| Age | Commit message (Collapse) | Author |
|---|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:
1) It requires that the scancode to be at the range 00-7f;
2) keycodes should be masked on 7 bits in order for it to work;
3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;
4) it is different than what is done with dvb-usb approach;
5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.
This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
u16 scancode;
u32 keycode;
};
This is very close to what dvb does. So, a further integration with DVB
code will be easy.
While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.
The only notable effect is the redution of about 35% of the ir-common
module size:
text data bss dec hex filename
6721 29208 4 35933 8c5d old/ir-common.ko
5756 18040 4 23800 5cf8 new/ir-common.ko
In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.
This patch itself shouldn't be doing any functional changes.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Igor M. Liplianin <liplianin@me.by>
It does matter to set explicitly gpio0 value in
cx88_board structure for TBS 8920 card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
As asked by Jarod Wilson, this patch doesn't work properly. Reverting it.
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jarod Wilson <jarod@redhat.com>
The dvb side of the pcHDTV HD-3000 doesn't work since at least 2.6.29.
The crux of the problem is this: the HD-3000's device ID matches the
modalias for the cx8800 driver, but not the cx8802 driver, which is
required to set up the digital side of the card. You can load up
cx8802 just fine, but cx88-dvb falls on its face, because the call
to cx8802_register_driver() attempts to traverse the cx8802_devlist,
which is completely empty. The list is only populated by the
cx8802_probe() function, which never gets called for the HD-3000, as
its device ID isn't matched by the cx8802 driver, so you wind up
getting an -ENODEV return from cx8802_register_driver() back to
cx88-dvb, and as a result, no digital side of the card for you.
Long story short, by simply adding a vendor/device/subvendor/subdevice
block to cx88-mpeg.c, cx8802_probe() will run, the cx88-2_devlist
will get populated, cx8802_register_driver() won't fail, and cx88-dvb
can actually load up all the way on this card. Channel scanning is
of course currently failing for me still (works fine on several other
cards I have handy), but that's another problem for another day...
There might be a Better Way to do this, and I'm open to suggestions
and willing to try them out, but this Works For Me.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch solves problem of missed keystrokes on some remote controls,
as reported on http://bugzilla.kernel.org/show_bug.cgi?id=9637 .
Changes of version 2:
* Driver no longer builds on kernels < 2.6.22, so add an entry to
v4l/versions.txt
* Add a missing static.
Build-tested on 2.6.22.
Priority: normal
Signed-off-by: Andrzej Hajda <andrzej.hajda@wp.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
[mchehab@redhat.com: this patch will be merged with version 1 for upstream submission]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
It were using 7 spaces instead of tab for indent.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Andrzej Hajda <andrzej.hajda@wp.pl>
Patch solves problem of missed keystrokes on some remote controls,
as reported on http://bugzilla.kernel.org/show_bug.cgi?id=9637 .
Signed-off-by: Andrzej Hajda <andrzej.hajda@wp.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Vlastimil Labsky <vlasta.labsky@gmail.com>
I updated and simplyfied patch from Zbynek Hrabovsky for recent kernel.
It enables autodetection of card, sound in analog TV , sound in FM radio
and switching between antenna and cable RF input. Radio tuner still
doesn't work, I don't even know how it works. Some guys wrote me that FM
radio works with TV tuner used instead of radio part (symlink video0 ->
radio0).
Priority: normal
Signed-off-by: Vlastimil Labsky <vlasta.labsky@gmail.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced. The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured. Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.
Thanks to user "ritec" for reporting the issue and testing the fix.
Priority: high
Cc: rictec <rictec@netcabo.pt>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
The introduction of the zl10353 i2c gate control broke support for the
Geniatech board (which is not behind an i2 gate). Add the needed parameter.
Priority: high
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
|
|
From: Sohail Syyed <linuxtv@hubstar.net>
Current tip is broken and does not switch back to DVB-T correctly
Priority: high
Signed-off-by: Sohail Syyed <linuxtv@hubstar.net>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
|
|
kernel-sync:
Author: Alexey Dobriyan <adobriyan@gmail.com>
Date: Sat Jul 11 22:08:37 2009 +0400
headers: smp_lock.h redux
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.
This simplifies this API substantially.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix Leadtek TV2000 XP Global entries and add missing PCI ID's.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing us for the proper settings.
Priority: normal
CC: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Figo.zhang <figo1802@gmail.com>
bttv-driver.c,cx23885-video.c,cx88-video.c: poll method lose race condition for capture video.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean Delvare <khali@linux-fr.org>
Add missing __devexit_p() to several drivers. Also add a few missing
__init, __devinit and __exit markers. These errors could result in
build failures depending on the kernel configuration.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
By mistake, I've committed a changeset that it is not done yet together
with a fix. Revert the broken part of the old changeset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
The last changeset has an else missing, causing wrong frequencies for
DTV6. Thanks to Terry Wu <terrywu2009@gmail.com> for pointing the issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
The v4l function has a better algorithm for aligning image size.
