| Age | Commit message (Collapse) | Author |
|---|
|
From: Michael Krufky <mkrufky@linuxtv.org>
We should not mute the audio input when we stop the codec,
because it will interfere with the live uncompressed stream.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Jelle Foks <jelle@foks.8m.com>
|
|
From: Ricardo Cerqueira <v4l@cerqueira.org>
Fix lack of audio on the MPEG-2 stream of wm8775 based blackbirds.
The wm8775 module initializes the audio input at "route 2", which doesn't
hold true for all boards. The HVR-1300, for example, uses route 1 for
tuner audio, and route 2 for baseband. So we must route the audio to the
proper input depending on what video input is being used.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Jelle Foks <jelle@foks.8m.com>
Remove the unnecessary BLACKBIRD_UNMUTE calls to the mpeg encoder in
cx88-blackbird.c
The encoder is never muted, hence unmuting should then only be necessary
once after hardware initialization.
I tested this from warm boots and cold boots (with long power down time
to ensure the sram in the chip is emptied), and found that after the
firmware upload the encoder is apparently not muted, making the unmutes
unnecessary.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Jelle Foks <jelle@foks.8m.com>
Remove the unnecessary msleep()'s in cx88-blackbird.c
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Jelle Foks <jelle@foks.8m.com>
This patch should fix the 'muted audio' and 'raspy audio' problem for
mpeg2 streams out of cx88-blackbird devices.
Especially mythtv users would find that the audio would often sound bad
(aliased, or 'raspy'), mainly related to channel changes, many (all?)
other users would find that there was no audio at all in the mpeg data
from the encoder chip, unless the audio was manually unmuted.
The patch includes the following modifications:
Don't actually start the mpeg2 encoder until the device is read from
by the application.
Wait until the audio is stable for at least 400ms before starting the
mpeg encoder.
Mute/Unmute the audio when starting/stopping the mpeg encoder.
Stop the mpeg encoder when changing parameters and when changing tuner
frequency.
Add a variable 'mpeg_active' to struct cx8802_dev to allow tracking of
whether or not the mpeg2 encoder is active.
Load the firmware on cx88-blackbird driver load.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Serge Kolotylo for his help
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Add preliminary support for radio on CX88_BOARD_MSI_TVANYWHERE_MASTER
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the only tuner-specific device that allows special
configurations is tda9887. However, tea5767 also may require some
special configurations (for example, to specify a different Xtal freq).
This patch replaces TDA9887_SET_CONFIG by a more generic internal ioctl
(TUNER_SET_CONFIG). The newer one allows specifying what tuner is
appliable to a configuration set, and allows an arbitrary configuration
struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Original description:
Author: Jaroslav Kysela <perex@perex.cz>
Date: Mon Oct 15 09:50:19 2007 +0200
[ALSA] Changed Jaroslav Kysela's e-mail from perex@suse.cz to perex@perex.cz
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
struct video_device used to define a .hardware field. While
initialized on severl drivers, this field is never used inside V4L.
However, drivers using it need to include the old V4L1 header.
This seems to cause compilation troubles with some random configs.
Better just to remove it from all drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Remove the obsolete VIDIOC_G_MPEGCOMP and VIDIOC_S_MPEGCOMP ioctls from
the V4L2 API as per the removal schedule (October 2007).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
When a cx8802 sub-driver was unregistered, the struct cx8802_driver, which was
kmalloc()ed by cx8802_register_driver(), was deleted from the list of drivers,
but never freed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Less code and more efficient.
Got ride of a variable that counted the number of devices in
cx8802_unregister_driver() but was never used. Looked leftover from a
cut&paste.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
It was a struct cx8802_driver for no apparent reason. Nothing uses a
cx8802_driver in the cx8802_dev struct. The only field that was used was
devlist, a list_head.
The code in cx8802_remove() that removed any loaded sub-drivers was broken.
It would delete the current list entry, but didn't use list_for_each_safe. It
also called list_del() on the list _head_ inside the list_for_each loop? It
would crash if it was run, which I don't think can ever happen.
Since the cx8802 sub-drivers use the cx8802 driver, they have to be unloaded
first. So there isn't any way for a sub-driver to still be loaded when
cx8802_remove() is called... Except maybe with PCI hot-plug, if one removes
the PCI card while the drivers are loaded?
So I left some code in to handle that if it's actually possible. It will
remove the sub-drivers from the device cx8802_remove() was called on, and only
that device. If one has two DVB cards and unplugs one, there is no reason to
unload the DVB drivers for both cards. I have no way to test this, but it
can't be worse than what was there before.
cx8802_get_driver() is passed a cx8802_dev pointer and looks for the requested
driver on that device. It first loops over the cx8802 device list looking for
the device it was passed, which is pointless. It doesn't need to find the
device pointer in the list, as it already has the pointer.
The list_head in the cx8802_driver struct, which joins all the _drivers_
attached to a device, was named devlist. Changed that to drvlist, since the
devlist is used for a list of _devices_ in other cx8802 structs.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
card_priv was only used to store a pointer to the vp3054 state struct.
There's no need to use a void * since it doesn't have multiple types.
