path: root/doc/faq/faq.sgml

<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook V4.1//EN" [
<!ENTITY intro SYSTEM "intro.sgml">
]>

<book>

<bookinfo>
  <title>The xine engine FAQ</title>
  <titleabbrev>xine FAQ</titleabbrev>
  <copyright>
    <year>2001-2003</year>
    <holder>the xine project team</holder>
  </copyright>
</bookinfo>

<chapter id="general">

  <title>General questions about xine and this document</title>

  <sect1 id="about">

    <title>What is the xine engine?</title>

    <para> 
      The xine engine is a free media player engine. It comes in the form of
      a shared libarary and is typically used by media player frontends
      and other multimedia applications for playback of multimedia streams
      such as movies, radio/tv network streams, DVDs, VCDs.
    </para>

  </sect1>

  <sect1 id="scope">
    
    <title> What's the aim and scope of this text? </title>

    <para>
      The primary goal of this FAQ is to cover all recurring questions related
      to the xine engine. Frontend specific questions are not covered here.
    </para>

  </sect1>

  <sect1 id="wheretogethelp">

    <title> My question is not yet covered here - where can I ask for help? </title>

    <para>
      First of all be sure that your question is really not covered here and
      that you haven't just been a bit too lazy to read through all of this
      text. ;-). Also check out the xine HOWTO and documentation specific to
      the frontend (e.g. <command> xine-ui </command> or <command> gxine </command> or 
      <command> totem </command>).
    </para>
    
    <para>
      That said - you are welcome to mail to our user mailing list:
    
      <email>xine-user@lists.sourceforge.net</email>

      Please provide some info about your setup so people have a chance to
      help you, e.g. include information about your audio/video hardware
      and drivers you use, operating system, cpu type and some console
      output/any error messages. Also include command line parameters you
      have specified and information about the type of stream you're
      trying to play back. Also very important is the version of xine
      you're using and information about any additional plugins you
      may have installed on your system.
    </para>

  </sect1>

  <sect1 id="modules">

    <title> What are those xine-lib, xine-ui, gxine, ... modules in cvs for? </title>

    <para>
      Some time ago xine just became too complex to be just one big program.
      Therefore it was split into two major parts.
    </para>
    
    <para>
      xine-lib is simply speaking the engine of xine. It contains all plugins
      and is necessary to run anything that relies on xine (this is the part that
      is covered in this FAQ).
    </para>

    <para>
      Then there are frontends - applications that use xine. The most
      common frontend is that of a media player. There are currently
      two frontends being developed in the xine project, xine-ui (skinned
      dvd-player style frontend directly based on xlib) and gxine,
      a desktop media-player style frontend using the standard gtk widget set
      and comes with a mozilla browser plugin.
      External projects like sinek and totem develop additional frontends.
      In the future you will likely see more and different types of apllications
      being developed which will use the xine engine for video processing
      and other multimedia purposes.
    </para>

    <para>
      If you simply want a media/dvd player, you'll need to install xine-lib
      first and then choose and install a player frontend like xine-ui or gxine.
    </para>

    <para>
      Other modules in CVS: <filename>xine-plugin</filename> a mozilla browser plugin
      for streaming media playback using xine (at the time of this writing 
      unmaintained and somewhat obsoleted by gxine's browser plugin), 
      <filename>xine-www</filename> the
      xine project website sources.
    </para>

  </sect1>

  <sect1 id="cvs">

    <title> Where and how do I get the latest development version? </title>

    <para>
      Be advised that end-users should stick to the official xine releases.
      CVS is only intended for developers.
    </para>
    
    <para>
      To check out xine-modules from CVS, first do this:
    </para>
    <para>
     <command> cvs -d :pserver:anonymous@cvs.xine.sourceforge.net:/cvsroot/xine login </command>
     [empty password]
    </para>
    <para>
      then, to check out individual modules (e.g. <filename>xine-lib</filename>, 
      <filename>gxine</filename>, <filename>xine-ui</filename>):
    </para>
    <para>
    <command>cvs -d :pserver:anonymous@cvs.xine.sourceforge.net:/cvsroot/xine co modulename</command>
    </para>

  </sect1>

  <sect1 id="binaries">

    <title> Where can I find pre-compiled binaries, e.g. RPMs? </title>

    <para>
      The xine project does not provide pre-compiled binaries for legal
      reasons (some parts of xine may be covered by patents in some countries).
      Some OS projects/vendors (e.g. debian, freebsd, ...) offer binaries
      for their distributions - please contact them for further info.
      You can also find links to third parties providing xine RPMs on
      the xine homepage :
      <ulink url="http://xine.sf.net/index.php/about">http://xine.sf.net/index.php/about</ulink>
    </para>
    
    <para>
      See the next chapter of this FAQ for instructions on how to build xine
      from source.
    </para>

  </sect1>

</chapter>

<chapter id="building">

  <title> Building and installing xine from source </title>

  <sect1 id="buildrequirements">

    <title> What do I need to compile everything properly? </title>

    <para>
      First of all an official and stable release of gcc. Also be aware 
      that patched gcc versions may break parts of xine and are therefore 
      not supported by the xine project.
    </para>
    
    <para>
      Furthermore you'll have to use GNU make to compile xine. On most GNU/Linux
      systems "make" is GNU make - on other platforms use "gmake" instead.
      Also, zlib iss required (including the appropriate header files, which are
      often found in a package called zlib-devel or similar.)
    </para>

    <para>
      If you want to compile xine from CVS, you'll need to have the autobuild tools
      installed (automake, autoconf and libtool - in recent versions).
    </para>

    <para>
      Frontends might need additional libraries, e.g. for gxine you'll need to have
      GTK installed. Make sure you have not only the shared libraries themselves
      but also the header files (often packaged seperately as so-called -dev packages)
      on your system.
    </para>

    <para>
      Some plugins that come with the xine engine need additional libraries (otherwise
      they will not be built). For example, libogg and libvorbis (plus their include files)
      are needed for ogg/vorbis support. 
    </para>

    <para>
      Don't worry about this too much right now, xine's <command>configure</command>
      (see below) will check for all the stuff needed and will tell you what's missing
      (which means that you should check the output it produces carefully ;) )
    </para>
  </sect1>