Priority: normal
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Mostly due to ir-kdb-i2c, but also due to two new drivers, compilation
with kernels older than 2.6.29 were broken.
This quick and dirty changeset, generated semi-automatically, restaures
backport to the subsystem by adding lots of #ifs.
It is possible to write a much more small changeset that would restore
backport without adding so many ifs, but, due to the lack of time, this
will also solve it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Miroslav Sustek <sustmidown@centrum.cz>
Enables analog/digital tv, radio and remote control (gpio).
Signed-off-by: Miroslav Sustek <sustmidown@centrum.cz>
Tested-by: Marcin Wojcikowski <emtees.mts@gmail.com>
Tested-by: Karel Juhanak <karel.juhanak@warnet.cz>
Tested-by: Andrew Goff <goffa72@gmail.com>
Tested-by: Jan Novak <novak-j@seznam.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: figo.zhang <figo.zhang@kolorific.com>
The variable minor have assigned value twice, the first time is in the
initial "video_device" data struct in those drivers, pls see
saa7134-video.c,line 2503.
---
Signed-off-by: Figo.zhang <figo.zhang@kolorific.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Jean Delvare <khali@linux-fr.org>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
According to the engineer at PCTV Systems, the xc5000 reset pin is supposed
to be on GPIO12. However, despite three nights of effort, pulling that GPIO
low didn't reset the xc5000. While pulling MO_SRST_IO low does reset the
xc5000, this also resets in the s5h1409 being reset as well. This causes
tuning to always fail since the internal state of the s5h1409 does not match
the driver's state.
Given that the only two conditions in which the driver performs a reset is
during firmware load and powering down the chip, I am taking out the reset.
We know that the chip is being reset when the cx88 comes online, and not being
able to do power management for this board is better than not having any
tuning at all.
Problem discovered when implementing proper power management for the xc5000,
which results in calls to the reset callback *after* s5h1409 is initialized.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: Chaogui Zhang <czhang1974@gmail.com>
|
|
From: Devin Heitmueller <dheitmueller@kernellabs.com>
A power management fix to properly put the xc5000 into low power mode
revealed a race condition where hald could detect the creation of the device
file and connect to the device while the initial device configuration is
still in progress.
Lock the core structure so that video_release cannot be called and put the
tuner to sleep in the middle of the initial call to cx88_set_tvnorm() in
cx8800_initdev()
Thanks to Michael Krufky for discovering the issue and providing an
environment to test in.
Priority: normal
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Michael Krufky <mkrufky@linuxtv.org>
|
|
From: Pieter Van Schaik <vansterpc@gmail.com>
This patch is for supporting the remote control of the Winfast TV2000
XP Global TV capture card. A case statement was added in order to
initialize the GPIO data structures as well as a case statement for
handling the keys correctly when pressed.
Thanks to Hermann and Mauro for all the help
Signed-off-by: Pieter C van Schaik <vansterpc@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Steven Toth <stoth@linuxtv.org>
cx88: Add support for the Hauppauge IROnly board.
Priority: normal
Signed-off-by: Steven Toth <stoth@linuxtv.org>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
kernel-sync:
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Jan 12 15:17:09 2009 +0100
drivers/media: Convert to snd_card_create()
Convert from snd_card_new() to the new snd_card_create() function.
While here, backport also cx231xx-audio upstream changes for using
snd_card_create().
kernel-sync:
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Author: Yang Hongyang <yanghy@cn.fujitsu.com>
Date: Mon Apr 6 19:01:15 2009 -0700
dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Priority: normal
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Miroslav Sustek <sustmidown@centrum.cz>
Signed-off-by: Miroslav Sustek <sustmidown@centrum.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Miroslav Sustek <sustmidown@centrum.cz>
cx88-dsp: fixing 64bit math on 32bit kernels
Some gcc versions report the missing of __divdi3
Signed-off-by: Miroslav Sustek <sustmidown@centrum.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
This file were supposed to be included on changeset 11394:0eba67ef42ba.
However, it weren't. Sorry for the mess. I'll merge this one with the
original changeset at -git.
This is the original description that also applies to this file:
- cx88: Add support for stereo and sap detection for A2
- From: Marton Balint <cus@fazekas.hu>
The patch implements reliable stereo and sap detection for the A2 sound
standard. This is achieved by processing the samples of the audio RDS fifo of
the cx2388x chip. A2M, EIAJ and BTSC stereo/sap detection is also possible with
this new approach, but it's not implemented yet. Stereo detection when alsa
handles the sound also does not work yet.
