| Age | Commit message (Collapse) | Author |
|---|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes a few troubles on nxt200x implementation:
1) A nxt200x internal input control logic were done on both
cx88-dvb and saa7134-dvb;
2) The nx200x_set_pll_input callback were filling buffer, at the
5th position, without even testing if that buffer were filled;
3) a 5 byte buffer were written to the device, even if the
buffer were not properly initialized by calc_regs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The dvb-pll sleep function could only send a 2-byte sequence to the PLL.
This isn't enough in some cases, for example fmd1216me will need to send
a 4-byte command to set both BB and AB to the correct values.
Instead of using a fake band with a frequency of 0 to store the sleep
data (which has room for only two bytes), the new sleep function works
like the init function. A new pointer is added to the pll description,
and when non-NULL points to a buffer with the length and data to send.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
The IF frequency was specified for each band, but it's not something that
changes from band to band. None of the tuner definitions had a different
IF frequency (called offset) from one band to another.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
Some PLLs had one half the step size added to the offset, so that the
divisor would be rounded to the nearest integer. Some didn't and so
would always be rounded down.
This makes dvb-pll round to the nearest when calculating the divisor,
without the offset needing to be fudged. PLLs that had a fudged offset
have the offset changed to be just the IF frequency.
The satellite PLL dvb_pll_philips_sd1878_tda8261 was rounding up for some
reason, and I've kept it that way.
In addition, frequencies that were rounded to the nearest kHz are
extended to full Hz resolution. One sixth MHz step sizes that were
listed as 166,666 Hz are changed to 166,667 Hz, which is slightly closer.
PLLs that were already rounding:
dvb_pll_tda665x, offset was 36 1/6 (to nearest kHz) + step/2
dvb_pll_fmd1216me, offset was 36 1/8 (to two digits) + step/2
dvb_pll_thomson_fe6600, offset was 36 1/8 (to two digits) + step/2
dvb_pll_env57h1xd5, offset was 36 1/8 + step
Note that the last PLL, dvb_pll_env57h1xd5, appears to have had a bug in
the offset. Rather than adding stepsize/2, it was adding a full
stepsize. The PLL definition originally came from the dibusb driver,
which used 36 1/8 + step/2. The change to 36 1/8 + step was probably a
mistake added when the tuner was converted to dvb-pll.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Pierre Willenbrock <pierre@pirsoft.de>
Add support for Anubis Electronics "Lifeview" (USB-ID: 0x10fd:0x1513)
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
The struct tda1004x_config has a new entry: .ts_mode
Possible values are TDA10046_TS_PARALLEL or TDA10046_TS_SERIAL
There always is only one interface active, default is parallel.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Pierre Willenbrock <pierre@pirsoft.dnsalias.org>
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.dnsalias.org>
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Aapo Tahkola <aet@rasterburn.org>
This function should work for all m920x-based devices.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Oliver Endriss <o.endriss@gmx.de>
Fix bug introduced during infrared refactoring.
Thanks to Johann Friedrichs for spotting this.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Thanks-to: Johann Friedrichs <johann.friedrichs@web.de>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Change a 00 to just 0
Detect zero-length I2C messages and return not supported. I think I know
how to send one, but the problem is getting the slave's ack. The only
point of a zero-length message is for probing; too see if the slave will
ack its address. Since we don't know how to get the ack, we can't
support zero-length messages in a useful way, so it's probably best to
just return not supported for them.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Simon Arlott <simon@fire.lp0.eu>
Fix several instances of dvb-core functions using mutex_lock_interruptible
and returning -ERESTARTSYS where the calling function will either never
retry or never check the return value.
These cause a race condition with dvb_dmxdev_filter_free and
dvb_dvr_release, both of which are filesystem release functions whose
return value is ignored and will never be retried. When this happens it
becomes impossible to open dvr0 again (-EBUSY) since it has not been
released properly.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Write some better documentation about what might be known about how the
m920x I2C works, since a datasheet is lacking.
The I2C xfer function should now handle more types of I2C transactions
than it could before. Those it can't, will return error codes instead of
being executed incorrectly. Multi-byte reads were not being done
correctly, which should be fixed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Aapo Tahkola <aet@rasterburn.org>
- r/w bit is not part of the i2c address
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Aapo Tahkola <aet@rasterburn.org>
- Implement m920x i2c as suggested by Pierre Willenbrock
- remove "magic" hack
- r/w bit is not part of the i2c address
- move hardware remarks to header file
CC: Pierre Willenbrock <pierre@pirsoft.dnsalias.org>
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Oliver Endriss <o.endriss@gmx.de>
In transfer/replay mode the frontend lock status was never updated.
This caused a 'black screen' if VDR switched from transfer mode to
live mode on the same transponder.
Thanks to Marco Schluessler for spotting the problem.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
The code the i2c transactions was leftover from the old V4L-based ATSC
driver. It did too little with too much code. It is re-written to
remove unnecessary parameters and be more efficient. A demod register
can now be read with one function call, instead of repeating a dozen line
block of code each time.
There were msleep()'s, which appear to be unnecessary, spread around all
the I2C transactions. These have been removed. Reading SNR used to take
about 130 ms, now it's down to 1.8 ms.
Reads from the demodulator's registers do not return correct results
sometimes. Adding or removing the delays in the I2C transactions did not
appear to effect the probability of failure. If anything, the
transactions without delays were less likely to fail, but since far more
transactions could be made per second the number of failures per hour was
greater.
To increase reliability, the SNR and get_params functions will now retry
once if they get bad data back. This appears to have reduced the
probability of failure to effectively zero.