  <sect1>

    <title> How do I compile xine? </title>

    <sect2 id="simplebuildinstr">
    
      <title> Simple build instructions for beginners </title>

      <para>
        Download the latest xine-lib and gxine/xine-ui tarballs, then follow
        these instruction. To unpack a tarball, use:
      </para>
      <programlisting>
        tar xfvz tarballname.tar.gz
      </programlisting>
      <para>
        The following instructions will install xine in <filename>/usr/local</filename> for all
        users. You need root privileges to do this on most systems.
      </para>
      <para>
        First unpack xine-lib, then:
      </para>
      <programlisting>
        ./configure
	make install
      </programlisting>
      <para>
        Make sure your <filename>/etc/ld.so.conf</filename> contains 
	<filename>/usr/local/lib</filename>, then:
      </para>
      <programlisting>
        ldconfig
      </programlisting>
      <para>
        Now unpack your frontend (gxine or xine-ui or ...), then:
      </para>
      <programlisting>
        ./configure
	make install
      </programlisting>

    </sect2>    

    <sect2 id="completebuildinstr">
    
      <title> Complete build instructions </title>

      <para>
        The build process is the same for all of the xine modules.
      </para>
      <para>
        You have to start with xine-lib. If built and installed successfully, you
        can continue with the frontend(s).
      </para>
      <para>
        If you have installed xine-lib to a non-standard prefix, make sure you
        that you have <filename>$prefix/bin</filename> in your PATH and that your linker finds
        libs in <filename> $prefix/lib </filename> - otherwise trying to build modules that
        rely on xine-lib will fail with configure complaining about not
        finding certain parts of libxine. Using bash you can do something like:
      </para>
      <programlisting>
      export PATH="$prefix/bin:$PATH"
      export LD_LIBRARY_PATH="$prefix/lib:$LD_LIBRARY_PATH"
      </programlisting>
      <para>
        to make sure libxine can be found by the frontend(s).
      </para>
      <para>
        Last but not least. Here the build instructions. As stated earlier,
        those are the same for every xine module.
      </para>
      <programlisting>
      ./autogen.sh [-> *only* if you checked your sources out of CVS]
      ./configure
      make
      make install
      </programlisting>

    </sect2>    

  </sect1>

  <sect1 id="rpmbuild">

    <title> Making your own RPM packages (xine-lib, xine-ui) </title>

    <para>
      Basically you will only have to issue one command, if you have just
      downloaded a source tarball from our web site:
    </para>
    
    <para>
      <command> rpm -ta THE_NAME_OF_YOUR_SOURCE_TAR_BALL </command>
    </para>
    
    <para>
      This will start the binary and source RPM building. After compiling is
      finished, a binary rpm is placed in your rpm binary directory which is
      usally <filename>/usr/src/RPM/RPMS/[YOUR_ARCHITECTURE]</filename> and a source RPM is written
      to your rpm source dir (e.g. <filename>/usr/src/RPM/SRPMS</filename>).
    </para>
    
    <para>
      In case that you have a fresh CVS checkout, you will need to do the
      following first in order to get a tarball release out of it which you
      can later use with the <command> rpm -ta </command> command above:
    </para>
    
    <para>
      <command> ./autogen.sh && make clean && make dist </command>
    </para>
    
    <para>
      In any case, please keep in mind that you have to build and install
      xine-lib first before you can proceed with xine-ui.
    </para>
    
  </sect1>

  <sect1 id="cflags">

    <title> Can I provide additional CFLAGS for compilation? </title>

    <para>
      Yes, you can do so by setting the CFLAGS variable and then run
      configure again.
    </para>
    
    <para>
      This can be useful to specify additional include paths or library paths
      to the compiler.
    </para>

    <para>
      Example: <command> export CFLAGS="-I/usr/include -L/home/guenter/xine_libs" </command>
    </para>

  </sect1>

  <sect1 id="athlonflags">

    <title> Are there binaries for my AMD K7 (Athlon (TM) ) available? Can I build them? </title>

    <para>
      If you have a recent gcc you can try to compile "more" k7 support in (esp.
      better instruction scheduling). If the configure script should fail to
      detect your processor/gcc correctly, try setting the xine_BUILD envvar
      explicitly to a valid description string for your configuration, e.g.
    </para>
    
    <programlisting>
    export xine_BUILD=k7-pc-linux-gnu
    rm -f config.cache
    ./autogen.sh
    make
    make install
    </programlisting>

  </sect1>

  <sect1>

    <title> Build problems: xine engine (xine-lib) </title>

    <sect2 id="doesntcompile">

      <title> The package doesn't compile at all! </title>

      <para>
        In order to be able to compile xine-lib, you need (amongst other things)
        the zlib compression library plus the appropriate headers, which are
        often found in a package called zlib-devel or similar.
      </para>
    
      <para>
        Read again carefully the output <command>./configure</command>
	produced and/or compiler warnings and error reports, they often contain
	helpfull information to find out what's going on. If you're stuck here
	and decide to post your problem on the xine-user mailing list,
	make sure you include these outputs.
      </para>

    </sect2>
    <sect2 id="xvpluginfailstobuild">

      <title> The Xv video-out plugin fails to compile! </title>

      <para>
        If you want to have Xv support compiled in, make sure you either have
        a shared Xv library on your system, e.g. 
	<command> ls /usr/X11R6/lib/libXv* </command>
        should give you some .so libs, like this:
        <programlisting>
          /usr/X11R6/lib/libXv.a
          /usr/X11R6/lib/libXv.so
          /usr/X11R6/lib/libXv.so.1
        </programlisting>
      </para>
    
      <para>
        Alternatively you need to have libtool 1.4 or newer installed, then 
	libXv.a is sufficient. Otherwise you can create the shared versions yourself:
        <programlisting>
          ld --whole-archive -shared -o libXv.so.1 libXv.a
          ln -s libXv.so.1 libXv.so
          ldconfig
        </programlisting>
      </para>

      <para>
        Now you should be ready to build the Xv video-out plugin on your system.
      </para>

    </sect2>

  </sect1>

  <sect1>

    <title> Build problems: frontend (gxine/xine-ui/...) </title>

    <sect2 id="xinelibnotfound">

      <title> I have installed xine-lib but the frontend complains about not finding it!</title>

      <para>
        First of all take a closer look at the compilation instructions above again. 
	You will probably find your answer there right away.
      </para>
    
      <para>
        As stated there (there again that hint *grin*), make sure that you
        have <filename> $prefix/bin </filename> in your path and that your 
	linker is able to find
        libraries installed in <filename>$prefix/lib</filename> (by the way, $prefix is where you
        installed your xine-lib to earlier (yes, installing xine-lib with
        <command> make install </command> would be a good idea before trying to compile 
	the frontend ;)).
      </para>