Make the field conditional on VP3045 support. It was already conditional on
DVB support, but it's only used if VP3045 support is on, so that makes for a
better option to check.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Add some ifdefs around fields only used for blackbird support, similar to the
way the dvb fields are only included with dvb support.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
CONFIG_VIDEO_BUF_DVB became CONFIG_VIDEOBUF_DVB.
But in these cases, it makes more sense to use CONFIG_VIDEO_SAA7134_DVB
or CONFIG_VIDEO_CX88_DVB_MODULE depending on the driver.
The reference in cx23885.h should just be removed, as the code there needs to
be included if DVB is on or off. I do not think you can even compile the
cx23885 driver without DVB. It's clearly just leftover from when the file was
obvious copied from the cx88 driver (which is not mentioned in the copyright
BTW).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
Thanks to Michael Krufky for pointing this to me.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
PCI-dependent videobuf_foo methods were renamed as videobuf_pci_foo.
Also, videobuf_dmabuf is now part of videobuf-dma-sg private struct.
So, to access it, a subroutine call is needed.
This patch renames all occurences of those function calls to be
consistent with the video-buf split.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
http://thread.gmane.org/gmane.comp.video.video4linux/34978/focus=34981
Reviewed-by: Ricardo Cerqueira <v4l@cerqueira.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
IR workqueue should be disabled during suspend. This avoids some troubles, like
the one reported on bug #8689:
"The Hauppauge HVR 1100 ir-remote control does not work after resume from
suspend to ram or disk."
This patch disables IR before suspending, re-enabling it after resume.
Thanks to Peter Poklop <Peter.Poklop@gmx.at> for reporting it and helping with
the fix.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
A few distro kernels, like Mandriva 2.6.22.9-desktop-1mdv are starting to be
shipped with the newer alsa drivers. This patch changes the compat code for
older kernels in a way that it will be compatible also with those distro
kernels.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
include/sound/tlv.h was first added in 2.6.19
Disable the TLV support for kernels prior to 2.6.19
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Lets mixer apps display a dB range for the volume control.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Not sure why they are there, but they don't do anything now.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Add two mute controls. One mutes everything, the other just mutes the analog
pass-through output.
Rename the existing volume control. The controls are now:
Playback Volume
Playback Switch
Capture Switch
These names might seem odd, but I believe they are more correct. The previous
"Capture Volume" control didn't actually effect the volume of the captured
audio. Instead it controls the volume of the analog pass-thought output. It
appears that pass-through controls like this are usually considered to be in
the playback direction, not capture. For example, "CAPTURE feedback Playback
Volume" is the name used for a control that appears to have the same effect in
the ca0106 driver. We only have one volume control, so we can omit the
"CAPTURE feedback" part.
If someone where to add PCM playback support to the driver, then this would be
the volume control.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Use the balance control to make the mono volume control stereo.
Note that full range isn't supported. The balance control attenuates one
channel by 0 to -63 dB, and the volume control provides additional attenuation
to both channels by another 0 to -63 dB.
So the channel with the most attenuation has a range of 0 to -126 dB, while
the other channel only has a range of 0 to -63 dB. ALSA volume controls don't
appear to support this concept. I just limited the range to 0 to -63 total.
Once you get to -63 dB, you're already at silence, so additional attenuation
is pretty much pointless anyway.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Steven Toth <stoth@hauppauge.com>
Bug: With a hardware encoder board installed as cx88[1] and a
non-encoder boards installed as cx88[0], an OOPS is generated
during cx8802_get_device() called from mpeg_open().
Signed-off-by: Steven Toth <stoth@hauppauge.com>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Michael Krufky <mkrufky@linuxtv.org>
Auto-load ir-kbd-i2c for ir receiver support, and
rtc-isl1208 for rtc support for the FusionHDTV5 RT Gold.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@infradead.org>
Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This
patch removes all occurences of moduleparm.h from drivers/media files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
The revision is part of the pci_dev struct, so there is no need to read it in.
Stop storing the revision and latency in the chip struct, since they're never
used after being printed out when the driver loads.
linux/pci.h wasn't included. It was getting picked up something else,
probably cx88.h, but this file uses struct pci_dev so it should include pci.h.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
channels_min should be 2, not 1. The hardware only supports stereo.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Currently the driver turns on audio interrupts, then sets the audio interrupt
mask to select which interrupts to get. One could received unwanted
interrupts since the mask is set _after_ interrupts have already been turned
on. Change the order of the operations, and clear any audio interrupt status
bits that are already set for good measure.
Before changing the SRAM FIFO parameters, make sure the FIFO isn't being used.
This shouldn't happen with just the ALSA driver, as it should never try to
turn on FIFO/RISC/DMA while they are already on. However, the V4L driver
needs to turn the audio FIFO on for analog audio output to work (undocumented
cx88 bug). The FIFO parameters are in an inconsistent state while they are
updated, and this results in many FIFO sync error IRQs if the FIFO is in use
while it's in this inconsistent state.
Also create and use a bunch of symbolic constants for audio interrupt mask
bits.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
When an irq handled by the cx88 core driver (currently IR and errors) occurs
and the cx88-alsa irq handler is the first called, it will claim to have
handled the irq but it doesn't call cx88_core_irq() to handle it.