Some error messages are cleaned up or given KERN_* levels when they were
missing.
or51132_setmode() wasn't returning correct error codes, which is fixed as
well.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
CC: Rusty Scott <rustys@ieee.org>
|
|
From: Dennis Ranke <mail@exoticorn.de>
When trying to use a Hauppauge Nova-T Stick on a big-endian architecture
(such as powerpc) no frontend can be attached.
The attached patch fixes this problem by removing two lines in
dib0700_ctrl_rd() that try to correct the endianess on two values that
already are correct:
- /* think about swapping here */
- value = le16_to_cpu(value);
- index = le16_to_cpu(index);
With this simple patch this dvb hardware works great, thanks to anyone
involved for the good work. :)
Signed-off-by: Dennis Ranke <mail@exoticorn.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
The code of the dvb-pll driver and the lgh06xf driver is nearly
identical. The main difference is that the lgh06xf driver would set the
AGC TOP value on every tune call. The dvb-pll driver now has the ability
to set the AGC TOP when the front-end device is opened, which is a better
way to go about it. By using this ability of dvb-pll, the lgh06xf driver
is made unnecessary.
There is one other difference. dvb-pll will probe for the presence of an
I2C pll chip by doing a one byte read, the lgh06xf driver did not do
this. In some devices the PLL is not reachable over I2C at the timer the
tuner is attached. Some more initialization, such as firmware loading,
must take place first. None of the devices using a LG-H06xF should have
this problem.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Some tuners need or benefit from initialization, to change certain
settings from their power on default values.
Typically, tuners with TUA603x PLLs can benefit from setting the AGC TOP
value to something else. This patch includes code to set the AGC TOP to
103 dBuV for the Thomson DTT-761x tuners, which I have experimentally
verified gives the best SNR readings, increasing SNR by about 0.19 dB
over the default value.
Other tuners can make use of this as well. For example, the separate LG
TDVS-H06xF driver's only difference from dvb-pll is this same setting of
AGC TOP value.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
A number of drivers selected DVB_PLL when they did not need it, and some
that did need it did not select it.
The DVB_PLL option is given a name and help text, so that it will show up
in the config menu. DVB_PLL support can be turned on if an out-of-tree
driver needs it.
The standard dvb fe customization support is added to dvb-pll.h. Since
all modules which select DVB_PLL do so unconditionally, it is not
possible to turn dvb-pll off when an enabled module selects it, unlike
most of the other frontend/tuner drivers. This is because the users of
dvb-pll have static references to dvb-pll symbols other than the attach
function. If these references are removed, then dvb-pll will be
disablable as the other frontend/tuner drivers are.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Better to use sizeof() to get the size of the output buffer for the tuner
name, instead of just hard coding 128.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
- The i2c data buffer in tda827xa_set_params was 1 byte too short
- saa7134-dvb now gives an error mesage if tda827x could not be attached
- coding style fix in tda1004x.c
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Oliver Endriss <o.endriss@gmx.de>
Support for MSC_RAW and MSC_SCAN remote control events.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
From: Oliver Endriss <o.endriss@gmx.de>
Fix compilation error introduced by changeset 6d08d71cbcfb.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
From: David Härdeman <david@hardeman.nu>
The attached patch contains the last set of changes to the budget-ci IR
handling which makes it use the repeat handling of the input subsystem.
This allows some code simplification, makes sure that repeat key presses
are reported as such and also allows the "debounce" hack to be removed
altogether.
In addition a couple of static variables were removed which would have
confused the IR code if more than one card is used.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
From: Oliver Endriss <o.endriss@gmx.de>
Infrared remote control support rewritten.
Now each device provides its own event device, keymap, protocol,
inversion and address setting.
EVIOCGKEYCODE and EVIOCSKEYCODE ioctls are supported to read/modify
a keymap. Keymaps may be loaded using
- input tools (keyb etc.)
- av7110_loadkeys (obsolete, for backward compatibility)
New command line parameters:
- ir_protocol: select infrared protocol: 0 RC5, 1 RCMM (default)
- ir_inversion: signal inversion: 0 not inverted (default), 1 inverted
- ir_device_mask: bitmask of infrared devices (default: accept all)
Those parameters may be set anytime.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The cx23415 adds some extra features that this DVB decoding API did
not support. This API has been expanded to support the required
features. Both source and binary backwards compatibility is kept
intact by these changes. So existing applications are not affected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
|
From: Christophe Cattelain <xof@skynet.be>
Added USB_PID_PCTV_450E to the 'usb_device_id ttusb2_table' and an entry in the
.devices table. The 400e driver now supports the 'Pinnacle PCTV Sat Pro USB
(450e)' with USB_ID 2304:0222.
Signed-off-by: Christophe Cattelain <xof@skynet.be>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
dvb-pll normally opens the i2c gate before attempting to communicate with
the pll, but the code for this device is not using dvb-pll. This should
be cleaned up in the future, but for now, just open the i2c gate at the
appropriate place in order to fix this driver bug.
Thanks-to: Alex Woods <linux-dvb@giblets.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
kernel-sync:
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Backport changeset from Jean Delvare <khali@linux-fr.org> that declare
i2c_adapter parent devices.
kernel-sync:
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Backport a changeset from Schmielau <tim@physik3.uni-rostock.de> that
removes uneeded includes for linux/sched.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Jin-Bong lee <jinbong.lee@samsung.com>
Without this patch, the device will not be detected after firmware download
on big endian systems.
Signed-off-by: Jin-Bong lee <jinbong.lee@samsung.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Compat.h used to have an argument, now it doesn't. There was also some code:
if (current->flags & PF_FREEZE) { refrigerator(PF_FREEZE); }
which is the same as try_to_freeze(), and so can be replaced by it.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Hartmut Birr <e9hack@googlemail.com>
Enable BER/UNC counting for the stv0297 frontend.
The idea for this patch comes from stv0297_cs.c.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
|