    </sect2>
  </sect1>

  <sect1 id="nonrootbuild">

    <title> Can I install xine in my home directory (without being root) ? </title>

    <para>
      yes. first set up a subdir where you install your private software, eg
    </para>
    <programlisting>
      $ mkdir ~/usr
    </programlisting>
    <para>
      then you have to set a few environment variables - it's probably a good
      idea to add this to your <filename> ~/.bashrc </filename> (or somewhere similar):
    </para>
    <programlisting>
      export PATH="$HOME/usr/bin:$PATH"
      export LD_LIBRARY_PATH="$HOME/usr/lib:$LD_LIBRARY_PATH"
      export CFLAGS="-I$HOME/usr/include -L$HOME/usr/lib -O3"
      export ACLOCAL_FLAGS="-I $HOME/usr/share/aclocal"
    </programlisting>
    <para>
      now you can unpack tarballs e.g. in <filename>~/usr/src</filename> 
      (<command>mkdir  ~/usr/src</command> if necessary) and do a
    </para>
    <programlisting>
      $ ./configure --prefix=$HOME/usr
      $ make install
    </programlisting>
  </sect1>

</chapter>

<chapter id="playback">

  <title>Playback of various stream types</title>
  
  <sect1>

    <title>DVD Playback with xine</title>

    <sect2 id="dvdplayback">

      <title>How do I play back DVDs with xine?</title>
  
      <para>
        Newer xine (1.0.x) releases come with a full-featured
        DVD plugin that should be able to handle any unencrypted,
        non-locked DVD with full menu navigation support. No external
        plugins are required anymore here.
      </para>

      <para>
        To get DVD playback working, first make sure you have
        a symlink <filename>/dev/dvd</filename> pointing to your
        DVD device on your system. For example, if your DVD drive
        is the master ide drive on the second IDE channel,
        <filename>/dev/dvd</filename> should point to
        <filename>/dev/hdc</filename>. Please note that if you
        are using the ide-scsi emulation on your system, it is
        likely that you dvd drive got mapped to a scsi device
        node even though it is an ide drive. In that case first
        check out you boot/kernel logs (or run <command> cdrecord -scanbus </command>)
        to find out which device it got mapped to and set the
        symlink accordingly (should be something like <filename>/dev/scd0</filename>,
        <filename>/dev/scd1</filename>, ... in that case).
        Also make sure you (as a user) have sufficient (read) permissions
        on your dvd drive (this could mean you either have to change the device
        permissions or add your user to a special group 
	(e.g. <command>addgroup cdrom username</command>),
        depending on your setup and/or distribution.
      </para>

      <para>
        It is highly recommended to switch DMA mode on for your DVD drive
        (without it even very recent machines will have trouble producing
        smooth video output). Use a command like
        <command>hdparm -d 1 device</command>
        on your dvd device. Please note that even if you're using ide-scsi
        you will have to set the dma flag on the ide device node (e.g. 
        <filename>/dev/hdc</filename>), not the mapped <filename>/dev/scd</filename>
        scsi device.
      </para>

      <para>
        To be able to play back encrypted dvds you need to have
        libdvdcss installed on your system (please check if this is legal where
        you live).
      </para>

      <para> 
        Newer (post-2000) dvd drives (so-called RPC-2 drives) check the dvd
        region, which means they'll prevent you from playing back dvds that have
        a different region code from what the drive is set up for (most drives
        come with a factory setting of region 0 so they can only play back
        region 0 dvds and there are not many of those available). The easiest
        way to handle this is to use the regionset utility from
        <ulink url="http://www.linuxtv.org/download/dvd/dvd_disc_20000215.tar.gz">
        http://www.linuxtv.org/download/dvd/dvd_disc_20000215.tar.gz</ulink>.
      </para>

      <para>
        Once you have everything set up, try something like
	<command> gxine dvd:// </command> or <command> xine -p dvd:// </command>
	to start dvd playback. Some frontend also offer so-called autoplay
	buttons or menu entries that start dvd playback immediately. 
      </para>

      <para>
        Important: do not try to mount the DVD. Just insert it and hit the DVD autoplay
	button or start xine from the command line.
      </para>

      <para>
        If things do not work as expected, try running the <command> xine-check </command>
	shellscript that comes with libxine to see if this gives you further hints on
	what could be wrong.
      </para>

    </sect2>

    <sect2 id="dvdlongwait">
       <title> DVD playback works, but it takes a long time until playback starts </title>
       <para>
         This points to a region code problem. Some versions of libdvdcss can play
	 back DVDs from other regions than the RPC-2 DVD drive is set up for,
	 but this usually means a cryptographic attack (which takes time) has
	 to be used to access the DVD.
       </para>

       <para>
         You can download a tool to set the region code of RPC-Drives here:
	 <ulink url="http://linuxtv.org/download/dvd/dvd_disc_20000215_css.tar.gz">
	 http://linuxtv.org/download/dvd/dvd_disc_20000215_css.tar.gz
	 </ulink>
       </para>

       <para>
         Warning: Please be aware that the number of region code changes in RPC-2
         drives is limited (usually about 5 times), after that your drive will
         stay locked to the region you last set it up for.
       </para>
    </sect2>    

    <sect2 id="regionset">
       <title>  I have problems setting up my RPC-2 drive for the right region! </title>
       <para>
         You can download a tool to set the region code of RPC-Drives here:
	 <ulink url="http://linuxtv.org/download/dvd/dvd_disc_20000215_css.tar.gz">
	 http://linuxtv.org/download/dvd/dvd_disc_20000215_css.tar.gz
	 </ulink>
       </para>

       <para>
         Warning: Please be aware that the number of region code changes in RPC-2
         drives is limited (usually about 5 times), after that your drive will
         stay locked to the region you last set it up for.
       </para>
    </sect2>    
  </sect1>

  <sect1 id="vcdsupport">

    <title> Can I watch Video CDs (VCDs)? SVCDS ? CD-i?</title>

    <para>
      xine supports VCD and SVCD playback out-of-the box. Similar to DVDs,
      make sure you have a <filename>/dev/cdrom</filename> alias pointing
      to your CDROM drive which you will use to play back the (S)VCD.
    </para>

    <para>
      At the moment, CD-i formats are not supported by xine.
    </para>

    <para>
      Do not try to mount the (S)VCD. Simply insert it into your CDROM drive
      and hit the VCD autoplay button or start something like
      <programlisting>
      gxine VCD://
      </programlisting>
      from the command line.
    </para>

  </sect1>

  <sect1 id="quicktime">

    <title> Can I watch Quicktime (.mov, .mp4) files using xine? </title>

    <para>
       Quicktime is just a system layer (container format) which can contain various 
       different audio and video formats. The system layer itself is fully supported
       in xine. However, only very few typically used quicktime audio/video codecs
       are natively supported yet. Luckily, if you are using a x86 compatible machine
       (any recent PC hardware should do) you can install and use the original
       Quicktime DLLs and watch most streams (trailers) that can be downloaded from the net.
    </para>