The means loading cx88-alsa can disable the IR remote.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Used for the PCI_INTMSK and PCI_INT_STAT registers.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
FM radio transmission use a preemphasis/deemphasis scheme to reduce
high-frequency noise. The cx88 audio decoder is supposedly set to no
deemphasis by the current driver.
However, the "no deemphasis" setting doesn't work. On my chip, cx23883, it
produces the same result as the 75 us time constant. Maybe the default
settings on the cx23881 are for 50 us?
Since the deemphasis time constant varies by country, allow setting it via a
module parameter.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Removed some ALSA compat code from bt87x and put it into compat.h, then use
this code in cx88-alsa and saa7134-alsa to avoid lots and lots of #ifs.
All the kernel version checks in cx88-alsa and saa7134 were off by one too,
which is now fixed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Get rid of the "CORE" prefix from cx88 printks. It was only used a few times,
and it makes it look like they're coming from the kernel core or something.
Fix the message, "TV tuner 60 at 0x1fe, Radio tuner -1 at 0x1fe", by adding a
"cx88[0]" prefix to be consistent, and to keep people who grep their dmesg
output for cx88 from missing it. Get rid of the addresses, which are always
wrong. The addresses are always set to -1, but because it's an unsigned 8-bit
value, the left shift converts it to the nonsense address 0x1fe.
In the cx8802 driver, some cut and pasted code prefixed lines with "CORE
cx88[0]:", which has been changed to "cx88[0]/2:" like the other printks from
the cx8802 driver.
Also fix some ugly printks in the cx8802 driver that used __FUNCTION__ for
KERN_INFO and KERN_ERR messages.
The changed printks in cx88-mpeg.c also needed lots of whitespace and
80-column fixes.
A bunch of misc changes in cx88-dvb.c and cx88-video.c to add message levels
or a consistent "cx88[?]/2" or "cx88[?]/0" prefix.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
A lot of code in cx88-cards.c was only used by cx88-core.c when the core state
is first allocated and initialized. Moving that task to cx88-cards makes the
driver simpler and the files more self contained.
- Module parameters tuner, radio, card, and latency move to cx88-cards.c
- cx88_boards is made static
- cx88_subids is made static and const
- cx88_bcount is eliminated
- cx88_idcount is eliminated
- cx88_card_list() is made static
- cx88_card_setup_pre_i2c() is made static
- cx88_card_setup() is made static
- cx88_pci_quirks() is moved from cx88-core to cx88-cards
The function argument "char *name" is made const too
- get_ressources() is moved from cx88-core to cx88-cards, and renamed to
cx88_get_resources()
- The code to allocate and initialize the core state struct and the chip is
moved out of cx88-core.c:cx88_get_core() and into a new function in
cx88-cards.c, cx88_core_create(). This makes both functions simpler.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
The cx88 driver state stored the ID of the board type in core->board. Every
time the driver need to get some information about the board configuration, it
uses the board number as an index into board configuration array.
This patch changes it so that the board number is in core->boardnr, and
core->board is a copy of the board configuration information. This allows
access to board information without the extra indirection. e.g.
cx88_boards[core->board].mpeg becomes core->board.mpeg.
This has a number of advantages:
- The code is simpler to write.
- It compiles to be smaller and faster, without needing the extra array lookup
to get at the board information.
- The cx88_boards array no longer needs to be exported to all cx88 modules.
- The boards array can be made const
- It should be possible to avoid keeping the (large) cx88_boards array around
after the module is loaded.
- If module parameters or eeprom info override some board configuration
setting, it's not necessary to modify the boards array, which would
affect all boards of the same type.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
An error message for PCI resource allocation failure used the board type
before it was set. Just get rid of the error message, as get_ressources()
[sic] already prints one. Format that error message better, and add the pci
function and subsystem information to better associate the error with what
caused it.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
The vmux setting is only two bits, but was taking up a whole 32 in the input
description struct. By changing it to a two-bit bitfield, it can fit in what
was padding space before and drop the input size by 4 bytes, from 28 to 24.
This drops the board description struct, which has 9 inputs, from 280 to 244
bytes. Total driver size decreases by 2108 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
Add the advanced debug functions to the radio videodev template. One could
already use them from the video and vbi devices.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
After some tedious work with a logic probe and a magnifying glass, I've
determined that GPIO 7 is used to switch between the DTT7612's Sound 4.5 MHz
IF output on pin 12 and the FM 10.7MHz If output on pin 11. GPIO 2 is used to
switch the card's analog sound output from from the analog input connector to
the CX23883's audio DACs.
So, in radio mode GPIO2 = 1 and GPIO7 = 0.
Add some comments about how the HD-3000's GPIOs are connected.
Delete the vmux setting for the radio, as vmux doesn't apply to radio mode.
Also delete the lines setting unused gpio words to zero; it's not necessary as
0 is the default value for uninitialized fields.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Jesper Juhl <jesper.juhl@gmail.com>
This patch cleans up duplicate includes in
drivers/media/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
