 0'd support for:
Philips TUV1236D
Philips TD1316
Philips FMD1216ME
LG TDVS-H06xF
Philips FCV1236D
Thomson FE6600
Microtune 4042 FI5
Thomson dtt761x
Support for these tuners has been moved into the 'tuner-simple' module.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The video_dev parameter, on tuner-xc2028 were used to pass i2c private data to
tuner_callback. Since the driver already have a pointer to i2c_adap->algo_data,
uses this instead.
This parameter were used also as a magic number to idenfity if two drivers are
trying to register the same xc3028 tuner. This occurs with boards with DVB
support, where both DVB and V4L drivers will share the same tuner.
Instead of using the algo_data as a private number, after this patch, the
driver will use i2c_adap->dev, with seems more consistent.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds a consistency check to avoid OOPS, if tuner_callback priv argument is
NULL. Also, simplifies callback codes on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
The pointer transferred directly points to the saa7134_dev
structure
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
The ISL6405 LNB supply is used on several Creatix / Medion cards. But only
the MD8800 needs its second section. So don't start it unless it is needed.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Alan McIvor <alan.mcivor@reveal.co.nz>
This patch fixes reported problems when trying to add a 9th device into a
system.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Andrew Morton <akpm@linux-foundation.org>
drivers/media/video/bt8xx/bttv-cards.c:3030:38: warning: "/*" within comment
drivers/media/video/bt8xx/bttv-cards.c:3032:20: warning: "/*" within comment
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
If left in blank, the driver will use value 0 (Temic PAL)
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner addresses were incorrect. Fix the entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
All standard related configuration is stored within
struct tda18271_std_map_item. Pass a pointer to this
structure rather than its individual members.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Tuner refactoring broke support of tuners with LNA configurations 1 and 2
for both, analog TV and DVB-T.
Additionally, this patch initializes the saa713x gpios defined by the gpiomask
at driver init to avoid undefined stated at dvb.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