    <para>
       Possibly the most convenient way to get the Quicktime DLLs is to download
       them from the mplayer website 
       <ulink url="http://www1.mplayerhq.hu/MPlayer/releases/codecs/">
       http://www1.mplayerhq.hu/MPlayer/releases/codecs/</ulink>.
       The package is called "QuickTime5 DLLs". Unpack it and move everything you find
       inside to <filename>/usr/lib/win32</filename> (actually you can place them
       anywhere you want, e.g. someplace in your homedirectory, but then you'll
       have to set <parameter>codec.win32_path</parameter> in your
       xine config file accordingly). Restart xine then and you should be
       able to watch Quicktime trailers.
    </para>       

  </sect1>

  <sect1>

    <title> Real Network files/streams </title>
    
    <sect2 id="realfileplayback">
      <title> Can I watch Real (.rm, .ram) files using xine ? </title>

      <para>
        The situation with real files and streams is pretty similar to the situation
	with Quicktime Streams (see above). Most newer real audio and video formats
	are only supported by using binary-only codecs which are available from
	real networks but are not included in xine.
      </para>

      <para>
        One way to get these codecs is to download and install RealPlayer from
	RealNetworks, for example in <filename>/usr/local/RealPlayer8</filename> or
	<filename>/opt/RealPlayer8</filename>. If you installed it in one of these
	places, xine should automatically find and use the real binary codecs.
	If it doesn't work, try to find out the exact path to where the real codecs
	are installed on your system (look for a file named <filename>rv30.so.6.0</filename>
	which should reside in a directory called <filename>Codecs</filename> in the
	directory where you have installed RealPlayer in) and set
	<parameter>codec.real_codecs_path</parameter> in your xine config file
	accordingly.
      </para>

    </sect2>

    <sect2 id="realnetworkstreams">
      <title> What about (live) network streams (pnm://, rtsp:// style urls) ? </title>

      <para>
        xine supports both pnm and rtsp streaming. However, digging out the actual
	pnm/rtsp url can be tricky as they're often packed into heavy JavaScript and
	HTML code on most websites. You can either use a combination of your
	browser's "save source" function and wget or use a xine browser plugin
	(currently the gxine frontend comes with a simple mozilla plugin,
	for example). When you decided to dig out the url by hand don't get fooled
	by the many redirectors that are often placed around the actual url.
	Use wget to download any http://-style urls and use less to look inside
	the downloaded .ra/.ram files where you will find the actual pnm/rtsp
	url which can be opened using xine.
      </para>

    </sect2>
  
  </sect1>

  <sect1 id="wmv">

    <title> Can I watch Windows Media (.asf/.wmv) files using xine? </title>

    <para>
      While the container format (system layer) ASF (wmv is just an alias)
      is fully supported in xine, for newer windows media 8 and 9 based streams
      you'll need to install windows binary codecs (.DLLs).
    </para>

    <para>
       Possibly the most convenient way to get the windows DLLs is to download
       them from the mplayer website 
       <ulink url="http://www1.mplayerhq.hu/MPlayer/releases/codecs/">
       http://www1.mplayerhq.hu/MPlayer/releases/codecs/</ulink>.
       The package is called "Win32 Codecpack". Unpack it and move everything you find
       inside to <filename>/usr/lib/win32</filename> (actually you can place them
       anywhere you want, e.g. someplace in your homedirectory, but then you'll
       have to set <parameter>codec.win32_path</parameter> in your
       xine config file accordingly). Restart xine then and you should be
       able to watch windows media streams.
    </para>       

  </sect1>

  <sect1 id="dvb">

    <title> Can I watch Digital TV (Digital Video Broadcast) using xine ? </title>

    <para>
      At the time of this writing DVB support is a very new and experimental
      feature in xine. The number of supported cards is pretty limited at the moment.
      See <filename>doc/README.dvb</filename> (in the xine-lib tarball) for details.
    </para>

  </sect1>

  <sect1 id="stdin">

    <title>How do I play streams from STDIN?</title>
    
    <para>
      Use something like:
      <programlisting>
        cat stream.mpg | gxine stdin://
      </programlisting>    
    </para>
  </sect1>

  <sect1 id="avisubtitles">

    <title> How can I watch files with external AVI subtitles?</title>
    
    <para>
      This is not supported in current xine 1.0.x releases (but it is being
      actively worked on, so please be patient :) ). In xine 0.9.13
      this used to be:
      <programlisting>
        xine foo.avi%bar.sub
      </programlisting>    
    </para>
  </sect1>

</chapter>

<chapter id="running">

  <title> Running xine </title>
  
  <sect1 id="speedup">

    <title>I have a lot of dropped frames - what can I do?</title>
    
    <para>
      Your hardware might be too slow for xine. Make sure you turn on all
      speed optimizing options. A few things you should check (in order of
      importance):

      <itemizedlist>
        <listitem>
	  <para>
            First of all, run the <command>xine-check</command> script included in xine-lib
            package (probably already installed in your system).
	    <command>xine-check</command> will report several of the most common problems
            listed here. Sample output from xine-check:
            <programlisting>
              $ xine-check
              Please be patient, this script may take a while to run...
              [ good ] you're using Linux, doing specific tests
              [ good ] looks like you have a /proc filesystem mounted.
              [ good ] You seem to have a reasonable kernel version (2.4.18)
              [ good ] intel compatible processor, checking MTRR support
              [ good ] you have MTRR support and there are some ranges set.
              [ good ] found the player at /usr/local/bin/xine
              [ good ] /usr/local/bin/xine is in your PATH
              [ good ] found /usr/local/bin/xine-config in your PATH
              [ good ] plugin directory /usr/local/lib/xine/plugins exists.
              [ good ] found input plugins
              [ good ] found demux plugins
              [ good ] found decoder plugins
              [ good ] found video_out plugins
              [ good ] found audio_out plugins
              [ good ] skin directory /usr/local/share/xine/skins exists.
              [ good ] found logo in /usr/local/share/xine/skins
              [ good ] I even found some skins.
              [ good ] /dev/cdrom points to /dev/hdc
              [ good ] /dev/dvd points to /dev/hdc
              [ good ] DMA is enabled for your DVD drive
              [ good ] found xvinfo: X-Video Extension version 2.2
              [ good ] your Xv extension supports YUV overlays (improves MPEG performance)
              [ good ] your Xv extension supports packed YUV overlays
              [ good ] Xv ports:  YUY2 YV12 I420 UYVY      
            </programlisting>
	  </para>
  	</listitem>
	<listitem>
	  <para>
            Try to use the Xv driver, it greatly improves performance and quality
            because hardware does image scaling and color conversion. The 
            <link linkend="video">video section</link> contains important information
            about several Xv drivers. 
	  </para>
	  <para>
	    If Xv cannot be used for some reason, make sure your display is set up
            to 16bpp, not 24 or higher (reduces memory bandwith). Some Xv drivers
            may also have better performance with 16bpp.
	  </para>
	</listitem>
	<listitem>
	  <para>
	    Make sure the hard drive (or cdrom/dvd drive) which supplies the
            video data is in DMA mode (if supported) 
	  </para>
	  <para>
	    On most linux-based systems, you can use hdparm to check this. 
            Example:
	    <programlisting>
              hdparm /dev/hda