Priority: normal
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Marton Balint <cus@fazekas.hu>
This patch changes cx88_set_stereo to avoid resetting all of the audio
registers on stereo/mono change if the audio standard is A2, and set
only the AUD_CTL register. The benefit of this method is that it
eliminates the annoying clicking noise on setting the audio mode to
stereo or mono.
The driver had used the same method 1.5 years ago (and for FM radio it
still does), but a pretty big cleanup commit changed it to the
"complete audio reset" method, although the reason for this move was
not clear. (If somebody knows why it was necessary, please let me
know!)
The original commit: http://linuxtv.org/hg/v4l-dvb/rev/ffe313541d7d
Priority: normal
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Marton Balint <cus@fazekas.hu>
The sole purpose of the audio thread is to detect if stereo transmission is
available, and if it is, then switch to stereo mode (and switch back, if it's
no longer available). This manual autodetection is useful for some audio
standards (e.g. A2) where cx88_get_stereo CAN detect stereo sound, but the
cx2388x chip CANNOT auto-detect stereo sound.
However, for other audio standards, the cx2388x chip CAN auto-detect the stereo
sound, so the manual autodetection in the audio thread is not needed. In fact,
it can cause serious problems because for some of these audio standards,
cx88_get_stereo CANNOT detect the presence of stereo sound. Besides that, if
the hardware automatically detects stereo/mono sound, you cannot set
core->audiomode_current to the real current audio mode on channel change.
With this patch, the manual autodetection is only used if audiomode_current is
known after a channel change (because of the initial mono mode), and
hardware-based stereo autodetecion is not applicable for the current audio
standard.
Priority: normal
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Marton Balint <cus@fazekas.hu>
The patch implements reliable stereo and sap detection for the A2 sound
standard. This is achieved by processing the samples of the audio RDS fifo of
the cx2388x chip. A2M, EIAJ and BTSC stereo/sap detection is also possible with
this new approach, but it's not implemented yet. Stereo detection when alsa
handles the sound also does not work yet.
Priority: normal
Signed-off-by: Marton Balint <cus@fazekas.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
With all the v4l2_subdev changes that were made to these drivers it is a
good idea to increase the version number of each driver.
It's just the patch level that is increased, except for the zoran and saa7146
drivers where the minor number was increased due to the more substantial
changes that were made to those two drivers.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
new_(probed)_subdev
From: Hans Verkuil <hverkuil@xs4all.nl>
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Originally the intention was to switch to the new style i2c API starting with
the introduction of the API in 2.6.22. However, the i2c_new_probed_device()
function has a lethal bug that wasn't fixed until 2.6.25. Or more accurately,
it was only fixed in the stable series of 2.6.25 and 2.6.26.
Given the fact that the new i2c API also changed starting with 2.6.26 (the
addition of i2c_device_id), it is easiest to switch APIs starting with
2.6.26.
This patch updates all the legacy code accordingly.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
s_std didn't belong in the tuner ops. Stricly speaking it should be part of
the video ops, but it is used by audio and tuner devices as well, so it is
more efficient to make it part of the core ops.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
s_standby is only used to put the tuner in powersaving mode, so move it
from core to tuner.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
tuner-core.c contains a hack for cx88 board to prevent probing of certain
addresses:
/* HACK: Ignore 0x6b and 0x6f on cx88 boards.
* FusionHDTV5 RT Gold has an ir receiver at 0x6b
* and an RTC at 0x6f which can get corrupted if probed.
*/
With the new i2c API this hack no longer works. So instead change the
list of tuner probe addresses in the cx88 driver itself, which is much
more clean.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Hans Verkuil <hverkuil@xs4all.nl>
Convert cx88 to use v4l2_subdev since the old i2c autoprobing mechanism
will be removed.
Added code to explicitly load tvaudio where needed. Also fix the rtc-isl1208
support: since that driver no longer supports autoprobing it has to be
loaded using the new i2c API.
Priority: normal
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
From: Trent Piepho <xyzzy@speakeasy.org>
The ->vidioc_(s|g|try|enum)_fmt_vid_cap() methods are only called on
VIDEO_CAPTURE buffers. Thus, there is no need to check or set the 'type'
field since it must already be set to VIDEO_CAPTURE.
Priority: normal
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
|
|
From: Alan Cox <alan@lxorguk.ukuu.org.uk>
The ioremap one was reported in October 2007 (Bug 9146), the kmalloc one
was blindingly obvious while looking at the ioremap one
The bug suggests some other configuration for lots of I/O memory (32MB per
device is ioremapped) but I'll leave that to the real maintainers
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
