| Age | Commit message (Collapse) | Author |
|---|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The init callback was used in several places to load firmware. Make a separate
load_fw callback for that. This makes the code a lot more understandable.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The audio and vbi parts still used an 'ioctl'-like interface. Replace this
with normal functions.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CC: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
This change only affects comments.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Give messages originating from internal subdevs a header using the subdev's
name. Fixed an uninitialized variable problem with reading the EEPROM, noticed
from log output. Got rid of the unused cx18_av_exit() function.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
This is a major perturbation to cx18 I2C device handling to convert it to the
v4l2_device/subdeivce framework. This change breaks GPIO audio multiplexer
control for the time being. It will be fixed in a coming change.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Added a new chip identifer to v4l2-chip-ident for the integrated A/V broadcast
decoder core internal to the CX23418. Completed separation and encapsulation
of the A/V decoder core interface as a v4l2_subdevice. The cx18 driver now
compiles and links again.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
This is the next step in converting the cx18 driver to use the v4l2_device/
v4l2_subdevice framework. This is a straightforward conversion of the
cx18_av_*[ch] files. It compiles, but leaves the driver in an unlinkable
state at the moment.
Note, the cx18 integrated A/V digitizer will now make a host match at address 1,
as far as v4l2-dbg is concerned. That means it identifies itself as a separate
"chip", and acts as an alias to the integrated A/V decoder registers that are
also available with the host match at address 0.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Sliced VBI, in the manner that ivtv implements it as a separate data stream,
now works for 525 line 60 Hz systems like NTSC-M. It may work for 625 line
50 Hz systems, but I have more engineering work to do, to verify it is operating
properly. Sliced data insertion into the MPEG PS should be working, but is
untested.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
Add copyright attribution for files modified by awalls in 2008
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
cx18: Streamline cx18-io[ch] wrappers and enforce MMIO retry strategy so that
write retries always occur and read retries never occur (as they never help).
Remove MMIO statistics logging to speed up MMIO accesses. Deprecate & ignore
retry_mmio and mmio_ndelay module parameters, to essentially force
retry_mmio=1 and mmio_ndelay=0.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
cx18: Fix write retries for registers that always change - part 3.
Fix the io for the rest of the registers that will often not read back the
value just written. Modified register readback checks to make sure the
intended effect was achieved without constantly rewriting the registers.
The one outstanding register remaining is 0xc72014 CX18_AUDIO_ENABLE, whose
behavior on writes I have yet to determine.
Priority: normal
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Andy Walls <awalls@radix.net>
cx18: Add default behavior of checking and retrying PCI MMIO accesses.
The concept of checking and retrying PCI MMIO accesses for better reliability
in older motherboards was suggested by Steve Toth <stoth@linuxtv.org>. This
change implements MMIO retries and the retry_mmio module parameter that is
enabled by default. Limited experiments have shown this is more reliable than
the mmio_ndelay parameter. mmio_ndelay has insignificant effect with retries
enabled.
Priority: high
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Same issue as for cx25840: this function sets up the standard timings
and has nothing to do with VBI setup.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
For several MPEG controls and the volume control the default as returned
by VIDIOC_QUERYCTRL was incorrect and did not match the actual initial
value.
This is now fixed for cx18 and ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Reverted the 'Fix unintended auto configurations in cx18-av-core' patch,
instead disable the auto config completely.
Fix a bug in cx18_av_vbi_setup() where the standard tests were done
in the wrong order.
Tested with NTSC-M, PAL-BG, PAL-I, PAL-DK, PAL-M, PAL-Nc, SECAM-DK,
SECAM-L and SECAM-BG. The last one does not work at the moment due to
a tda9887.c bug.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Andy Walls <awalls@radix.net>
Change the cx18-av-core code so that accesses to cx23418 av core that
cause auto-configuration will be adjusted to emulate the auto-configuration
behavior of the cx25843. This fixes the VBI displayed as video at the top of
the frame for NTSC and probably other things.
Signed-off-by: Andy Walls <awalls@radix.net>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
The S-Video LUMA input was restricted to the In1-In4 inputs, but it
turns out that it can use the full range of In1-In8.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Many thanks to Steve Toth from Hauppauge and Nattu Dakshinamurthy from
Conexant for their support. I am in particular thankful to Hauppauge
since without their help this driver would not exist. It should also
be noted that Steve did the work to get the DVB part up and running.
Thank you!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: G. Andrew Walls <awalls@radix.net>
|