              ...
              using_dma    =  1 (on)
              ...
	    </programlisting>
	  </para>
	  <para>
  	    You can enable DMA mode with the following command:
	    <programlisting>
              hdparm -d1 device_of_your_drive_that_supplies_video_data
	    </programlisting>
	    In some cases where this fails it helps to specify the dma mode
	    to use, for example:
	    <programlisting>
              hdparm -d1 -X 66 device_of_your_drive_that_supplies_video_data
	    </programlisting>
	    In RedHat 8.0 an additional entry in /etc/modules.conf
	    <programlisting>
	      options ide-cd dma=1
	    </programlisting> 
	    should help (reboot for this change to take effect).
	  </para>
	  <para>
            More information about this may be found here:
            <ulink url="http://oreilly.linux.com/pub/a/linux/2000/06/29/hdparm.html">
	    http://oreilly.linux.com/pub/a/linux/2000/06/29/hdparm.html
	    </ulink>
	  </para>
	</listitem>
	<listitem>
	  <para>
            Use a recent kernel which is optimized for your hardware. Old kernels
            may lack support for accelerated instructions like SSE, for example.
	  </para>
  	</listitem>
	<listitem>
	  <para>
	    Close other applications (use a tool like "top" to find out
            what applications are using up CPU power). Programs that update the
            system clock like ntp should also be disabled.
	  </para>
	</listitem>
	<listitem>
	  <para>
	    Enable MTRR support in your kernel. If you are still using XFree 3.x,
            you'll have to tell the kernel yourself where the graphics memory is.
            You'll find details about that in the linux dvd howto.
	  </para>
	  <para>
            If you're using XFree 4.x, enabling MTRR support in your kernel should
            be enough (use a recent kernel!).
	  </para>
	  <para>
	    Try a <command> cat /proc/mtrr </command> - if the file exists and you find an entry
            corresponding to the amount of graphics memory you have, everything
            should be fine.
	  </para>
	</listitem>
	<listitem>
	  <para>
            Have your X-server (usually XFree86) running with higher priority.
            Most recent linux distributions (like RedHat 8.0 or Mandrake 9.0) should
            do that for you, improving not only xine but desktop responsiveness
            in general. 
	  </para>
	  <para>
            Use the "top" utility and verify under the "NI" column if
            the X process has a negative value, this indicates a higher priority.
            See "The X Window User HOWTO - Performance considerations" for 
            further instructions 
            <ulink url="http://www.tldp.org/HOWTO/XWindow-User-HOWTO/performance.html">
            http://www.tldp.org/HOWTO/XWindow-User-HOWTO/performance.html</ulink>
	  </para>
	</listitem>
	<listitem>
	  <para>
            Use the latest or a known-good gcc version.
	  </para>
	</listitem>
	<listitem>
	  <para>
            Besides boosting X-server priority, sometimes it's possible to avoid
            discarding frames by making xine itself higher priority. This is not
            a recommended  pratice since it will require to run xine as root,
            but you may give it a try if you want:
              <programlisting>
                nice --5 xine
              </programlisting>    
	  </para>
	</listitem>
	<listitem>
  	  <para>
            xine needs high speed memory access which depends on your chip set.
            Make sure you enable all speed-improving options. 
	  </para>
	  <para>
	    Especially the via apollo pro chipset is known to be quite weird,
            (most of all on my gigabyte board). If you can't configure the ram
            access thoroughly using the bios you might want to try some really
            nasty tricks, as explained on (for example):
	  </para>
	  <para>
	  <ulink url="http://www.overclockers.com/tips105/index03.asp">http://www.overclockers.com/tips105/index03.asp</ulink>
	  </para>
	  <para>
	    This website centers around a windows-tool to tweak the chipset, you
            can do the same on FreeBSD with <command>pciconf</command>. 
	    On some linux distributions there are similar tools.
	  </para>
	</listitem>
	<listitem>
	  <para>
	     a nice performance tuning tool can be found here:
	     <ulink url="http://powertweak.sourceforge.net">http://powertweak.sourceforge.net</ulink>
	  </para>
	</listitem>
	<listitem>
	  <para>
	    Set up and use raw devices for dvd access. Please note that
	    this is usually not worth the effort as the performance gain
	    from it is very small if any.
	  </para>
	  <para>
            Raw devices should be available in linux kernel 2.4.x and there are
            patches for older kernels available from:
	    <ulink url="ftp://ftp.kernel.org/pub/linux/kernel/people/sct/raw-io/">
	    ftp://ftp.kernel.org/pub/linux/kernel/people/sct/raw-io/
	    </ulink>
	  </para>
	  <para>
	    To use raw devices, first connect a free raw device to your dvd
            device, use something like:
	    <programlisting>
  	      raw /dev/raw1 /dev/hdc
	    </programlisting>
	  </para>
	  <para>
	    then create a link named "rdvd" pointing to that raw device:
	    <programlisting>
  	      raw /dev/raw1 /dev/hdc
	    </programlisting>
	  </para>
	</listitem>
      </itemizedlist>
    </para>

  </sect1>

  <sect1 id="ports">

    <title>I have problems when using xine on FreeBSD, Solaris, ... !</title>
    
    <para>
      Check out the the corresponding README files in the directory <filename>xine-lib/doc</filename>
    </para>
  </sect1>


  <sect1 id="aaxine">

    <title> What is aalib? How do I use it in xine? </title>
    
    <para>
      aalib is an ascii art library. xine comes with an aalib video output
      plugin so you can watch movies in your xterm, on the console or on your
      old vt100 - very cool ;> ... another nice option is to preview movies
      on a remote server in your shell over ssh.
    </para>
    <para>
      To use it make sure you have aalib installed correctly before you
      configure/build xine-lib and xine-ui. In addition to the <command>xine</command> binary a
      binary named <command>aaxine</command> should get built and installed. You can then use
      something like:      
      <programlisting>
        aaxine foo.mpg
      </programlisting>
      to use aalib video output.
    </para>
  </sect1>

  <sect1 id="configoptions">

    <title>What do all these <filename>~/.xine/config</filename> (<filename>~/.gxine/config</filename>) entries mean?</title>
    
    <para>
      You can find information about them in 
      <filename>xine-lib/doc/README.config_en</filename>. 
      Frontends may register additional config entries, you may find out more about
      them in their documentation. Also the comments in the config file might
      help.
    </para>
  </sect1>
</chapter>

<chapter id="audio">

  <title> Audio related questions </title>
  
  <sect1 id="audiodrivers">

    <title>What audio drivers does xine support? OSS? Alsa? Arts? Esd?</title>
    
    <para>
      Currently xine support audio output via OSS (kernel audio drivers),
      ALSA 0.9.x (ALSA 0.5.x is no longer supported), arts (KDE's sound daemon)
      and esound (esd, gnome's sound daemon - not recommended because it has
      serious issues with a/v sync).
    </para>
  </sect1>

  <sect1 id="compressor">

    <title> When I'm watching a movie, the sound effects are much higher volume than the voices</title>
    
    <para>
      Congratulations, you seem to have an original movie audio track there.
    </para>
    <para>
      Uhm. So you don't like it. Well, there are two things you can do:

      <itemizedlist>
        <listitem>
	  <para>
	    You can enable xine's audio compressor. Most frontends have
	    a settings window and in that you'll find a slider for the
	    compressor setting. The values are percent values, so a 
	    slider setting of 200 means that xine will double the volume
	    of silent parts of the movie (loud parts stay the same).
	  </para>
	</listitem>
        <listitem>
	  <para>
	    If you have a dolby digital (AC3) soundtrack, you can try
	    to enable liba52's dynamic range compression setting
	    <programlisting>
	      codec.a52_dynrng:1
	    </programlisting>
	    in your xine config file (or use some gui config dialog).
	  </para>
	</listitem>
      </itemizedlist>

    </para>
  </sect1>
  <sect1 id="noaudio">

    <title> When I play this stream, xine shows video but there's no audio!</title>
    
    <para>
      Well, first try a different audio driver (<command> gxine -A oss </command>,
      <command> gxine -A arts </command>, <command> xine -A alsa </command> ...). 
    </para>
    <para>
      If this problem only occurs with one specific stream, maybe switching to
      a different audio channel (using the gui) helps. Some DVD streams have
      audio on strange channels.
    </para>
    <para>
      If all this doesn't help, maybe you're missing an audio codec or you found
      a bug. If you decide to post your problem on the xine-user mailing list,
      make sure to include all console output xine produced and also clearly 
      state what type of stream you tried to play back or, even better, make 
      a test stream available somewhere for developers to download and try.
    </para>
  </sect1>
  <sect1 id="surroundsound">

    <title>Can xine produce 4-/5-channel surround audio output?</title>
    
    <para>
      Yep, it can do that using OSS or ALSA drivers, provided that the driver
      supports it. On startup xine tells you what modes are supported by your
      audio driver, e.g:
      <programlisting>
        audio_alsa_out : supported modes are mono stereo (4-channel not enabled
          in xine config) (5-channel not enabled in xine config) (5.1-channel not
          enabled in xine config) (a/52 and DTS pass-through not enabled in xine
          config)
      </programlisting>
    </para>
    <para>
      On this machine 4-channel surround would be possible. However, since xine
      cannot detect if there are actually speakers connected to the additional
      channels, you'll have to activate that feature manually.
    </para>
    <para>
      You can do this either in the config dialog while xine is running (press
      the config button on the xine panel and go to the AUDIO tab) or have it
      the complicated way by editing the config file yourself which is located
      in your home directory in <filename>.gxine</filename>/<filename>.xine</filename>:
      <programlisting>
        # 4-channel:
          audio.four_channel:1
 
        # 5-channel:
          audio.five_channel:1

        # 5.1-channel
          audio.five_lfe_channel:0
      </programlisting>
    </para>
  </sect1>
  <sect1 id="spdif">

    <title>What about ac3 output via spdif to an external ac3 decoder?</title>
    
    <para>
      xine can do that too. Pretty much the same story as for 4-/5-channel
      surround (see above). You can either use the config dialog or edit
      the config file (<filename>~/.xine/config</filename>/<filename>~/.gxine/config</filename>) 
      yourself:
      <programlisting>
        audio.a52_pass_through:1
      </programlisting>
    </para>
  </sect1>
  <sect1 id="volumecontrol">

    <title>Changing the volume with the GUI control has no effect! What's up!?</title>
    
    <para>
      Some xine drivers do not support volume changing although the GUI
      will show the volume bar. Usually this is not xine's fault: aRts C
      API, for example, doesn't offer any volume property to applications.
      Similarly, with ac3 pass through it is not possible to set the volume.
    </para>
    <para>
      Note that recently we added support to "simulate" volume in aRts by
      changing sample values on-the-fly before delivering them to the driver.
      Not as good as having access to sound card's mixer but at least users 
      will not complain about lacking of volume bar anymore! :)
    </para>
  </sect1>

  <sect1 id="stuttering">
    <title> Audio is stuttering and i see a lot of "metronom: fixing sound card drift by -2115 pts" on the console output </title>

    <para>
      Might be a soundcard problem, if it only comes in longer intervals.
      Your soundcard does not keep it's sampling frequency accurately 
      enough, which results in audio and video
      getting out of sync and xine has to compensate. 
      Maybe switching to different drivers (alsa to oss or vise-versa)
      can help here.
    </para>
    <para>
      Another, whole different possibility is that you have some background
      process running which is messing with the clock (like some ntp client -
      chronny, ntpd, ...).
    </para>
    <para>
      Occasional messages of "fixing sound card drift" may happen on start and
      when playing a long stream (like a movie). This is normal behaviour, 
      nothing to worry about.
    </para>
  </sect1>
</chapter>

<chapter id="video">

  <title> Video related questions </title>
  <sect1 id="novideo">

    <title>I can hear the audio - but I don't see a picture!</title>
    
    <para>
      Probably your hardware is simply too slow - see above for some
      hints on how to speed things up.
    </para>
    <para>
      Another possibility is that you using a buggy Xv driver, see the next
      question.
    </para>
  </sect1>

  <sect1 id="xvextension">

    <title>How can I make xine use the Xv extension and what drivers do I need?</title>
    
    <para>
      xine will normally use Xv by default if it is available. In some cases
      you might need to choose Xv playback manually (when the <filename>~/.xine/config</filename>
      file for some reason says that you want to use XShm):
      <programlisting>
       xine -V Xv foo.mpg
      </programlisting>
    </para>
    <para>
      If this doesn't work for you, it may be possible that Xv is not present
      on your system.
    </para>
    <para>
      First you need to install/use XFree 4.x. Once you got that you have to
      make sure the XFree drivers you're using are supporting Xv on your
      hardware. Here are some hints for individual gfx chips:
      <itemizedlist>
        <listitem>
	  <para> 
	    3Dfx: if all you get is a solid black window, upgrade at least to
	    XFree 4.1.0
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    ATI: if you only get "half a picture", try lowering your resolution
	    or bit depth, disable DRI (looks like you ran out of video RAM)	    
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    Trident card: If you see vertical bands jumbled, upgrade to the latest
	    xfree/experimental trident drivers (for the CyberBlade XP
	    a driver exists here:
	    <ulink url="http://www.xfree86.org/~alanh/"> 
	    http://www.xfree86.org/~alanh/ </ulink>)
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    nvidia: With newer GeForce cards, Xv should work with XFree 4.2.0 or
	    newer, for older RivaTNT cards use the binary drivers from nvidia
	    (of course the binary drivers work as well for GeForce cards)
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    Mach64/Rage3D (not Rage128/Radeon) cards/chips get no XVideo with
	    standard drivers, try 
	    <ulink url="http://gatos.sourceforge.net/">GATOS drivers
	    </ulink> instead
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    intel: i815 has Xv support in XFree 4.x, others unknown	    
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    Permedia 2/3 has Xv support in XFree 4.x
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    Savage: at least some older drivers tend to lock up the whole machine,
	      try the drivers available from 
	      <ulink url="http://www.probo.com/timr/savage40.html">
	      www.probo.com/timr/savage40.html
	      </ulink>.
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    SIS: certain controllers (more info needed!) have Xv support in XFree 4.x
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    Chips and Tech 6555x, 68554, 69000, 69030 have Xv support in XFree 4.x
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    NeoMagic: certain controllers (more info needed!) have Xv support in Xfree 4.x
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    SiliconMotion: certain controllers (more info needed!) have Xv support in Xfree 4.x
	  </para>
	</listitem>
        <listitem>
	  <para> 
	    Matrox: G200 or newer (but not Parhelia) have Xv support in XFree 4.x.
	    For parhelia, use the binary only drivers available from matrox' website.
	  </para>
	</listitem>
      </itemizedlist>
    </para>
  </sect1>
  <sect1 id="colorkey">

    <title>Some parts of my X Desktop get transparent when xine plays the video!</title>
    
    <para>
      Looks like some colors on your GUI match the colorkey Xv uses. You can
      change the colorkey value to avoid this. There should be a line like:
      <programlisting>
        video.XV_COLORKEY:2110
      </programlisting>
      in your <filename>~/.xine/config</filename> file where you can change the color that's used
      by xine for the video overlay.
    </para>
  </sect1>
  <sect1 id="aspectratio">

    <title>The aspect ratio of the video is wrong!</title>
    
    <para>
    Try pressing "a" to change the aspect ratio.
    </para>
  </sect1>
  <sect1 id="discardedskipped">

    <title>What is the difference between discarded and skipped frames?</title>
    
    <para>
    Sometimes xine will output a message like that:
    <programlisting>
    200 frames delivered, XX frames skipped, YY frames discarded
    </programlisting>
    </para>
    <para>
      The difference between these counters is a little subtle for the non
      developer. There are two threads running in order to display video:
      the decoder thread will deliver frames to the video output thread. 
      The later is responsible for scheduling the frames to be displayed at
      the right time.
    </para>
    <para>
      If your system can't keep up with decoding requirements, decoder will
      deliver overdue frames. Imagine if it finished decoding the frame
      tagged for displaying at 11:30 but xine clock marks 11:31. When this
      situation is detected, xine will try to skip decoding a few frames
      to recover. Not every decoder may support this feature.
    </para>
    <para>
      When the frame is decoded to be shown somewhere in future but the
      output thread doesn't get scheduled in time by the operating system
      to complete the operation, the frame is discarded. One cause might
      be the disk access operation, which may halt the system for a few
      miliseconds without DMA. See performance section tips above.
    </para>
    <para>
      Note that if a decoder can't skip frames for some reason, you would
      never see frames skipped (they would be all discarded).
    </para>
  </sect1>
  <sect1 id="contrastbrightnesssaturation">

    <title>My xine is runing in black and white! / I only get a gray video output!</title>
    
    <para>
      This frequently happens with new Xv drivers or when switching to a
      different video card. Background is that different Xv drivers often
      use different ranges for the contrast/brightness/saturation settings.
    </para>
    <para>
      To fix this, try opening the xine settings window and try adjusting
      the sliders for contrast, brightness and saturation.
    </para>
    <para>
      Please note that some frontends save these settings in their config file
      so when you have found a working combination, make sure you exit 
      xine cleanly so the values are saved.
    </para>
  </sect1>
  
  <sect1 id="videodriver">

    <title>Which is the best video driver to use?</title>
    
    <para>
      xine support several video drivers for outputing the image. These will
      differ on how the frames are copied to the video card memory, whether
      colorspace conversion and scaling is done in software or hardware, among
      other things. They may also differ on ease of use and stability.
    </para>
    <para>
      Most of the time, Xv should give the users a good trade-off between
      quality, compatibility and ease of use. This is why xine tries to use
      Xv by default.
    </para>
    <para>
      However some users may want to explore better the available hardware 
      capabilities (eg. syncing frame drawing with monitor refresh).
      Also some Xv drivers contain slow copies and accessing the video card
      directly may yield performance gains.
    </para>
    <para>
      Drivers that access hardware directly includes VIDIX (warning: requires 
      root priviledges) and SyncFB (requires kernel helper - Matrox only).
      User may try one of those, but should be warned that with root access
      they can cause the system to crash hard. The support is also limited to
      a couple of graphics cards only.
    </para>
    <para>
      Graphic workstations like SGI have usually a good support for OpenGL.
      In that case, using OpenGL may be a better choice than XShm. However for
      most desktop systems the performance of OpenGL will be quite bad.
    </para>
  </sect1>
</chapter>

<chapter id="errors">

  <title> Error Messages: What they mean and what you can do</title>
  <sect1 id="audiodrivererr">

    <title>Starting xine fails with complains about audio drivers/devices!</title>
    
    <para>
      You can select the audio driver using the -A option. So try:
      <programlisting>
        xine -A null
      </programlisting>
      If you have ALSA drivers installed, try:
      <programlisting>
        xine -A alsa
      </programlisting>
      If you run ESD (not recommended), try:
      <programlisting>
        xine -A esd
      </programlisting>
      If you run artsd, try:
      <programlisting>
        xine -A arts
      </programlisting>
    </para>
  </sect1>
  <sect1 id="novideoportfound">

    <title>"no video port found"</title>
    
    <para>
      You got the Xv extension, but your video card driver doesn't support it.
      First try to find a driver that does support Xv on your hardware (check
      your graphics card vendor). If your driver has Xv support but you can't
      get it working, try at a lower resolution (1024x768 is enough even for
      anamorphic mpeg-2).    
    </para>
    <para>
      If all that fails, you can still use plain X11/XShm:
      <programlisting>
        gxine -V XShm foo.vob
      </programlisting>
    </para>
  </sect1>
  <sect1 id="unabletoopendvddrive">

    <title>"Unable to open dvd drive (/dev/dvd)" </title>
    
    <para>
      You probably don't have /dev/dvd (check that). If so, simply create a
      link /dev/dvd that points to your DVD device. Something like...
      <programlisting>
        cd /dev
        ln -s hdc dvd
      </programlisting>
       ...should do the job. Also make sure you have read access on
       the device the symlink points to.
       See the <link linkend="dvdplayback">dvd playback section</link>
       for more information.
    </para>
  </sect1>
  <sect1 id="demuxerror0000">

    <title>"demux error! 00 00 00 (should be 0x000001)"</title>
    
    <para>
      Probably xine can't access your input source. Most commonly this happens
      when you're trying to play locked/encrypted DVDs. Remember that xine
      can't play such DVDs out-of-the box for legal reasons (see above).
    </para>
    <para>
      If it is legal where you live, you can try to install libdvdcss. Once
      you have done that and re-start xine, it should automatically detect
      and use it to play back encrypted DVDs.
    </para>
    <para>
      Another reason could be that your (RPC-2) DVD drive isn't set up
      for the right region (see above).
    </para>
  </sect1>
  <sect1 id="ossfailed">

    <title>"audio driver 'oss' failed, using null driver instead"</title>
    
    <para>
       First of all, make sure that your OSS Audio drivers are working (i.e.
       you can play music with other software). Maybe you're using alsa?
       If so, try <command> gxine -A alsa </command> to see if this helps.
    </para>
    <para>
      The most common reason for oss not working is that some other program is accesing
      your audio device. If you're using linux, the command <command>fuser /dev/dsp</command>
      should give you the PID of the process.
    </para>
    <para>
      If you are using GNOME, chances are that this is caused by ESD. Now you
      have two possibilities. Either deactivate ESD (temporarily) by right
      clicking on the sound monitor applet and selecting "Place Esound in
      standby" or just kill it. Then xine will use OSS audio output. The other
      method is to make xine use ESD for audio output with:      
      <programlisting>
        gxine -A esd
      </programlisting>
      This may result in worse playback - exact syncronization is not possible
      with esd, so using oss should be preferred.
    </para>
    <para>
      If you are using KDE, there is the possibility that the aRts sound
      daemon is currently running and thus blocking your sound device. You
      can check that by starting the aRts control (in your KDE menu it should
      be under Multimedia). If it is running, you can either use the aRts
      audio output plugin:
      <programlisting>
        gxine -A arts
      </programlisting>
      Or you suspend the aRts daemon by checking the appropriate option in
      your aRts control. (recommended)
    </para>
    <para>
      Newer versions of arts have an auto-suspend mode - this can lead to
      some nondeterministic behaviour of xine if it is set up to use
      the audio device directly. Using arts is recommended in that case,
      however you will loose the ability to do four/five channel audio output.
    </para>
  </sect1>
  <sect1 id="throwingawarimage">

    <title>"video_out: throwing away image with pts xxx because it's too old"</title>
    
    <para>
      This is a performance related problem.
      
      If you have a fast computer and this message shows from time to
      time playing dvd/cdrom, it's very likely that your drive is not
      DMA enabled. 
    </para>
  </sect1>
  <sect1 id="novideopluginavailable">

    <title>"No video plugin available to decode 'xxxxxx'."</title>
    
    <para>
      You have tried to play a stream using a unknown or unhandled codec.
      Possibly the file uses some obscure proprietary format and no
      information is available on how to decode it.
    </para>
    <para>
      If you're on an x86 platform (e.g. PC hardware) you might want to
      try installing binary-only windows medial, real networks and
      quicktime codecs (see above).
    </para>
  </sect1>
  <sect1 id="demuxerfailedtostart">

    <title>"w32codec: decoder failed to start. Is 'xxxxxx' installed?"</title>
    
    <para>
      You probably don't have the win32 dll needed to decode this file.
    </para>
  </sect1>
  <sect1 id="xinecrashed">

    <title>xine just crashed on me - i didn't get any error message</title>
    
    <para>
      OK, yes, that shouldn't happen and you're upset. We can understand that.
      But, to help you and of course to fix this, we need some information.
      So, let's go through the checklist and maybe prepare a nice bug report
      for the xine-user mailing list:
    </para>

    <itemizedlist>
      <listitem>
        <para>
	  did xine really crash (segfault) or did it hang (deadlock) ?
	</para>
      </listitem>
      <listitem>
        <para>
	  can you reproduce the bug? (e.g. do you remember what you
	  did and when you do it again it crashes again?) 
	</para>
      </listitem>
      <listitem>
        <para>
          is that a specific media file or format which crashes xine? (have you
          tried other files types?)
	</para>
      </listitem>
      <listitem>
        <para>
	  check the console output (and include it in a bug report), maybe earlier
	  there is some output that points to the problem.
	</para>
      </listitem>
      <listitem>
        <para>
	  Your X server just froze on you? unfortunately that's a known problem
	  with some chipsets and drivers (most commonly Savage chipsets) when
	  using Xv. You might want to try running <command> gxine -V XShm </command>
	  to see if the problem is related to the Xv driver.  This will unfortunately 
	  be much slower, as lots of things are now done
	  in software instead of hardware scaling/colour space conversion.
	</para>
	<para>
  	  Maybe at the time you read this, there's an XFree upgrade which fixes
          this for the Savage driver. If that works for you, please notify the xine crew at
	  <email> xine-user@lists.sf.net </email>, so they can update this FAQ!
	</para>
      </listitem>
      <listitem>
        <para>
	  Even though we try to make each release as bug free as possible, xine is
          still under heavy development (nice excuse, isn't it? *grin*).
	</para>
	<para>
	  If you write to the xine user mailing list 
	  <email>xine-user@lists.sourceforge.net</email>
	  make sure you include a the above information (when applicable)
	  and also some information about your machine (operating system, cpu type and
	  speed, gfx card, sound card, ...) and please use a meaningfull subject
	  line ("xine bug" is bad, "xine fails to play this quicktime trailer in fullscreen mode"
	  ist much better).
	</para>
	<para>
          Thanks for taking the time to help improve xine.
	</para>
      </listitem>
    </itemizedlist>
  </sect1>
</chapter>

</book>